#define CONFIG_X86 1 /* This is a X86 CPU */
#define CONFIG_SC520 1 /* Include support for AMD SC520 */
-#define CFG_SDRAM_PRECHARGE_DELAY 6 /* 6T */
+#define CFG_SDRAM_PRECHARGE_DELAY 6 /* 6T */
#define CFG_SDRAM_REFRESH_RATE 78 /* 7.8uS (choices are 7.8, 15.6, 31.2 or 62.5uS) */
#define CFG_SDRAM_RAS_CAS_DELAY 3 /* 3T */
#define CONFIG_BAUDRATE 9600
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_JFFS2 | CFG_CMD_IDE | CFG_CMD_NET | CFG_CMD_PCMCIA | CFG_CMD_EEPROM)
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCMCIA
+#define CONFIG_CMD_EEPROM
+
#define CONFIG_BOOTDELAY 15
#define CONFIG_BOOTARGS "root=/dev/mtdblock1 console=ttyS0,9600 mtdparts=phys:7936k(root),256k(uboot) "
-#define CONFIG_BOOTCOMMAND "setenv bootargs root=/dev/nfs ip=autoconf console=ttyS0,9600 mtdparts=phys:7808k(root),128k(env),256k(uboot); bootp; bootm"
+#define CONFIG_BOOTCOMMAND "setenv bootargs root=/dev/nfs ip=autoconf console=ttyS0,9600 mtdparts=phys:7808k(root),128k(env),256k(uboot); bootp; bootm"
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
#define CONFIG_SPI_EEPROM /* SPI EEPROMs such as AT25010 or AT25640 */
#define CONFIG_MW_EEPROM /* MicroWire EEPROMS such as AT93LC46 */
#define CONFIG_DS1722 /* Dallas DS1722 SPI Temperature probe */
-
+
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#if 0
/* Environment in flash */
-#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_IS_IN_FLASH 1
# define CFG_ENV_ADDR (0x387a0000) /* Addr of Environment Sector */
# define CFG_ENV_SIZE 0x20000 /* Total Size of Environment Sector (or 0x10000) */
# define CFG_ENV_OFFSET 0
# define CONFIG_SPI
# define CONFIG_SPI_X 1
# define CFG_ENV_SIZE 0x2000 /* Total Size of Environment EEPROM */
-# define CFG_ENV_OFFSET 0x1c00
+# define CFG_ENV_OFFSET 0x1c00
#endif
-#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS 1 /* */
+/*
+ * JFFS2 partitions
+ *
+ */
+/* No command line, one static partition, whole device */
+#undef CONFIG_JFFS2_CMDLINE
+#define CONFIG_JFFS2_DEV "nor0"
+#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
+#define CONFIG_JFFS2_PART_OFFSET 0x00000000
+
+/* mtdparts command line support */
+/* Note: fake mtd_id used, no linux mtd map file */
+/*
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nor0=sc520_spunk-0"
+#define MTDPARTS_DEFAULT "mtdparts=sc520_spunk-0:-(jffs2)"
+*/
/*-----------------------------------------------------------------------
* Device drivers
*/
#define CONFIG_NET_MULTI /* Multi ethernet cards support */
#define CONFIG_EEPRO100
+#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
/************************************************************
* IDE/ATA stuff
#define CFG_ATA_REG_OFFSET 0 /* reg offset */
#define CFG_ATA_ALT_OFFSET 0x200 /* alternate register offset */
-#define CFG_FISRT_PCMCIA_BUS 1
+#define CFG_FIRST_PCMCIA_BUS 1
#undef CONFIG_IDE_LED /* no led for ide supported */
#undef CONFIG_IDE_RESET /* reset for ide unsupported... */
#define CONFIG_ISO_PARTITION /* Experimental */
-
-
/************************************************************
* RTC
***********************************************************/
#define CONFIG_PCI_SCAN_SHOW
#define CFG_FIRST_PCI_IRQ 9
-#define CFG_SECOND_PCI_IRQ 10
-#define CFG_THIRD_PCI_IRQ 11
+#define CFG_SECOND_PCI_IRQ 10
+#define CFG_THIRD_PCI_IRQ 11
#define CFG_FORTH_PCI_IRQ 12
-
#endif /* __CONFIG_H */