#define CONFIG_MPC86xx 1 /* MPC86xx */
#define CONFIG_MPC8641 1 /* MPC8641 specific */
#define CONFIG_SBC8641D 1 /* SBC8641D board specific */
-#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */
+#define CONFIG_MP 1 /* support multiple processors */
#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
+#define CONFIG_SYS_TEXT_BASE 0xfff00000
+
#ifdef RUN_DIAG
-#define CFG_DIAG_ADDR 0xff800000
+#define CONFIG_SYS_DIAG_ADDR 0xff800000
#endif
-#define CFG_RESET_ADDRESS 0xfff00100
+#define CONFIG_SYS_RESET_ADDRESS 0xfff00100
+
+/*
+ * virtual address to be used for temporary mappings. There
+ * should be 128k free at this VA.
+ */
+#define CONFIG_SYS_SCRATCH_VA 0xe8000000
#define CONFIG_PCI 1 /* Enable PCIE */
-#define CONFIG_PCI1 1 /* PCIE controler 1 (slot 1) */
-#define CONFIG_PCI2 1 /* PCIE controler 2 (slot 2) */
+#define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */
+#define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */
#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
+#define CONFIG_BAT_RW 1 /* Use common BAT rw code */
#define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */
#undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup*/
/*
* L2CR setup -- make sure this is right for your board!
*/
-#define CFG_L2
+#define CONFIG_SYS_L2
#define L2_INIT 0
#define L2_ENABLE (L2CR_L2E)
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-#undef CFG_DRAM_TEST /* memory test, takes time */
-#define CFG_MEMTEST_START 0x00200000 /* memtest region */
-#define CFG_MEMTEST_END 0x00400000
+#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
+#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END 0x00400000
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CFG_CCSRBAR 0xf8000000 /* relocated CCSRBAR */
-#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR 0xf8000000 /* relocated CCSRBAR */
+#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
-#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000)
-#define CFG_PCI2_ADDR (CFG_CCSRBAR+0x9000)
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
+#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0
+#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR_PHYS_LOW
/*
* DDR Setup
*/
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
-#define CFG_DDR_SDRAM_BASE2 0x10000000 /* DDR bank 2 */
-#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
-#define CFG_SDRAM_BASE2 CFG_DDR_SDRAM_BASE2
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
+#define CONFIG_SYS_DDR_SDRAM_BASE2 0x10000000 /* DDR bank 2 */
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_SYS_SDRAM_BASE2 CONFIG_SYS_DDR_SDRAM_BASE2
+#define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */
#define CONFIG_VERY_BIG_RAM
-#define MPC86xx_DDR_SDRAM_CLK_CNTL
-
#define CONFIG_NUM_DDR_CONTROLLERS 2
#define CONFIG_DIMM_SLOTS_PER_CTLR 2
#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
* Manually set up DDR1 & DDR2 parameters
*/
- #define CFG_SDRAM_SIZE 512 /* DDR is 512MB */
-
- #define CFG_DDR_CS0_BNDS 0x0000000F
- #define CFG_DDR_CS1_BNDS 0x00000000
- #define CFG_DDR_CS2_BNDS 0x00000000
- #define CFG_DDR_CS3_BNDS 0x00000000
- #define CFG_DDR_CS0_CONFIG 0x80010102
- #define CFG_DDR_CS1_CONFIG 0x00000000
- #define CFG_DDR_CS2_CONFIG 0x00000000
- #define CFG_DDR_CS3_CONFIG 0x00000000
- #define CFG_DDR_TIMING_3 0x00000000
