Kconfig: Remove CONFIG_CLOCKS_IN_MHZ

[platform/kernel/u-boot.git] / include / configs / sbc8641d.h

diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h
index 5f0a955..5b93ccb 100644 (file)
--- a/include/configs/sbc8641d.h
+++ b/include/configs/sbc8641d.h
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2007 Wind River Systems <www.windriver.com>
  * Copyright 2007 Embedded Specialties, Inc.
@@ -6,8 +7,6 @@
  * Copyright 2006 Freescale Semiconductor.
  *
  * Srikanth Srinivasan (srikanth.srinivasan@freescale.com)
- *
- * SPDX-License-Identifier:    GPL-2.0+
  */
 
 /*
@@ -21,7 +20,6 @@
 #define __CONFIG_H
 
 /* High Level Configuration Options */
-#define CONFIG_MP              1       /* support multiple processors */
 #define CONFIG_LINUX_RESET_VEC  0x100   /* Reset vector used by Linux */
 
 #ifdef RUN_DIAG
@@ -47,7 +45,6 @@
 #define CONFIG_ENV_OVERWRITE
 
 #define CONFIG_BAT_RW          1       /* Use common BAT rw code */
-#define CONFIG_HIGH_BATS       1       /* High BATs supported and enabled */
 
 #undef CONFIG_SPD_EEPROM               /* Do not use SPD EEPROM for DDR setup*/
 #undef CONFIG_DDR_ECC                  /* only for ECC DDR module */
@@ -72,8 +69,6 @@
 #endif
 
 #undef CONFIG_SYS_DRAM_TEST                            /* memory test, takes time */
-#define CONFIG_SYS_MEMTEST_START       0x00200000      /* memtest region */
-#define CONFIG_SYS_MEMTEST_END         0x00400000
 
 /*
  * Base addresses -- Note these are effective addresses where the
@@ -208,13 +203,8 @@
 #define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE    /* start of monitor */
 #define CONFIG_SYS_MONITOR_BASE_EARLY   0xfff00000     /* early monitor loc */
 
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_WRITE_SWAPPED_DATA
 #define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_PROTECTION
-
-#undef CONFIG_CLOCKS_IN_MHZ
 
 #define CONFIG_SYS_INIT_RAM_LOCK       1
 #ifndef CONFIG_SYS_INIT_RAM_LOCK
@@ -284,7 +274,6 @@
 
 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 
-#undef CONFIG_EEPRO100
 #undef CONFIG_TULIP
 
 #if !defined(CONFIG_PCI_PNP)
@@ -300,15 +289,11 @@
 #define CONFIG_SYS_SCSI_MAX_SCSI_ID    4
 #define CONFIG_SYS_SCSI_MAX_LUN        1
 #define CONFIG_SYS_SCSI_MAX_DEVICE     (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
-#define CONFIG_SYS_SCSI_MAXDEVICE      CONFIG_SYS_SCSI_MAX_DEVICE
 #endif
 
 #endif /* CONFIG_PCI */
 
 #if defined(CONFIG_TSEC_ENET)
-
-/* #define CONFIG_MII          1 */    /* MII PHY management */
-
 #define CONFIG_TSEC1    1
 #define CONFIG_TSEC1_NAME       "eTSEC1"
 #define CONFIG_TSEC2    1
@@ -436,9 +421,6 @@
 /*
  * Environment
  */
-#define CONFIG_ENV_ADDR                (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_SECT_SIZE   0x20000 /* 128k(one sector) for env */
-#define CONFIG_ENV_SIZE                0x2000
 
 #define CONFIG_LOADS_ECHO      1       /* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   1       /* allow baudrate change */