* Define IDE_USES_ISA_EMULATION for slower IDE access in the ISA-IO address range
* If undefined, IDE access uses a seperat emulation with higher access speed.
* Consider to inform your Linux IDE driver about the different addresses!
- * IDE_USES_ISA_EMULATION is only used if your CONFIG_COMMANDS macro includes
- * the CFG_CMD_IDE macro!
+ * IDE_USES_ISA_EMULATION is only used if you define CONFIG_CMD_IDE!
*/
#define IDE_USES_ISA_EMULATION
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
#if 1 /* feel free to disable for development */
#define CONFIG_AUTOBOOT_KEYED /* Enable password protection */
-#define CONFIG_AUTOBOOT_PROMPT "\nSC3 - booting... stop with ENTER\n"
+#define CONFIG_AUTOBOOT_PROMPT \
+ "\nSC3 - booting... stop with ENTER\n"
#define CONFIG_AUTOBOOT_DELAY_STR "\r" /* 1st "password" */
#define CONFIG_AUTOBOOT_DELAY_STR2 "\n" /* 1st "password" */
#endif
#define CONFIG_MII 1 /* add 405GP MII PHY management */
#define CONFIG_PHY_ADDR 1 /* the connected Phy defaults to address 1 */
-#define CONFIG_COMMANDS \
- (CONFIG_CMD_DFL | \
- CFG_CMD_AUTOSCRIPT | \
- CFG_CMD_PCI | \
- CFG_CMD_IRQ | \
- CFG_CMD_NET | \
- CFG_CMD_MII | \
- CFG_CMD_PING | \
- CFG_CMD_NAND | \
- CFG_CMD_JFFS2 | \
- CFG_CMD_I2C | \
- CFG_CMD_IDE | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_CACHE | \
- CFG_CMD_ELF )
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_ELF
+
#undef CONFIG_WATCHDOG /* watchdog disabled */
* External peripheral base address
*-----------------------------------------------------------------------
*/
-#if !(CONFIG_COMMANDS & CFG_CMD_IDE)
+#if !defined(CONFIG_CMD_IDE)
#undef CONFIG_IDE_LED /* no led for ide supported */
#undef CONFIG_IDE_RESET /* no reset for ide supported */
* IDE/ATA stuff
*-----------------------------------------------------------------------
*/
-#else /* !(CONFIG_COMMANDS & CFG_CMD_IDE) */
+#else
#define CONFIG_START_IDE 1 /* check, if use IDE */
#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
#endif /* IDE_USES_ISA_EMULATION */
-#endif /* !(CONFIG_COMMANDS & CFG_CMD_IDE) */
+#endif
/*
#define CFG_KEY_REG_BASE_ADDR 0xF0100000
#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
#define CFG_FLASH_CFI /* flash is CFI compat. */
-#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver*/
+#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver*/
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector */
#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash*/
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CFG_WRITE_SWAPPED_DATA /* swap Databytes between reading/writing */
-#define CFG_ENV_IS_IN_FLASH 1
-#if CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_OFFSET 0x00000000 /* Offset of Environment Sector in bottom type */
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
-#define CFG_ENV_SECT_SIZE 0x4000 /* see README - env sector total size */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_OFFSET 0x00000000 /* Offset of Environment Sector in bottom type */
+#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_SECT_SIZE 0x4000 /* see README - env sector total size */
/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET+CFG_ENV_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#endif
/* let us changing anything in our environment */
#define CONFIG_JFFS2_PART_SIZE 0x01000000
#define CONFIG_JFFS2_PART_OFFSET 0x00000000
-/*-----------------------------------------------------------------------
- * Cache Configuration
- *
- * CFG_DCACHE_SIZE -> size of data cache:
- * - 405GP 8k
- * - 405GPr 16k
- * How to handle the difference in chache size?
- * CFG_CACHELINE_SIZE -> size of one cache line: 32 bytes
- * (used in cpu/ppc4xx/start.S)
-*/
-#define CFG_DCACHE_SIZE 16384
-
-#define CFG_CACHELINE_SIZE 32
-
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
- #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
/*
* Init Memory Controller:
*