- #define CFG_DDR_TIMING_0 0x00220802
- #define CFG_DDR_TIMING_1 0x38377322
- #define CFG_DDR_TIMING_2 0x002040c7
- #define CFG_DDR_CFG_1A 0x43008008
- #define CFG_DDR_CFG_2 0x24401000
- #define CFG_DDR_MODE_1 0x23c00542
- #define CFG_DDR_MODE_2 0x00000000
- #define CFG_DDR_MODE_CTL 0x00000000
- #define CFG_DDR_INTERVAL 0x05080100
- #define CFG_DDR_DATA_INIT 0x00000000
- #define CFG_DDR_CLK_CTRL 0x03800000
- #define CFG_DDR_CFG_1B 0xC3008008
-
- #define CFG_DDR2_CS0_BNDS 0x0010001F
- #define CFG_DDR2_CS1_BNDS 0x00000000
- #define CFG_DDR2_CS2_BNDS 0x00000000
- #define CFG_DDR2_CS3_BNDS 0x00000000
- #define CFG_DDR2_CS0_CONFIG 0x80010102
- #define CFG_DDR2_CS1_CONFIG 0x00000000
- #define CFG_DDR2_CS2_CONFIG 0x00000000
- #define CFG_DDR2_CS3_CONFIG 0x00000000
- #define CFG_DDR2_EXT_REFRESH 0x00000000
- #define CFG_DDR2_TIMING_0 0x00220802
- #define CFG_DDR2_TIMING_1 0x38377322
- #define CFG_DDR2_TIMING_2 0x002040c7
- #define CFG_DDR2_CFG_1A 0x43008008
- #define CFG_DDR2_CFG_2 0x24401000
- #define CFG_DDR2_MODE_1 0x23c00542
- #define CFG_DDR2_MODE_2 0x00000000
- #define CFG_DDR2_MODE_CTL 0x00000000
- #define CFG_DDR2_INTERVAL 0x05080100
- #define CFG_DDR2_DATA_INIT 0x00000000
- #define CFG_DDR2_CLK_CTRL 0x03800000
- #define CFG_DDR2_CFG_1B 0xC3008008
+ #define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */
+
+ #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F
+ #define CONFIG_SYS_DDR_CS1_BNDS 0x00000000
+ #define CONFIG_SYS_DDR_CS2_BNDS 0x00000000
+ #define CONFIG_SYS_DDR_CS3_BNDS 0x00000000
+ #define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102
+ #define CONFIG_SYS_DDR_CS1_CONFIG 0x00000000
+ #define CONFIG_SYS_DDR_CS2_CONFIG 0x00000000
+ #define CONFIG_SYS_DDR_CS3_CONFIG 0x00000000
+ #define CONFIG_SYS_DDR_TIMING_3 0x00000000
+ #define CONFIG_SYS_DDR_TIMING_0 0x00220802
+ #define CONFIG_SYS_DDR_TIMING_1 0x38377322
+ #define CONFIG_SYS_DDR_TIMING_2 0x002040c7
+ #define CONFIG_SYS_DDR_CFG_1A 0x43008008
+ #define CONFIG_SYS_DDR_CFG_2 0x24401000
+ #define CONFIG_SYS_DDR_MODE_1 0x23c00542
+ #define CONFIG_SYS_DDR_MODE_2 0x00000000
+ #define CONFIG_SYS_DDR_MODE_CTL 0x00000000
+ #define CONFIG_SYS_DDR_INTERVAL 0x05080100
+ #define CONFIG_SYS_DDR_DATA_INIT 0x00000000
+ #define CONFIG_SYS_DDR_CLK_CTRL 0x03800000
+ #define CONFIG_SYS_DDR_CFG_1B 0xC3008008
+
+ #define CONFIG_SYS_DDR2_CS0_BNDS 0x0010001F
+ #define CONFIG_SYS_DDR2_CS1_BNDS 0x00000000
+ #define CONFIG_SYS_DDR2_CS2_BNDS 0x00000000
+ #define CONFIG_SYS_DDR2_CS3_BNDS 0x00000000
+ #define CONFIG_SYS_DDR2_CS0_CONFIG 0x80010102
+ #define CONFIG_SYS_DDR2_CS1_CONFIG 0x00000000
+ #define CONFIG_SYS_DDR2_CS2_CONFIG 0x00000000
+ #define CONFIG_SYS_DDR2_CS3_CONFIG 0x00000000
+ #define CONFIG_SYS_DDR2_EXT_REFRESH 0x00000000
+ #define CONFIG_SYS_DDR2_TIMING_0 0x00220802
+ #define CONFIG_SYS_DDR2_TIMING_1 0x38377322
+ #define CONFIG_SYS_DDR2_TIMING_2 0x002040c7
+ #define CONFIG_SYS_DDR2_CFG_1A 0x43008008
+ #define CONFIG_SYS_DDR2_CFG_2 0x24401000
+ #define CONFIG_SYS_DDR2_MODE_1 0x23c00542
+ #define CONFIG_SYS_DDR2_MODE_2 0x00000000
+ #define CONFIG_SYS_DDR2_MODE_CTL 0x00000000
+ #define CONFIG_SYS_DDR2_INTERVAL 0x05080100
+ #define CONFIG_SYS_DDR2_DATA_INIT 0x00000000
+ #define CONFIG_SYS_DDR2_CLK_CTRL 0x03800000
+ #define CONFIG_SYS_DDR2_CFG_1B 0xC3008008
#endif
/*
* The SBC8641D contains 16MB flash space at ff000000.
