#ifndef __CONFIG_H
#define __CONFIG_H
+#define GRUSS_TESTING
/*
* High Level Configuration Options
* (easy to change)
#define CONFIG_SC520 1 /* Include support for AMD SC520 */
#define CONFIG_ALI152X 1 /* Include support for Ali 152x SIO */
-#define CFG_SDRAM_PRECHARGE_DELAY 6 /* 6T */
+#define CFG_SDRAM_PRECHARGE_DELAY 6 /* 6T */
#define CFG_SDRAM_REFRESH_RATE 78 /* 7.8uS (choices are 7.8, 15.6, 31.2 or 62.5uS) */
#define CFG_SDRAM_RAS_CAS_DELAY 3 /* 3T */
/*
* Size of malloc() pool
*/
-#define CONFIG_MALLOC_SIZE (CFG_ENV_SIZE + 128*1024)
-
+#define CONFIG_MALLOC_SIZE (CONFIG_ENV_SIZE + 128*1024)
#define CONFIG_BAUDRATE 9600
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_JFFS2 | CFG_CMD_IDE | CFG_CMD_NET | CFG_CMD_EEPROM)
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PCI
+#ifndef GRUSS_TESTING
+#define CONFIG_CMD_SATA
+#else
+#undef CONFIG_CMD_SATA
+#endif
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_EEPROM
#define CONFIG_BOOTDELAY 15
-#define CONFIG_BOOTARGS "root=/dev/mtdblock0 console=ttyS0,9600"
+#define CONFIG_BOOTARGS "root=/dev/mtdblock0 console=ttyS0,9600"
/* #define CONFIG_BOOTCOMMAND "bootm 38000000" */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
-
/*
* Miscellaneous configurable options
*/
/* valid baudrates */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
/*-----------------------------------------------------------------------
* Physical Memory Map
*/
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
-
-
#define CFG_MAX_FLASH_BANKS 3 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* Timeout for Flash Write */
#define CONFIG_SPI_EEPROM /* Support for SPI EEPROMs (AT25128) */
-#define CONFIG_MW_EEPROM /* Support for MicroWire EEPROMs (AT93LC46) */
-
+#define CONFIG_MW_EEPROM /* Support for MicroWire EEPROMs (AT93LC46) */
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
-
/* Environment in EEPROM */
-#define CFG_ENV_IS_IN_EEPROM 1
+#define CONFIG_ENV_IS_IN_EEPROM 1
#define CONFIG_SPI
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment EEPROM 16k is SPI is used or 128 bytes if MW is used*/
-#define CFG_ENV_OFFSET 0
+#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment EEPROM 16k is SPI is used or 128 bytes if MW is used*/
+#define CONFIG_ENV_OFFSET 0
#define CONFIG_SC520_CDP_USE_SPI /* Store configuration in the SPI part */
#undef CONFIG_SC520_CDP_USE_MW /* Store configuration in the MicroWire part */
#define CONFIG_SPI_X 1
-#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS 1 /* */
+
+/*
+ * JFFS2 partitions
+ */
+/* No command line, one static partition, whole device */
+#undef CONFIG_JFFS2_CMDLINE
+#define CONFIG_JFFS2_DEV "nor0"
+#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
+#define CONFIG_JFFS2_PART_OFFSET 0x00000000
+
+/* mtdparts command line support */
+/*
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nor0=SC520CDP Flash Bank #0"
+#define MTDPARTS_DEFAULT "mtdparts=SC520CDP Flash Bank #0:-(jffs2)"
+*/
/*-----------------------------------------------------------------------
* Device drivers
#define PCNET_HAS_PROM 1
/************************************************************
- * IDE/ATA stuff
- ************************************************************/
-#define CFG_IDE_MAXBUS 1 /* max. 2 IDE busses */
-#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
-
-#define CFG_ATA_IDE0_OFFSET 0x01F0 /* ide0 offste */
-//#define CFG_ATA_IDE1_OFFSET 0x0170 /* ide1 offset */
-#define CFG_ATA_DATA_OFFSET 0 /* data reg offset */
-#define CFG_ATA_REG_OFFSET 0 /* reg offset */
-#define CFG_ATA_ALT_OFFSET 0x200 /* alternate register offset */
-#define CFG_ATA_BASE_ADDR 0
-
-#undef CONFIG_IDE_LED /* no led for ide supported */
-#undef CONFIG_IDE_RESET /* reset for ide unsupported... */
-#undef CONFIG_IDE_RESET_ROUTINE /* no special reset function */
+*SATA/Native Stuff
+************************************************************/
+#ifndef GRUSS_TESTING
+#define CFG_SATA_MAXBUS 2 /*Max Sata buses supported */
+#define CFG_SATA_DEVS_PER_BUS 2 /*Max no. of devices per bus/port */
+#define CFG_SATA_MAX_DEVICE (CFG_SATA_MAXBUS* CFG_SATA_DEVS_PER_BUS)
+#define CONFIG_ATA_PIIX 1 /*Supports ata_piix driver */
+#else
+#undef CFG_SATA_MAXBUS
+#undef CFG_SATA_DEVS_PER_BUS
+#undef CFG_SATA_MAX_DEVICE
+#undef CONFIG_ATA_PIIX
+#endif
-/************************************************************
- * ATAPI support (experimental)
- ************************************************************/
-#define CONFIG_ATAPI /* enable ATAPI Support */
/************************************************************
* DISK Partition support
/************************************************************
* Video/Keyboard support
************************************************************/
+#ifndef GRUSS_TESTING
#define CONFIG_VIDEO /* To enable video controller support */
+#else
+#undef CONFIG_VIDEO
+#endif
#define CONFIG_I8042_KBD
#define CFG_ISA_IO 0
-
-
/************************************************************
* RTC
***********************************************************/
/*
* PCI stuff
*/
+#ifndef GRUSS_TESTING
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_PNP /* pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW
#define CFG_FIRST_PCI_IRQ 10
-#define CFG_SECOND_PCI_IRQ 9
-#define CFG_THIRD_PCI_IRQ 11
+#define CFG_SECOND_PCI_IRQ 9
+#define CFG_THIRD_PCI_IRQ 11
#define CFG_FORTH_PCI_IRQ 15
+#else
+#undef CONFIG_PCI
+#undef CONFIG_PCI_PNP
+#undef CONFIG_PCI_SCAN_SHOW
+#endif
#endif /* __CONFIG_H */