#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/arch/mx31-regs.h>
+#include <asm/arch/imx-regs.h>
/* High Level Configuration Options */
#define CONFIG_ARM1136 1 /* This is an arm1136 CPU core */
/*
* Size of malloc() pool
*/
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024)
/* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_SIZE 128
/*
* Hardware drivers
#define CONFIG_MXC_UART 1
#define CONFIG_SYS_MX31_UART1 1
-#define CONFIG_MX31_GPIO
+#define CONFIG_MXC_GPIO
+#define CONFIG_HW_WATCHDOG
+
+#define CONFIG_MXC_SPI
+#define CONFIG_DEFAULT_SPI_BUS 1
+#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH)
+#define CONFIG_RTC_MC13783
+
+#define CONFIG_FSL_PMIC
+#define CONFIG_FSL_PMIC_BUS 1
+#define CONFIG_FSL_PMIC_CS 0
+#define CONFIG_FSL_PMIC_CLK 100000
+#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH)
/* FPGA */
+#define CONFIG_FPGA
#define CONFIG_QONG_FPGA 1
#define CONFIG_FPGA_BASE (CS1_BASE)
+#define CONFIG_FPGA_LATTICE
+#define CONFIG_FPGA_COUNT 1
#ifdef CONFIG_QONG_FPGA
/* Ethernet */
#define CONFIG_DNET_BASE (CS1_BASE + QONG_FPGA_PERIPH_SIZE)
#define CONFIG_NET_MULTI 1
+/* Framebuffer and LCD */
+#define CONFIG_LCD
+#define CONFIG_VIDEO_MX3
+#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define LCD_BPP LCD_COLOR16
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_CMD_BMP
+#define CONFIG_BMP_16BPP
+#define CONFIG_DISPLAY_COM57H5M10XRC
+
+/* USB */
+#define CONFIG_CMD_USB
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_MXC
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORT 2
+#define CONFIG_MXC_USB_PORTSC (MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT)
+#define CONFIG_MXC_USB_FLAGS MXC_EHCI_POWER_PINS_ENABLED
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#endif /* CONFIG_CMD_USB */
+
/*
* Reducing the ARP timeout from default 5 seconds to 200ms we speed up the
* initial TFTP transfer, should the user wish one, significantly.
#include <config_cmd_default.h>
-#define CONFIG_CMD_PING
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_NET
#define CONFIG_CMD_MII
-#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_SPI
-/*
- * You can compile in a MAC address and your custom net settings by using
- * the following syntax.
- *
- * #define CONFIG_ETHADDR xx:xx:xx:xx:xx:xx
- * #define CONFIG_SERVERIP <server ip>
- * #define CONFIG_IPADDR <board ip>
- * #define CONFIG_GATEWAYIP <gateway ip>
- * #define CONFIG_NETMASK <your netmask>
- */
+#define BOARD_LATE_INIT
#define CONFIG_BOOTDELAY 5
" console=ttymxc0,${baudrate}\0" \
"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
"addmisc=setenv bootargs ${bootargs}\0" \
- "uboot_addr=a0000000\0" \
- "kernel_addr=a0080000\0" \
- "ramdisk_addr=a0300000\0" \
+ "uboot_addr=A0000000\0" \
+ "kernel_addr=A00C0000\0" \
+ "ramdisk_addr=A0300000\0" \
"u-boot=qong/u-boot.bin\0" \
"kernel_addr_r=80800000\0" \
"hostname=qong\0" \
#define CONFIG_SYS_HZ 1000
#define CONFIG_CMDLINE_EDITING 1
+#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#endif
#define CONFIG_MISC_INIT_R 1
/*-----------------------------------------------------------------------
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_SECT_SIZE 0x20000
#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x40000)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x80000)
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#define CONFIG_SYS_FLASH_PROTECTION 1
/*
- * JFFS2 partitions
+ * Filesystem
*/
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_MTD_PARTITIONS
#define CONFIG_CMD_MTDPARTS
+#define CONFIG_LZO
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=physmap-flash.0"
+#define MTDIDS_DEFAULT "nor0=physmap-flash.0," \
+ "nand0=gen_nand"
#define MTDPARTS_DEFAULT \
- "mtdparts=physmap-flash.0:256k(U-Boot),128k(env1)," \
- "128k(env2),2560k(kernel),13m(ramdisk),-(user)"
+ "mtdparts=physmap-flash.0:" \
+ "512k(U-Boot),128k(env1),128k(env2)," \
+ "2304k(kernel),13m(ramdisk),-(user);" \
+ "gen_nand:" \
+ "128m(nand)"
+
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_SDRAM_BASE 0x80000000
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET)
+
+#define CONFIG_BOARD_EARLY_INIT_F 1
#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff