+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Configuration file for the SAMA5D2 Xplained Board.
*
* Copyright (C) 2015 Atmel Corporation
* Wenyou Yang <wenyou.yang@atmel.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
-/* No NOR flash, this definition should put before common header */
-#define CONFIG_SYS_NO_FLASH
-
#include "at91-sama5_common.h"
-/* serial console */
-#define CONFIG_ATMEL_USART
-#define CONFIG_USART_BASE ATMEL_BASE_UART1
-#define CONFIG_USART_ID ATMEL_ID_UART1
-
/* SDRAM */
-#define CONFIG_NR_DRAM_BANKS 1
-#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS
+#define CONFIG_SYS_SDRAM_BASE 0x20000000
#define CONFIG_SYS_SDRAM_SIZE 0x20000000
#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_INIT_SP_ADDR 0x210000
+#define CONFIG_SYS_INIT_SP_ADDR 0x218000
#else
#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
+ (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
#endif
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
-#undef CONFIG_AT91_GPIO
-#define CONFIG_ATMEL_PIO4
-
/* SerialFlash */
-#ifdef CONFIG_CMD_SF
-#define CONFIG_ATMEL_SPI
-#define CONFIG_ATMEL_SPI0
-#define CONFIG_SPI_FLASH_ATMEL
-#define CONFIG_SF_DEFAULT_BUS 0
-#define CONFIG_SF_DEFAULT_CS 0
-#define CONFIG_SF_DEFAULT_SPEED 30000000
-#endif
-
-/* NAND flash */
-#undef CONFIG_CMD_NAND
-
-/* MMC */
-
-#ifdef CONFIG_CMD_MMC
-#define CONFIG_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_SDHCI
-#define CONFIG_ATMEL_SDHCI
-#define CONFIG_ATMEL_SDHCI0
-#define CONFIG_ATMEL_SDHCI1
-#define CONFIG_SUPPORT_EMMC_BOOT
-#endif
-/* USB */
+#ifdef CONFIG_SD_BOOT
-#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_ATMEL
-#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
-#endif
-
-/* USB device */
-#define CONFIG_USB_ETHER
-#define CONFIG_USB_ETH_RNDIS
-#define CONFIG_USBNET_MANUFACTURER "Atmel SAMA5D2 XPlained"
-
-#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
-#define CONFIG_DOS_PARTITION
-#endif
+/* bootstrap + u-boot + env in sd card */
+#undef CONFIG_BOOTCOMMAND
-/* Ethernet Hardware */
-#define CONFIG_MACB
-#define CONFIG_RMII
-#define CONFIG_NET_RETRY_COUNT 20
-#define CONFIG_MACB_SEARCH_PHY
-
-/* LCD */
-/* #define CONFIG_LCD */
-
-#ifdef CONFIG_LCD
-#define LCD_BPP LCD_COLOR16
-#define LCD_OUTPUT_BPP 24
-#define CONFIG_LCD_LOGO
-#define CONFIG_LCD_INFO
-#define CONFIG_LCD_INFO_BELOW_LOGO
-#define CONFIG_SYS_WHITE_ON_BLACK
-#define CONFIG_ATMEL_HLCD
-#define CONFIG_ATMEL_LCD_RGB565
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#endif
+#define CONFIG_BOOTCOMMAND "fatload mmc " CONFIG_ENV_FAT_DEVICE_AND_PART " 0x21000000 at91-sama5d2_xplained.dtb; " \
+ "fatload mmc " CONFIG_ENV_FAT_DEVICE_AND_PART " 0x22000000 zImage; " \
+ "bootz 0x22000000 - 0x21000000"
-#ifdef CONFIG_SYS_USE_MMC
+#elif CONFIG_SPI_BOOT
-/* bootstrap + u-boot + env in sd card */
-#undef FAT_ENV_DEVICE_AND_PART
+/* bootstrap + u-boot + env in sd card, but kernel + dtb in eMMC */
#undef CONFIG_BOOTCOMMAND
-#define FAT_ENV_DEVICE_AND_PART "1"
-#define CONFIG_BOOTCOMMAND "fatload mmc 1:1 0x21000000 at91-sama5d2_xplained.dtb; " \
- "fatload mmc 1:1 0x22000000 zImage; " \
+#define CONFIG_BOOTCOMMAND "ext4load mmc 0:1 0x21000000 /boot/at91-sama5d2_xplained.dtb; " \
+ "ext4load mmc 0:1 0x22000000 /boot/zImage; " \
"bootz 0x22000000 - 0x21000000"
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTARGS \
- "console=ttyS0,115200 earlyprintk root=/dev/mmcblk1p2 rw rootwait"
#endif
/* SPL */
-#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x200000
#define CONFIG_SPL_MAX_SIZE 0x10000
#define CONFIG_SPL_BSS_START_ADDR 0x20000000
#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
-#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SYS_MONITOR_LEN (512 << 10)
-#ifdef CONFIG_SYS_USE_MMC
-#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/armv7/u-boot-spl.lds
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
+#ifdef CONFIG_SD_BOOT
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
-#elif CONFIG_SYS_USE_SERIALFLASH
-#define CONFIG_SPL_SPI_SUPPORT
-#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8000
+#elif CONFIG_SPI_BOOT
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x10000
#endif