#ifndef __CONFIG_H
#define __CONFIG_H
+#define CONFIG_SKIP_RELOCATE_UBOOT
+
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_X86 1 /* This is a X86 CPU */
-#define CONFIG_SC520 1 /* Include support for AMD SC520 */
+#define CONFIG_SYS_SC520 1 /* Include support for AMD SC520 */
+#define CONFIG_SYS_SC520_SSI
-#define CFG_SDRAM_PRECHARGE_DELAY 6 /* 6T */
-#define CFG_SDRAM_REFRESH_RATE 78 /* 7.8uS (choices are 7.8, 15.6, 31.2 or 62.5uS) */
-#define CFG_SDRAM_RAS_CAS_DELAY 3 /* 3T */
+#define CONFIG_SYS_SDRAM_PRECHARGE_DELAY 6 /* 6T */
+#define CONFIG_SYS_SDRAM_REFRESH_RATE 78 /* 7.8uS (choices are 7.8, 15.6, 31.2 or 62.5uS) */
+#define CONFIG_SYS_SDRAM_RAS_CAS_DELAY 3 /* 3T */
/* define at most one of these */
-#undef CFG_SDRAM_CAS_LATENCY_2T
-#define CFG_SDRAM_CAS_LATENCY_3T
+#undef CONFIG_SYS_SDRAM_CAS_LATENCY_2T
+#define CONFIG_SYS_SDRAM_CAS_LATENCY_3T
-#define CFG_SC520_HIGH_SPEED 0 /* 100 or 133MHz */
-#define CFG_RESET_GENERIC 1 /* use tripple-fault to reset cpu */
-#undef CFG_RESET_SC520 /* use SC520 MMCR's to reset cpu */
-#undef CFG_TIMER_SC520 /* use SC520 swtimers */
-#define CFG_TIMER_GENERIC 1 /* use the i8254 PIT timers */
-#undef CFG_TIMER_TSC /* use the Pentium TSC timers */
+#define CONFIG_SYS_SC520_HIGH_SPEED 0 /* 100 or 133MHz */
+#undef CONFIG_SYS_SC520_RESET /* use SC520 MMCR's to reset cpu */
+#undef CONFIG_SYS_SC520_TIMER /* use SC520 swtimers */
+#define CONFIG_SYS_GENERIC_TIMER 1 /* use the i8254 PIT timers */
+#undef CONFIG_SYS_TSC_TIMER /* use the Pentium TSC timers */
+#define CONFIG_SYS_PCAT_INTERRUPTS
+#define CONFIG_SYS_NUM_IRQS 16
-#define CFG_STACK_SIZE 0x8000 /* Size of bootloader stack */
+#define CONFIG_SYS_STACK_SIZE 0x8000 /* Size of bootloader stack */
#define CONFIG_SHOW_BOOT_PROGRESS 1
#define CONFIG_LAST_STAGE_INIT 1
/*
* Size of malloc() pool
*/
-#define CONFIG_MALLOC_SIZE (CFG_ENV_SIZE + 128*1024)
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
#define CONFIG_BAUDRATE 9600
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_JFFS2 | CFG_CMD_IDE | CFG_CMD_NET | CFG_CMD_PCMCIA | CFG_CMD_EEPROM)
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTDELAY 15
-#define CONFIG_BOOTARGS "root=/dev/mtdblock1 console=ttyS0,9600 mtdparts=phys:7936k(root),256k(uboot) "
-#define CONFIG_BOOTCOMMAND "setenv bootargs root=/dev/nfs ip=autoconf console=ttyS0,9600 mtdparts=phys:7808k(root),128k(env),256k(uboot); bootp; bootm"
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCMCIA
+#define CONFIG_CMD_EEPROM
+
+
+#define CONFIG_BOOTDELAY 15
+#define CONFIG_BOOTARGS "root=/dev/mtdblock1 console=ttyS0,9600 " \
+ "mtdparts=phys:7936k(root),256k(uboot) "
+#define CONFIG_BOOTCOMMAND "setenv bootargs root=/dev/nfs ip=autoconf " \
+ "console=ttyS0,9600 " \
+ "mtdparts=phys:7808k(root),128k(env),256k(uboot);" \
+ "bootp;bootm"
+
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "boot > " /* Monitor Command Prompt */
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "boot > " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x01000000 /* 1 ... 16 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x01000000 /* 1 ... 16 MB in DRAM */
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-
-#define CFG_HZ 1024 /* incrementer freq: 1kHz */
+#define CONFIG_SYS_HZ 1024 /* incrementer freq: 1kHz */
/* valid baudrates */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*-----------------------------------------------------------------------
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
/* timeout values are in ticks */
-#define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* Timeout for Flash Erase */
-#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* Timeout for Flash Write */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Write */
#define CONFIG_SPI_EEPROM /* SPI EEPROMs such as AT25010 or AT25640 */
#define CONFIG_MW_EEPROM /* MicroWire EEPROMS such as AT93LC46 */
-#define CONFIG_DS1722 /* Dallas DS1722 SPI Temperature probe */
-
+#define CONFIG_DTT_DS1722 /* Dallas DS1722 SPI Temperature probe */
