+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2007 Wind River Systems <www.windriver.com>
* Copyright 2007 Embedded Specialties, Inc.
* Copyright 2006 Freescale Semiconductor.
*
* Srikanth Srinivasan (srikanth.srinivasan@freescale.com)
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
/*
#define __CONFIG_H
/* High Level Configuration Options */
-#define CONFIG_SBC8641D 1 /* SBC8641D board specific */
-#define CONFIG_MP 1 /* support multiple processors */
#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
-#define CONFIG_SYS_TEXT_BASE 0xfff00000
-
#ifdef RUN_DIAG
#define CONFIG_SYS_DIAG_ADDR 0xff800000
#endif
#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_BAT_RW 1 /* Use common BAT rw code */
-#define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */
#undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup*/
#undef CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_WRITE_SWAPPED_DATA
#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_PROTECTION
#undef CONFIG_CLOCKS_IN_MHZ
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
/* Serial Port */
-#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#undef CONFIG_SCSI_AHCI
-
#ifdef CONFIG_SCSI_AHCI
#define CONFIG_SATA_ULI5288
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4
#define CONFIG_SYS_SCSI_MAX_LUN 1
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
-#define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE
#endif
#endif /* CONFIG_PCI */
#if defined(CONFIG_TSEC_ENET)
-
-/* #define CONFIG_MII 1 */ /* MII PHY management */
-
#define CONFIG_TSEC1 1
#define CONFIG_TSEC1_NAME "eTSEC1"
#define CONFIG_TSEC2 1
/*
* Environment
*/
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k(one sector) for env */
-#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-
-#if defined(CONFIG_CMD_KGDB)
- #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
- #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
/*
* For booting Linux, the board info and command line data
#define CONFIG_IPADDR 192.168.0.50
-#define CONFIG_HOSTNAME sbc8641d
+#define CONFIG_HOSTNAME "sbc8641d"
#define CONFIG_ROOTPATH "/opt/eldk/ppc_74xx"
#define CONFIG_BOOTFILE "uImage"