#define __CONFIG_H
/* High Level Configuration Options */
-#define CONFIG_MPC8641 1 /* MPC8641 specific */
#define CONFIG_SBC8641D 1 /* SBC8641D board specific */
#define CONFIG_MP 1 /* support multiple processors */
#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
#define CONFIG_SYS_SRIO
#define CONFIG_SRIO1 /* SRIO port 1 */
-#define CONFIG_PCI 1 /* Enable PCIE */
-#define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */
-#define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */
+#define CONFIG_PCIE1 1 /* PCIE controller 1 (slot 1) */
+#define CONFIG_PCIE2 1 /* PCIE controller 2 (slot 2) */
#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
-#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#undef CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-#define CONFIG_NUM_DDR_CONTROLLERS 2
#define CACHE_LINE_INTERLEAVING 0x20000000
#define PAGE_INTERLEAVING 0x21000000
#define BANK_INTERLEAVING 0x22000000
#define SUPER_BANK_INTERLEAVING 0x23000000
-
#define CONFIG_ALTIVEC 1
/*
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
#endif
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-
#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */
#define CONFIG_SYS_MEMTEST_END 0x00400000
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CONFIG_SYS_CCSRBAR 0xf8000000 /* relocated CCSRBAR */
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
#define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */
#define CONFIG_VERY_BIG_RAM
-#define CONFIG_NUM_DDR_CONTROLLERS 2
#define CONFIG_DIMM_SLOTS_PER_CTLR 2
#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_SYS_DDR2_CLK_CTRL 0x03800000
#define CONFIG_SYS_DDR2_CFG_1B 0xC3008008
-
#endif
/* #define CONFIG_ID_EEPROM 1
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#ifdef CONFIG_SYS_HUSH_PARSER
-#endif
-
-/*
- * Pass open firmware flat tree to kernel
- */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-
/*
* I2C
*/
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#undef CONFIG_SYS_SCSI_SCAN_BUS_REVERSE
-
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
#undef CONFIG_SCSI_AHCI
#ifdef CONFIG_SCSI_AHCI
/*
* Environment
*/
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000)
-#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k(one sector) for env */
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
- #define CONFIG_CMD_PCI
-#endif
-
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#if defined(CONFIG_CMD_KGDB)
- #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
- #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 1000000
-#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
-#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
-
-#define CONFIG_BAUDRATE 115200
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS0\0" \