#ifndef __CONFIG_H
#define __CONFIG_H
+#define CONFIG_SYS_TEXT_BASE 0xfe000000
+
/*****************************************************************************
*
* These settings must match the way _your_ board is set up
* 0x6 0x1 66 133 266 Close Close Open
* 0x6 0x2 66 133 300 Close Open Close
*/
-#define CFG_PPMC_MODCK_H 0x05
+#define CONFIG_SYS_PPMC_MODCK_H 0x05
/* Define this if you want to boot from 0x00000100. If you don't define
* this, you will need to program the bootloader to 0xfff00000, and
* way to do that is to program the bootloader at both addresses.
* It is suggested that you just let U-Boot live at 0x00000000.
*/
-#define CFG_PPMC_BOOT_LOW 1
+#define CONFIG_SYS_PPMC_BOOT_LOW 1
/* What should the base address of the main FLASH be and how big is
- * it (in MBytes)? This must contain TEXT_BASE from board/ppmc8260/config.mk
+ * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE from board/ppmc8260/config.mk
* The main FLASH is whichever is connected to *CS0. U-Boot expects
* this to be the SIMM.
*/
-#define CFG_FLASH0_BASE 0xFE000000
-#define CFG_FLASH0_SIZE 16
+#define CONFIG_SYS_FLASH0_BASE 0xFE000000
+#define CONFIG_SYS_FLASH0_SIZE 16
/* What should be the base address of the first SDRAM DIMM and how big is
* it (in Mbytes)?
*/
-#define CFG_SDRAM0_BASE 0x00000000
-#define CFG_SDRAM0_SIZE 128
+#define CONFIG_SYS_SDRAM0_BASE 0x00000000
+#define CONFIG_SYS_SDRAM0_SIZE 128
/* What should be the base address of the second SDRAM DIMM and how big is
* it (in Mbytes)?
*/
-#define CFG_SDRAM1_BASE 0x08000000
-#define CFG_SDRAM1_SIZE 128
+#define CONFIG_SYS_SDRAM1_BASE 0x08000000
+#define CONFIG_SYS_SDRAM1_SIZE 128
/* What should be the base address of the on board SDRAM and how big is
* it (in Mbytes)?
*/
-#define CFG_SDRAM2_BASE 0x38000000
-#define CFG_SDRAM2_SIZE 16
+#define CONFIG_SYS_SDRAM2_BASE 0x38000000
+#define CONFIG_SYS_SDRAM2_SIZE 16
/* What should be the base address of the MAILBOX and how big is it
* (in Bytes)
- * The eeprom lives at CFG_MAILBOX_BASE + 0x80000000
+ * The eeprom lives at CONFIG_SYS_MAILBOX_BASE + 0x80000000
*/
-#define CFG_MAILBOX_BASE 0x32000000
-#define CFG_MAILBOX_SIZE 8192
+#define CONFIG_SYS_MAILBOX_BASE 0x32000000
+#define CONFIG_SYS_MAILBOX_SIZE 8192
/* What is the base address of the I/O select lines and how big is it
* (In Mbytes)?
*/
-#define CFG_IOSELECT_BASE 0xE0000000
-#define CFG_IOSELECT_SIZE 32
+#define CONFIG_SYS_IOSELECT_BASE 0xE0000000
+#define CONFIG_SYS_IOSELECT_SIZE 32
/* What should be the base address of the LEDs and switch S0?
* If you don't want them enabled, don't define this.
*/
-#define CFG_LED_BASE 0xF1000000
+#define CONFIG_SYS_LED_BASE 0xF1000000
/*
* PPMC8260 with 256 16 MB DIMM:
* Monitor Stack Buffer (0x80)
* 0x0FF5 FFB0 Board Info Data
* 0x0FF6 0000 Malloc Arena
- * : CFG_ENV_SECT_SIZE, 256k
- * : CFG_MALLOC_LEN, 128k
+ * : CONFIG_ENV_SECT_SIZE, 256k
+ * : CONFIG_SYS_MALLOC_LEN, 128k
* 0x0FFC 0000 RAM Copy of Monitor Code
- * : CFG_MONITOR_LEN, 256k
- * 0x0FFF FFFF [End of RAM], CFG_SDRAM_SIZE - 1
+ * : CONFIG_SYS_MONITOR_LEN, 256k
+ * 0x0FFF FFFF [End of RAM], CONFIG_SYS_SDRAM_SIZE - 1
*/
* for FCC)
*
* if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
- * from CONFIG_COMMANDS to remove support for networking.
+ * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
*/
#undef CONFIG_ETHER_ON_SCC /* define if ethernet on SCC */
* Port pins used for bit-banged MII communictions (if applicable).
*/
#define MDIO_PORT 2 /* Port C */
+#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \
+ (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
+#define MDC_DECLARE MDIO_DECLARE
+
#define MDIO_ACTIVE (iop->pdir |= 0x00400000)
#define MDIO_TRISTATE (iop->pdir &= ~0x00400000)
#define MDIO_READ ((iop->pdat & 0x00400000) != 0)
* put in the same sector as U-Boot, and changing variables
* will erase U-Boot temporarily
*/
-#define CFG_ENV_IN_OWN_SECT 1
+#define CONFIG_ENV_IN_OWN_SECT 1
/* Define to allow the user to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
* To stop use: " "
*/
# define CONFIG_AUTOBOOT_KEYED
-# define CONFIG_AUTOBOOT_PROMPT "Autobooting in %d seconds, press \" \" to stop\n"
+# define CONFIG_AUTOBOOT_PROMPT \
+ "Autobooting in %d seconds, press \" \" to stop\n", bootdelay
# define CONFIG_AUTOBOOT_STOP_STR " "
# undef CONFIG_AUTOBOOT_DELAY_STR
# define DEBUG_BOOTKEYS 0
/* Define a command string that is automatically executed when no character
* is read on the console interface withing "Boot Delay" after reset.
*/
-#undef CONFIG_BOOT_ROOT_INITRD /* Use ram disk for the root file system */
+#undef CONFIG_BOOT_ROOT_INITRD /* Use ram disk for the root file system */
#define CONFIG_BOOT_ROOT_NFS /* Use a NFS mounted root file system */
#ifdef CONFIG_BOOT_ROOT_INITRD
"bootm"
#endif /* CONFIG_BOOT_ROOT_NFS */
-/* Add support for a few extra bootp options like:
- * - File size
- * - DNS
+
+/*
+ * BOOTP options
*/
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
- CONFIG_BOOTP_BOOTFILESIZE | \
- CONFIG_BOOTP_DNS)
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_DNS
+
/* undef this to save memory */
-#define CFG_LONGHELP
+#define CONFIG_SYS_LONGHELP
/* Monitor Command Prompt */
-#define CFG_PROMPT "=> "
+#define CONFIG_SYS_PROMPT "=> "
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_IMMAP
-/* What U-Boot subsytems do you want enabled? */
-#define CONFIG_COMMANDS (((CONFIG_CMD_DFL & ~(CFG_CMD_KGDB))) | \
- CFG_CMD_ELF | \
- CFG_CMD_ASKENV | \
- CFG_CMD_REGINFO | \
- CFG_CMD_MEMTEST | \
- CFG_CMD_MII | \
- CFG_CMD_IMMAP)
+#undef CONFIG_CMD_KGDB
/* Where do the internal registers live? */
-#define CFG_IMMR 0xf0000000
+#define CONFIG_SYS_IMMR 0xf0000000
/*****************************************************************************
*
#define CONFIG_PPMC8260 1 /* on an Wind River PPMC8260 Board */
#define CONFIG_CPM2 1 /* Has a CPM2 */
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
/*
* Miscellaneous configurable options
*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#if defined(CONFIG_CMD_KGDB)
+# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-# define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
/* Print Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT)+16)
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
-#define CFG_MAXARGS 32 /* max number of command args */
+#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_LOAD_ADDR 0x140000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_LOAD_ADDR 0x140000 /* default load address */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CFG_MEMTEST_START 0x2000 /* memtest works from the end of */
