* MA 02111-1307 USA
*/
-/* mpc8560ads board configuration file */
-/* please refer to doc/README.mpc85xx for more info */
+/* sbc8560 board configuration file */
+/* please refer to doc/README.sbc8560 for more info */
/* make sure you change the MAC address and other network params first,
* search for CONFIG_ETHADDR,CONFIG_SERVERIP,etc in this file
*/
#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
-#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
#define CFG_SDRAM_SIZE 512 /* DDR is 512MB */
-#define SPD_EEPROM_ADDRESS 0x55 /* DDR DIMM */
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
-#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
+/* DDR Setup */
+#define CONFIG_FSL_DDR1
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
+#undef CONFIG_DDR_SPD
#if defined(CONFIG_MPC85xx_REV1)
- #define CONFIG_DDR_DLL /* possible DLL fix needed */
+ #define CONFIG_DDR_DLL /* possible DLL fix needed */
#endif
+#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+
+#define CFG_DDR_SDRAM_BASE 0x00000000
+#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 2
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS 0x55 /* CTLR 0 DIMM 0 */
+
#undef CONFIG_CLOCKS_IN_MHZ
#if defined(CONFIG_RAM_AS_FLASH)
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+
/*
* I2C
*/
*/
#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
#if 0
#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
#define CFG_FLASH_PROTECTION /* use hardware protection */
/* Environment */
#if !defined(CFG_RAMBOOT)
#if defined(CONFIG_RAM_AS_FLASH)
- #define CFG_ENV_IS_NOWHERE
- #define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x100000)
- #define CFG_ENV_SIZE 0x2000
+ #define CONFIG_ENV_IS_NOWHERE
+ #define CONFIG_ENV_ADDR (CFG_FLASH_BASE + 0x100000)
+ #define CONFIG_ENV_SIZE 0x2000
#else
- #define CFG_ENV_IS_IN_FLASH 1
- #define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SECT_SIZE)
- #define CFG_ENV_SIZE 0x2000 /* CFG_ENV_SECT_SIZE */
+ #define CONFIG_ENV_IS_IN_FLASH 1
+ #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
+ #define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+ #define CONFIG_ENV_SIZE 0x2000 /* CONFIG_ENV_SECT_SIZE */
#endif
#else
#define CFG_NO_FLASH 1 /* Flash is not usable now */
- #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
- #define CFG_ENV_SIZE 0x2000
+ #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+ #define CONFIG_ENV_SIZE 0x2000
#endif
#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=dhcp console=ttyS0,9600"
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#if defined(CONFIG_CMD_KGDB)
- #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
- #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
#define CONFIG_HOSTNAME SBC8560
#define CONFIG_ROOTPATH /home/ppc
-#define CONFIG_BOOTFILE pImage
+#define CONFIG_BOOTFILE uImage
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=ramdisk.uboot\0" \
+ "fdtaddr=c00000\0" \
+ "fdtfile=sbc8560.dtb\0"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
#endif /* __CONFIG_H */