CONFIG_SYS_BAUDRATE_TABLE: Add <config_fallbacks.h>, place there

[platform/kernel/u-boot.git] / include / configs / r7780mp.h

diff --git a/include/configs/r7780mp.h b/include/configs/r7780mp.h
index 72a3b5c..a7b3628 100644 (file)
--- a/include/configs/r7780mp.h
+++ b/include/configs/r7780mp.h
@@ -60,6 +60,7 @@
 /* check for keypress on bootdelay==0 */
 /*#define CONFIG_ZERO_BOOTDELAY_CHECK*/
 
+#define CONFIG_SYS_TEXT_BASE           0x0FFC0000
 #define CONFIG_SYS_SDRAM_BASE          (0x08000000)
 #define CONFIG_SYS_SDRAM_SIZE          (128 * 1024 * 1024)
 
@@ -69,11 +70,9 @@
 #define CONFIG_SYS_PBSIZE              256
 #define CONFIG_SYS_MAXARGS             16
 #define CONFIG_SYS_BARGSIZE    512
-/* List of legal baudrate settings for this board */
-#define CONFIG_SYS_BAUDRATE_TABLE      { 115200, 57600, 38400, 19200, 9600 }
 
 #define CONFIG_SYS_MEMTEST_START       (CONFIG_SYS_SDRAM_BASE)
-#define CONFIG_SYS_MEMTEST_END         (TEXT_BASE - 0x100000)
+#define CONFIG_SYS_MEMTEST_END         (CONFIG_SYS_TEXT_BASE - 0x100000)
 
 /* Flash board support */
 #define CONFIG_SYS_FLASH_BASE          (0xA0000000)
@@ -100,8 +99,6 @@
 /* Size of DRAM reserved for malloc() use */
 #define CONFIG_SYS_MALLOC_LEN          (1204 * 1024)
 
-/* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_SIZE       (256)
 #define CONFIG_SYS_BOOTMAPSZ           (8 * 1024 * 1024)
 #define CONFIG_SYS_RX_ETH_BUFFER       (8)
 
@@ -121,14 +118,17 @@
 
 /* Board Clock */
 #define CONFIG_SYS_CLK_FREQ    33333333
-#define TMU_CLK_DIVIDER                4
-#define CONFIG_SYS_HZ  (CONFIG_SYS_CLK_FREQ / TMU_CLK_DIVIDER)
+#define CONFIG_SYS_TMU_CLK_DIV         4
+#define CONFIG_SYS_HZ          1000
 
 /* PCI Controller */
 #if defined(CONFIG_CMD_PCI)
 #define CONFIG_PCI
 #define CONFIG_SH4_PCI
 #define CONFIG_SH7780_PCI
+#define CONFIG_SH7780_PCI_LSR  0x07f00001
+#define CONFIG_SH7780_PCI_LAR  CONFIG_SYS_SDRAM_SIZE
+#define CONFIG_SH7780_PCI_BAR  CONFIG_SYS_SDRAM_SIZE
 #define CONFIG_PCI_PNP
 #define CONFIG_PCI_SCAN_SHOW   1
 #define __io
@@ -141,15 +141,16 @@
 #define CONFIG_PCI_IO_BUS      0xFE200000      /* IO space base address */
 #define CONFIG_PCI_IO_PHYS     CONFIG_PCI_IO_BUS
 #define CONFIG_PCI_IO_SIZE     0x00200000      /* Size of IO window */
+#define CONFIG_PCI_SYS_PHYS CONFIG_SYS_SDRAM_BASE
+#define CONFIG_PCI_SYS_BUS  CONFIG_SYS_SDRAM_BASE
+#define CONFIG_PCI_SYS_SIZE CONFIG_SYS_SDRAM_SIZE
 #endif /* CONFIG_CMD_PCI */
 
 #if defined(CONFIG_CMD_NET)
 /*
-#define CONFIG_NET_MULTI
 #define CONFIG_RTL8169
 */
-/* AX88696L Support(NE2000 base chip) */
-#define CONFIG_DRIVER_NE2000
+/* AX88796L Support(NE2000 base chip) */
 #define CONFIG_DRIVER_AX88796L
 #define CONFIG_DRIVER_NE2000_BASE      0xA4100000
 #endif
@@ -165,6 +166,7 @@
 #define CONFIG_SYS_ATA_DATA_OFFSET     0x1000          /* data reg offset */
 #define CONFIG_SYS_ATA_REG_OFFSET      0x1000          /* reg offset */
 #define CONFIG_SYS_ATA_ALT_OFFSET      0x800           /* alternate register offset */
+#define CONFIG_IDE_SWAP_IO
 #endif /* CONFIG_CMD_IDE */
 
 #endif /* __R7780RP_H */