#define CONFIG_4xx 1
#define CONFIG_405GP 1
+#define CONFIG_SYS_TEXT_BASE 0xFFFA0000
+
#define CONFIG_BOARD_EARLY_INIT_F 1
+#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r() */
/*
* Define IDE_USES_ISA_EMULATION for slower IDE access in the ISA-IO address range
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
-#define CONFIG_SERIAL_MULTI
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
-/*
- * define CONFIG_POWER_DOWN if your cpu should power down while waiting for your input
- * Works only, if you have enabled the CONFIG_SERIAL_SOFTWARE_FIFO feature
- */
-#if CONFIG_SERIAL_SOFTWARE_FIFO
- #define CONFIG_POWER_DOWN
-#endif
+#define CONFIG_CONS_INDEX 1 /* Use UART0 */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_serial_clock()
/*
* define CONFIG_SYS_CLK_FREQ to your base crystal clock in Hz
#undef CONFIG_LOADS_ECHO /* no echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#define CONFIG_NET_MULTI
/* #define CONFIG_EEPRO100_SROM_WRITE */
/* #define CONFIG_SHOW_MAC */
#define CONFIG_EEPRO100
*/
#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
#define I2C_INIT
#define I2C_ACTIVE 0
#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
#define CONFIG_PCI_PNP /* do pci plug-and-play */
/* resource configuration */
* CONFIG_SYS_FLASH_BASE -> start address of internal flash
* CONFIG_SYS_MONITOR_BASE -> start of u-boot
*/
-#ifndef __ASSEMBLER__
-extern unsigned long offsetOfBigFlash;
-extern unsigned long offsetOfEnvironment;
-#endif
-
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_FLASH_BASE 0xFFE00000
-#define CONFIG_SYS_MONITOR_BASE 0xFFFC0000 /* placed last 256k */
-#define CONFIG_SYS_MONITOR_LEN (224 * 1024) /* Reserve 224 KiB for Monitor */
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* Start of U-Boot */
+#define CONFIG_SYS_MONITOR_LEN (0xFFFFFFFF - CONFIG_SYS_MONITOR_BASE + 1)
#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 KiB for malloc() */
/*
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE 0x77D00000
-#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
-
#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */
/* No command line, one static partition */
* - internal SRAM (OCM=On Chip Memory) is placed to CONFIG_SYS_OCM_DATA_ADDR
* - Stackpointer will be located to
* (CONFIG_SYS_INIT_RAM_ADDR&0xFFFF0000) | (CONFIG_SYS_INIT_SP_OFFSET&0x0000FFFF)
- * in cpu/ppc4xx/start.S
+ * in arch/powerpc/cpu/ppc4xx/start.S
*/
#undef CONFIG_SYS_INIT_DCACHE_CS
/* Where the internal SRAM starts */
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR
/* Where the internal SRAM ends (only offset) */
-#define CONFIG_SYS_INIT_RAM_END 0x0F00
+#define CONFIG_SYS_INIT_RAM_SIZE 0x0F00
/*
| |
| 64 Bytes |
| |
- CONFIG_SYS_INIT_RAM_END ------> ------------ higher address
+ CONFIG_SYS_INIT_RAM_SIZE ------> ------------ higher address
(offset only)
*/
-/* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_SIZE 64
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/* Initial value of the stack pointern in internal SRAM */
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
/* ################################################################################### */
-/* These defines will be used in cpu/ppc4xx/cpu_init.c to setup external chip selects */
+/* These defines will be used in arch/powerpc/cpu/ppc4xx/cpu_init.c to setup external chip selects */
/* They are currently undefined cause they are initiaized in board/solidcard3/init.S */
/* This chip select accesses the boot device */
#define CONFIG_SYS_EBC_CFG 0xb84ef000
-#define CONFIG_SDRAM_BANK0 /* use the standard SDRAM initialization */
+#undef CONFIG_SDRAM_BANK0 /* use private SDRAM initialization */
#undef CONFIG_SPD_EEPROM
/*
#define CONFIG_SYS_ISA_MEM_BASE_ADDRESS 0x78000000
/*
- Die Grafik-Treiber greifen über die Adresse in diesem Macro auf den Chip zu.
+ Die Grafik-Treiber greifen über die Adresse in diesem Macro auf den Chip zu.
Das funktioniert bei deren Karten, weil sie eine PCI-Bridge benutzen, die
- das gleiche Mapping durchführen kann, wie der SC520 (also Aufteilen von IO-Zugriffen
+ das gleiche Mapping durchführen kann, wie der SC520 (also Aufteilen von IO-Zugriffen
auf ISA- und PCI-Zyklen)
*/
#define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0xE8000000