*/
-#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */
+#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */
/* Flash */
-#define CFG_BR0_PRELIM 0xff001001 /* port size 16bit */
-#define CFG_OR0_PRELIM 0xff006e65 /* 16MB Boot Flash area */
+#define CONFIG_SYS_BR0_PRELIM 0xff001001 /* port size 16bit */
+#define CONFIG_SYS_OR0_PRELIM 0xff006e65 /* 16MB Boot Flash area */
/* 64KB EEPROM */
-#define CFG_BR1_PRELIM 0xf0000801 /* port size 16bit */
-#define CFG_OR1_PRELIM 0xffff6e65 /* 64K EEPROM area */
+#define CONFIG_SYS_BR1_PRELIM 0xf0000801 /* port size 16bit */
+#define CONFIG_SYS_OR1_PRELIM 0xffff6e65 /* 64K EEPROM area */
/* EPLD - User switches, board id, LEDs */
-#define CFG_BR2_PRELIM 0xf1000801 /* port size 16bit */
-#define CFG_OR2_PRELIM 0xfff06e65 /* EPLD (switches, board ID, LEDs) area */
+#define CONFIG_SYS_BR2_PRELIM 0xf1000801 /* port size 16bit */
+#define CONFIG_SYS_OR2_PRELIM 0xfff06e65 /* EPLD (switches, board ID, LEDs) area */
/* Local bus SDRAM 128MB */
-#define CFG_BR3_PRELIM 0xe0001861 /* port size ?bit */
-#define CFG_OR3_PRELIM 0xfc006cc0 /* 128MB local bus SDRAM area (1st half) */
-#define CFG_BR4_PRELIM 0xe4001861 /* port size ?bit */
-#define CFG_OR4_PRELIM 0xfc006cc0 /* 128MB local bus SDRAM area (2nd half) */
+#define CONFIG_SYS_BR3_PRELIM 0xe0001861 /* port size ?bit */
+#define CONFIG_SYS_OR3_PRELIM 0xfc006cc0 /* 128MB local bus SDRAM area (1st half) */
+#define CONFIG_SYS_BR4_PRELIM 0xe4001861 /* port size ?bit */
+#define CONFIG_SYS_OR4_PRELIM 0xfc006cc0 /* 128MB local bus SDRAM area (2nd half) */
/* Disk on Chip (DOC) 128MB */
-#define CFG_BR5_PRELIM 0xe8001001 /* port size ?bit */
-#define CFG_OR5_PRELIM 0xf8006e65 /* 128MB local bus SDRAM area (2nd half) */
+#define CONFIG_SYS_BR5_PRELIM 0xe8001001 /* port size ?bit */
+#define CONFIG_SYS_OR5_PRELIM 0xf8006e65 /* 128MB local bus SDRAM area (2nd half) */
/* LCD */
-#define CFG_BR6_PRELIM 0xf4000801 /* port size ?bit */
-#define CFG_OR6_PRELIM 0xfff06e65 /* 128MB local bus SDRAM area (2nd half) */
+#define CONFIG_SYS_BR6_PRELIM 0xf4000801 /* port size ?bit */
+#define CONFIG_SYS_OR6_PRELIM 0xfff06e65 /* 128MB local bus SDRAM area (2nd half) */
/* Control logic & misc peripherals */
-#define CFG_BR7_PRELIM 0xf2000801 /* port size ?bit */
-#define CFG_OR7_PRELIM 0xfff06e65 /* 128MB local bus SDRAM area (2nd half) */
+#define CONFIG_SYS_BR7_PRELIM 0xf2000801 /* port size ?bit */
+#define CONFIG_SYS_OR7_PRELIM 0xfff06e65 /* 128MB local bus SDRAM area (2nd half) */
-#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_MAX_FLASH_SECT 131 /* sectors per device */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 131 /* sectors per device */
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */
#define CONFIG_FLASH_CFI_DRIVER
-#define CFG_FLASH_CFI
-#define CFG_WRITE_SWAPPED_DATA
-#define CFG_FLASH_EMPTY_INFO
-#define CFG_FLASH_PROTECTION
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_WRITE_SWAPPED_DATA
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_PROTECTION
#undef CONFIG_CLOCKS_IN_MHZ
-#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#ifndef CFG_INIT_RAM_LOCK
-#define CFG_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#ifndef CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */
#else
-#define CFG_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */
#endif
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
-#define CFG_NS16550_CLK get_bus_freq(0)
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
-#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
/* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
/*
#define CONFIG_OF_BOARD_SETUP 1
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-#define CFG_64BIT_VSPRINTF 1
-#define CFG_64BIT_STRTOUL 1
-
/*
* I2C
*/
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CFG_I2C_OFFSET 0x3100
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CONFIG_SYS_I2C_OFFSET 0x3100
/*
* RapidIO MMU
*/
-#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
