#define CONFIG_CMD_REGINFO
-/* High Level Configuration Options */
-#define CONFIG_BOOKE
-#define CONFIG_E500 /* BOOKE e500 family */
-#define CONFIG_QEMU_E500
-
#undef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0xf01000 /* 15 MB */
#define CONFIG_SYS_RAMBOOT
-#define CONFIG_PCI /* Enable PCI/PCIE */
#define CONFIG_PCI1 1 /* PCI controller 1 */
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/* Needed to fill the ccsrbar pointer */
-#define CONFIG_BOARD_EARLY_INIT_F
/* Virtual address to CCSRBAR */
#define CONFIG_SYS_CCSRBAR 0xe0000000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
#endif
-#define CONFIG_PHYS_64BIT
-
/* Virtual address range for PCI region maps */
#define CONFIG_SYS_PCI_MAP_START 0x80000000
#define CONFIG_SYS_PCI_MAP_END 0xe8000000
#define CONFIG_SYS_CLK_FREQ 33000000
-#define CONFIG_SYS_NO_FLASH
-
#define CONFIG_SYS_BOOT_BLOCK 0x00000000 /* boot TLB */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_ENV_IS_NOWHERE
-
#define CONFIG_HWCONFIG
#define CONFIG_SYS_INIT_RAM_ADDR 0x00100000
#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0))
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
-
/*
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0.
#ifdef CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
#endif /* CONFIG_PCI */
#define CONFIG_LBA48
-#define CONFIG_DOS_PARTITION
-#define CONFIG_CMD_EXT2
/*
* Environment
/*
* Command line configuration.
*/
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_BOOTZ
-#define CONFIG_CMD_GREPENV
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_PING
#ifdef CONFIG_PCI
#define CONFIG_CMD_PCI
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 1000000
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_BOOTDELAY 1
#define CONFIG_BOOTCOMMAND \
"test -n \"$qemu_kernel_addr\" && bootm $qemu_kernel_addr - $fdt_addr_r\0"