* This needs to be defined for the OHCI code to work but it is defined as
* ATMEL_ID_UHPHS in the CPU specific header files.
*/
-#define ATMEL_ID_UHP ATMEL_ID_UHPHS
+#define ATMEL_ID_UHP 32
/*
* Specify the clock enable bit in the PMC_SCER register.
*/
-#define ATMEL_PMC_UHP AT91SAM926x_PMC_UHP
+#define ATMEL_PMC_UHP (1 << 6)
/* LCD */
#define LCD_BPP LCD_COLOR16
#define CONFIG_LCD_LOGO
#define CONFIG_LCD_INFO
#define CONFIG_LCD_INFO_BELOW_LOGO
-#define CONFIG_SYS_WHITE_ON_BLACK
#define CONFIG_ATMEL_HLCD
#define CONFIG_ATMEL_LCD_RGB565
/* SDRAM */
#define CONFIG_NR_DRAM_BANKS 1
-#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS
+#define CONFIG_SYS_SDRAM_BASE 0x20000000
#define CONFIG_SYS_SDRAM_SIZE 0x20000000
#ifdef CONFIG_SPL_BUILD
#endif
/* NAND flash */
-#define CONFIG_CMD_NAND
-
#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_ATMEL
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3
+#define CONFIG_SYS_NAND_BASE 0x60000000
/* our ALE is AD21 */
#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
/* our CLE is AD22 */
#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
#define CONFIG_SYS_NAND_ONFI_DETECTION
+#endif
/* PMECC & PMERRLOC */
#define CONFIG_ATMEL_NAND_HWECC
#define CONFIG_ATMEL_NAND_HW_PMECC
#define CONFIG_PMECC_CAP 4
#define CONFIG_PMECC_SECTOR_SIZE 512
-#define CONFIG_CMD_NAND_TRIMFFS
-#endif
-
-#define CONFIG_PHY_MICREL_KSZ9021
/* USB */
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 3
#endif
-#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
-#define CONFIG_FAT_WRITE
-#endif
-
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
#ifdef CONFIG_SYS_USE_SERIALFLASH
/* override the bootcmd, bootargs and other configuration nandflash env */
#elif CONFIG_SYS_USE_MMC
/* override the bootcmd, bootargs and other configuration for sd/mmc env */
-#else
-#define CONFIG_ENV_IS_NOWHERE
#endif
/* SPL */
#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
-#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SYS_MONITOR_LEN (512 << 10)
#ifdef CONFIG_SYS_USE_MMC
-#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/armv7/u-boot-spl.lds
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"