-#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
-#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */
+#define CONFIG_SYS_RIO_MEM_BASE 0xc0000000 /* base address */
+#define CONFIG_SYS_RIO_MEM_PHYS CONFIG_SYS_RIO_MEM_BASE
+#define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 128M */
/*
* General PCI
* Addresses are mapped 1-1.
*/
-#define CFG_PCI1_MEM_BASE 0x80000000
-#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI1_IO_BASE 0xe2000000
-#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
-#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
-
-/* PCI view of System Memory */
-#define CFG_PCI_MEMORY_BUS 0x00000000
-#define CFG_PCI_MEMORY_PHYS 0x00000000
-#define CFG_PCI_MEMORY_SIZE 0x80000000
-
-#define CFG_PCI2_MEM_BASE 0xa0000000
-#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
-#define CFG_PCI2_MEM_SIZE 0x10000000 /* 256M */
-#define CFG_PCI2_IO_BASE 0xe3000000
-#define CFG_PCI2_IO_PHYS CFG_PCI2_IO_BASE
-#define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */
+#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS
+#define CONFIG_SYS_PCIE1_MEM_VIRT CONFIG_SYS_PCIE1_MEM_BUS
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE1_IO_BUS 0xe2000000
+#define CONFIG_SYS_PCIE1_IO_PHYS CONFIG_SYS_PCIE1_IO_BUS
+#define CONFIG_SYS_PCIE1_IO_VIRT CONFIG_SYS_PCIE1_IO_BUS
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x1000000 /* 16M */
+
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS
+#define CONFIG_SYS_PCIE2_MEM_VIRT CONFIG_SYS_PCIE2_MEM_BUS
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE2_IO_BUS 0xe3000000
+#define CONFIG_SYS_PCIE2_IO_PHYS CONFIG_SYS_PCIE2_IO_BUS
+#define CONFIG_SYS_PCIE2_IO_VIRT CONFIG_SYS_PCIE2_IO_BUS
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x1000000 /* 16M */
#if defined(CONFIG_PCI)
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#undef CFG_SCSI_SCAN_BUS_REVERSE
+#undef CONFIG_SYS_SCSI_SCAN_BUS_REVERSE
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#ifdef CONFIG_SCSI_AHCI
#define CONFIG_SATA_ULI5288
-#define CFG_SCSI_MAX_SCSI_ID 4
-#define CFG_SCSI_MAX_LUN 1
-#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
-#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4
+#define CONFIG_SYS_SCSI_MAX_LUN 1
+#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
+#define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE
#endif
#endif /* CONFIG_PCI */
#define TSEC3_FLAGS TSEC_GIGABIT
#define TSEC4_FLAGS TSEC_GIGABIT
-#define CFG_TBIPA_VALUE 0x1e /* Set TBI address not to conflict with TSEC1_PHY_ADDR */
+#define CONFIG_SYS_TBIPA_VALUE 0x1e /* Set TBI address not to conflict with TSEC1_PHY_ADDR */
#define CONFIG_ETHPRIME "eTSEC1"
* BAT0 2G Cacheable, non-guarded
* 0x0000_0000 2G DDR
*/
-#define CFG_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CFG_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP)
-#define CFG_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE )
-#define CFG_IBAT0U CFG_DBAT0U
+#define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE )
+#define CONFIG_SYS_IBAT0U CONFIG_SYS_DBAT0U
/*
* BAT1 1G Cache-inhibited, guarded
* 0xa000_0000 512M PCI-Express 2 Memory
* Changed it for operating from 0xd0000000
*/
-#define CFG_DBAT1L ( CFG_PCI1_MEM_BASE | BATL_PP_RW \
+#define CONFIG_SYS_DBAT1L ( CONFIG_SYS_PCIE1_MEM_PHYS | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT1U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_IBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT1U CFG_DBAT1U
+#define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCIE1_MEM_VIRT | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCIE1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U
/*
* BAT2 512M Cache-inhibited, guarded
* 0xc000_0000 512M RapidIO Memory
*/
-#define CFG_DBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW \
+#define CONFIG_SYS_DBAT2L (CONFIG_SYS_RIO_MEM_BASE | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT2U (CFG_RIO_MEM_BASE | BATU_BL_512M | BATU_VS | BATU_VP)