+
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#if 0
/* Environment in flash */
-#define CFG_ENV_IS_IN_FLASH 1
-# define CFG_ENV_ADDR (0x387a0000) /* Addr of Environment Sector */
-# define CFG_ENV_SIZE 0x20000 /* Total Size of Environment Sector (or 0x10000) */
-# define CFG_ENV_OFFSET 0
+#define CONFIG_ENV_IS_IN_FLASH 1
+# define CONFIG_ENV_ADDR (0x387a0000) /* Addr of Environment Sector */
+# define CONFIG_ENV_SIZE 0x20000 /* Total Size of Environment Sector (or 0x10000) */
+# define CONFIG_ENV_OFFSET 0
#else
/* Environment in EEPROM */
-# define CFG_ENV_IS_IN_EEPROM 1
+# define CONFIG_ENV_IS_IN_EEPROM 1
# define CONFIG_SPI
# define CONFIG_SPI_X 1
-# define CFG_ENV_SIZE 0x2000 /* Total Size of Environment EEPROM */
-# define CFG_ENV_OFFSET 0x1c00
+# define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment EEPROM */
+# define CONFIG_ENV_OFFSET 0x1c00
#endif
-#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS 1 /* */
+/*
+ * JFFS2 partitions
+ *
+ */
+/* No command line, one static partition, whole device */
+#undef CONFIG_CMD_MTDPARTS
+#define CONFIG_JFFS2_DEV "nor0"
+#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
+#define CONFIG_JFFS2_PART_OFFSET 0x00000000
+
+/* mtdparts command line support */
+/* Note: fake mtd_id used, no linux mtd map file */
+/*
+#define CONFIG_CMD_MTDPARTS
+#define MTDIDS_DEFAULT "nor0=sc520_spunk-0"
+#define MTDPARTS_DEFAULT "mtdparts=sc520_spunk-0:-(jffs2)"
+*/
/*-----------------------------------------------------------------------
* Device drivers
*/
#define CONFIG_NET_MULTI /* Multi ethernet cards support */
#define CONFIG_EEPRO100
+#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
/************************************************************
* IDE/ATA stuff
************************************************************/
-#define CFG_IDE_MAXBUS 2 /* max. 2 IDE busses */
-#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
-#define CFG_ATA_BASE_ADDR 0
-#define CFG_ATA_IDE0_OFFSET 0x01f0 /* ide0 offset */
-#define CFG_ATA_IDE1_OFFSET 0xe000 /* ide1 offset */
-#define CFG_ATA_DATA_OFFSET 0 /* data reg offset */
-#define CFG_ATA_REG_OFFSET 0 /* reg offset */
-#define CFG_ATA_ALT_OFFSET 0x200 /* alternate register offset */
+#define CONFIG_SYS_IDE_MAXBUS 2 /* max. 2 IDE busses */
+#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
+#define CONFIG_SYS_ATA_BASE_ADDR 0
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x01f0 /* ide0 offset */
+#define CONFIG_SYS_ATA_IDE1_OFFSET 0xe000 /* ide1 offset */
+#define CONFIG_SYS_ATA_DATA_OFFSET 0 /* data reg offset */
+#define CONFIG_SYS_ATA_REG_OFFSET 0 /* reg offset */
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x200 /* alternate register offset */
-#define CFG_FISRT_PCMCIA_BUS 1
+#define CONFIG_SYS_FIRST_PCMCIA_BUS 1
#undef CONFIG_IDE_LED /* no led for ide supported */
#undef CONFIG_IDE_RESET /* reset for ide unsupported... */
#undef CONFIG_IDE_RESET_ROUTINE /* no special reset function */
#define CONFIG_IDE_TI_CARDBUS
-#define CFG_PCMCIA_CIS_WIN 0x27f00000
-#define CFG_PCMCIA_CIS_WIN_SIZE 0x00100000
-#define CFG_PCMCIA_IO_WIN 0xe000
-#define CFG_PCMCIA_IO_WIN_SIZE 16
+#define CONFIG_SYS_PCMCIA_CIS_WIN 0x27f00000
+#define CONFIG_SYS_PCMCIA_CIS_WIN_SIZE 0x00100000
+#define CONFIG_SYS_PCMCIA_IO_WIN 0xe000
+#define CONFIG_SYS_PCMCIA_IO_WIN_SIZE 16
+#define CONFIG_PCMCIA_SLOT_A /* TODO: Check this */
/************************************************************
* DISK Partition support
#define CONFIG_ISO_PARTITION /* Experimental */
-
-
/************************************************************
* RTC
***********************************************************/
#define CONFIG_PCI_PNP /* pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW
-#define CFG_FIRST_PCI_IRQ 9
-#define CFG_SECOND_PCI_IRQ 10
-#define CFG_THIRD_PCI_IRQ 11
-#define CFG_FORTH_PCI_IRQ 12
-
+#define CONFIG_SYS_FIRST_PCI_IRQ 9
+#define CONFIG_SYS_SECOND_PCI_IRQ 10
+#define CONFIG_SYS_THIRD_PCI_IRQ 11
+#define CONFIG_SYS_FORTH_PCI_IRQ 12
#endif /* __CONFIG_H */