Merge https://source.denx.de/u-boot/custodians/u-boot-usb

[platform/kernel/u-boot.git] / include / configs / rut.h

diff --git a/include/configs/rut.h b/include/configs/rut.h
index e676a5a..ac48372 100644 (file)
--- a/include/configs/rut.h
+++ b/include/configs/rut.h
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * siemens rut
  * (C) Copyright 2013 Siemens Schweiz AG
@@ -7,16 +8,11 @@
  * U-Boot file:/include/configs/am335x_evm.h
  *
  * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
- *
- * SPDX-License-Identifier:    GPL-2.0+
  */
 
 #ifndef __CONFIG_RUT_H
 #define __CONFIG_RUT_H
 
-#define CONFIG_SIEMENS_RUT
-#define CONFIG_SIEMENS_MACH_TYPE       MACH_TYPE_RUT
-
 #include "siemens-am33x-common.h"
 
 #define RUT_IOCTRL_VAL 0x18b
@@ -25,25 +21,10 @@
  /* Physical Memory Map */
 #define CONFIG_MAX_RAM_BANK_SIZE       (256 << 20) /* 256 MiB */
 
-/* I2C Configuration */
-#define CONFIG_SYS_I2C_SPEED           100000
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR              0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       6       /* 64 byte pages */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* take up to 10 msec */
-
-#define CONFIG_PHY_NATSEMI
-
-#define CONFIG_FACTORYSET
-
 /* Watchdog */
 #define WATCHDOG_TRIGGER_GPIO  14
 
-#ifndef CONFIG_SPL_BUILD
-
 /* Use common default */
-#define MTDPARTS_DEFAULT       MTDPARTS_DEFAULT_V1
 
 /* Default env settings */
 #define CONFIG_EXTRA_ENV_SETTINGS \
@@ -76,55 +57,4 @@
                "bootm ${kloadaddr}\0" \
        ""
 
-#ifndef CONFIG_RESTORE_FLASH
-/* set to negative value for no autoboot */
-
-#define CONFIG_BOOTCOMMAND \
-       "if mmc rescan; then " \
-               "echo SD/MMC found on device ${mmc_dev};" \
-               "if run loadbootenv; then " \
-                       "echo Loaded environment from ${bootenv};" \
-                       "run importbootenv;" \
-               "fi;" \
-               "if test -n $uenvcmd; then " \
-                       "echo Running uenvcmd ...;" \
-                       "run uenvcmd;" \
-               "fi;" \
-               "if run mmc_load_uimage; then " \
-                       "run mmc_args;" \
-                       "bootm ${kloadaddr};" \
-               "fi;" \
-       "fi;" \
-       "run nand_boot;" \
-       "reset;"
-
-#else
-
-#define CONFIG_BOOTCOMMAND                     \
-       "setenv autoload no; "                  \
-       "dhcp; "                                \
-       "if tftp 80000000 debrick.scr; then "   \
-               "source 80000000; "             \
-       "fi"
-#endif
-
-#endif /* CONFIG_SPL_BUILD */
-
-#if defined(CONFIG_VIDEO)
-#define CONFIG_VIDEO_DA8XX
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_SPLASH_SCREEN_ALIGN
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_VIDEO_BMP_RLE8
-#define CONFIG_VIDEO_BMP_LOGO
-#define DA8XX_LCD_CNTL_BASE    LCD_CNTL_BASE
-
-#define CONFIG_SPI
-#define CONFIG_OMAP3_SPI
-
-#define BOARD_LCD_RESET                115     /* Bank 3 pin 19 */
-#define CONFIG_FORMIKE
-#define DISPL_PLL_SPREAD_SPECTRUM
-#endif
-
 #endif /* ! __CONFIG_RUT_H */