-#define CFG_IBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT2U CFG_DBAT2U
+#define CONFIG_SYS_DBAT2U (CONFIG_SYS_RIO_MEM_BASE | BATU_BL_512M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_RIO_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U
/*
* BAT3 4M Cache-inhibited, guarded
* 0xf800_0000 4M CCSR
*/
-#define CFG_DBAT3L ( CFG_CCSRBAR | BATL_PP_RW \
+#define CONFIG_SYS_DBAT3L ( CONFIG_SYS_CCSRBAR | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT3U (CFG_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP)
-#define CFG_IBAT3L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT3U CFG_DBAT3U
+#define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT3L (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U
+
+#if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
+#define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
+ | BATL_PP_RW | BATL_CACHEINHIBIT \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \
+ | BATU_BL_1M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
+ | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU
+#endif
/*
* BAT4 32M Cache-inhibited, guarded
* 0xe300_0000 16M PCI-Express 2 I/0
* Note that this is at 0xe0000000
*/
-#define CFG_DBAT4L ( CFG_PCI1_IO_BASE | BATL_PP_RW \
+#define CONFIG_SYS_DBAT4L ( CONFIG_SYS_PCIE1_IO_PHYS | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT4U (CFG_PCI1_IO_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
-#define CFG_IBAT4L (CFG_PCI1_IO_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT4U CFG_DBAT4U
+#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_VIRT | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCIE1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U
/*
* BAT5 128K Cacheable, non-guarded
* 0xe401_0000 128K Init RAM for stack in the CPU DCache (no backing memory)
*/
-#define CFG_DBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CFG_DBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-#define CFG_IBAT5L CFG_DBAT5L
-#define CFG_IBAT5U CFG_DBAT5U
+#define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L
+#define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U
/*
* BAT6 32M Cache-inhibited, guarded
* 0xfe00_0000 32M FLASH
*/
-#define CFG_DBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW \
+#define CONFIG_SYS_DBAT6L ((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT6U ((CFG_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP)
-#define CFG_IBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CFG_IBAT6U CFG_DBAT6U
-
-#define CFG_DBAT7L 0x00000000
-#define CFG_DBAT7U 0x00000000
-#define CFG_IBAT7L 0x00000000
-#define CFG_IBAT7U 0x00000000
+#define CONFIG_SYS_DBAT6U ((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT6L ((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U
+
+/* Map the last 1M of flash where we're running from reset */
+#define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
+ | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY
+
+#define CONFIG_SYS_DBAT7L 0x00000000
+#define CONFIG_SYS_DBAT7U 0x00000000
+#define CONFIG_SYS_IBAT7L 0x00000000
+#define CONFIG_SYS_IBAT7U 0x00000000
/*
* Environment
*/
#define CONFIG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
-#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
-#define CFG_ENV_SIZE 0x2000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000)
+#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#include <config_cmd_default.h>
#define CONFIG_CMD_PING
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_LOAD_ADDR 0x2000000 /* default load address */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
- #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
- #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
-#define CFG_CACHELINE_SIZE 32
+#define CONFIG_SYS_DCACHE_SIZE 32768
+#define CONFIG_SYS_CACHELINE_SIZE 32
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
+#define CONFIG_SYS_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
#endif
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */