#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
#define CONFIG_SYS_AT91_MAIN_CLOCK 24000000 /* 24 MHz crystal */
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_SKIP_LOWLEVEL_INIT
-
#define CONFIG_USART_BASE ATMEL_BASE_DBGU
#define CONFIG_USART_ID 0 /* ignored in arm */
-/* general purpose I/O */
-#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
/*
* define CONFIG_USB_EHCI_HCD to enable USB Hi-Speed (aka 2.0)
* NB: in this case, USB 1.1 devices won't be recognized.
#define CONFIG_SYS_SDRAM_BASE 0x20000000
#define CONFIG_SYS_SDRAM_SIZE 0x10000000 /* 256 megs */
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
-
/* NAND flash */
#ifdef CONFIG_CMD_NAND
-#define CONFIG_NAND_ATMEL
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE 0x40000000
#define CONFIG_SYS_NAND_MASK_ALE BIT(21)
#define CONFIG_SYS_NAND_MASK_CLE BIT(22)
#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PD4
#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PD5
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
-#define CONFIG_MTD_DEVICE
-#endif
-
-/* PMECC & PMERRLOC */
-#define CONFIG_ATMEL_NAND_HWECC
-#define CONFIG_ATMEL_NAND_HW_PMECC
-#define CONFIG_PMECC_CAP 8
-#define CONFIG_PMECC_SECTOR_SIZE 512
-
-#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
-
-#ifdef CONFIG_SD_BOOT
-/* bootstrap + u-boot + env + linux in sd card */
-#define CONFIG_BOOTCOMMAND \
- "fatload mmc 0:1 0x21000000 at91-sam9x60ek.dtb;" \
- "fatload mmc 0:1 0x22000000 zImage;" \
- "bootz 0x22000000 - 0x21000000"
-
-#elif defined(CONFIG_NAND_BOOT)
-/* bootstrap + u-boot + env + linux in nandflash */
-#define CONFIG_BOOTCOMMAND "nand read " \
- "0x22000000 0x200000 0x600000; " \
- "nand read 0x21000000 0x180000 0x20000; " \
- "bootz 0x22000000 - 0x21000000"
-
-#elif defined(CONFIG_QSPI_BOOT)
-/* bootstrap + u-boot + env + linux in SPI NOR flash */
-#define CONFIG_BOOTCOMMAND "sf probe 0; " \
- "sf read 0x21000000 0x180000 0x80000; " \
- "sf read 0x22000000 0x200000 0x600000; " \
- "bootz 0x22000000 - 0x21000000"
#endif
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (512 * 1024 + 0x1000)
-
#endif