+#define CONFIG_SYS_MEMTEST_START 0x2000 /* memtest works from the end of */
/* the exception vector table */
/* to the end of the DRAM */
/* less monitor and malloc area */
-#define CFG_STACK_USAGE 0x10000 /* Reserve 64k for the stack usage */
-#define CFG_MEM_END_USAGE ( CFG_MONITOR_LEN \
- + CFG_MALLOC_LEN \
- + CFG_ENV_SECT_SIZE \
- + CFG_STACK_USAGE )
+#define CONFIG_SYS_STACK_USAGE 0x10000 /* Reserve 64k for the stack usage */
+#define CONFIG_SYS_MEM_END_USAGE ( CONFIG_SYS_MONITOR_LEN \
+ + CONFIG_SYS_MALLOC_LEN \
+ + CONFIG_ENV_SECT_SIZE \
+ + CONFIG_SYS_STACK_USAGE )
-#define CFG_MEMTEST_END ( CFG_SDRAM_SIZE * 1024 * 1024 \
- - CFG_MEM_END_USAGE )
+#define CONFIG_SYS_MEMTEST_END ( CONFIG_SYS_SDRAM_SIZE * 1024 * 1024 \
+ - CONFIG_SYS_MEM_END_USAGE )
/* valid baudrates */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
* Low Level Configuration Settings
* - RX clk is CLK11
* - TX clk is CLK12
*/
-#define CFG_CMXSCR_VALUE (CMXSCR_RS1CS_CLK11 |\
+#define CONFIG_SYS_CMXSCR_VALUE (CMXSCR_RS1CS_CLK11 |\
CMXSCR_TS1CS_CLK12)
#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2)
* - Select bus for bd/buffers (see 28-13)
* - Enable Full Duplex in FSMR
*/
-#define CFG_CMXFCR_MASK (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
-#define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
-#define CFG_CPMFCR_RAMTYPE 0
-#define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
+#define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
+#define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
+#define CONFIG_SYS_CPMFCR_RAMTYPE 0
+#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
#endif /* CONFIG_ETHER_INDEX */
-#define CFG_FLASH_BASE CFG_FLASH0_BASE
-#define CFG_FLASH_SIZE CFG_FLASH0_SIZE
-#define CFG_SDRAM_BASE CFG_SDRAM0_BASE
-#define CFG_SDRAM_SIZE (CFG_SDRAM0_SIZE + CFG_SDRAM1_SIZE)
+#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE
+#define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM0_BASE
+#define CONFIG_SYS_SDRAM_SIZE (CONFIG_SYS_SDRAM0_SIZE + CONFIG_SYS_SDRAM1_SIZE)
/*-----------------------------------------------------------------------
* Hard Reset Configuration Words
*/
-#if defined(CFG_PPMC_BOOT_LOW)
-# define CFG_PPMC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS)
+#if defined(CONFIG_SYS_PPMC_BOOT_LOW)
+# define CONFIG_SYS_PPMC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS)
#else
-# define CFG_PPMC_HRCW_BOOT_FLAGS (0)
-#endif /* defined(CFG_PPMC_BOOT_LOW) */
+# define CONFIG_SYS_PPMC_HRCW_BOOT_FLAGS (0)
+#endif /* defined(CONFIG_SYS_PPMC_BOOT_LOW) */
-/* get the HRCW ISB field from CFG_IMMR */
-#define CFG_PPMC_HRCW_IMMR ( ((CFG_IMMR & 0x10000000) >> 10) | \
- ((CFG_IMMR & 0x01000000) >> 7) | \
- ((CFG_IMMR & 0x00100000) >> 4) )
+/* get the HRCW ISB field from CONFIG_SYS_IMMR */
+#define CONFIG_SYS_PPMC_HRCW_IMMR ( ((CONFIG_SYS_IMMR & 0x10000000) >> 10) | \
+ ((CONFIG_SYS_IMMR & 0x01000000) >> 7) | \
+ ((CONFIG_SYS_IMMR & 0x00100000) >> 4) )
-#define CFG_HRCW_MASTER ( HRCW_EBM | \
+#define CONFIG_SYS_HRCW_MASTER ( HRCW_EBM | \
HRCW_BPS11 | \
HRCW_L2CPC10 | \
HRCW_DPPC00 | \
- CFG_PPMC_HRCW_IMMR | \
+ CONFIG_SYS_PPMC_HRCW_IMMR | \
HRCW_MMR00 | \
HRCW_LBPC00 | \
HRCW_APPC10 | \
HRCW_CS10PC00 | \
- (CFG_PPMC_MODCK_H & HRCW_MODCK_H1111) | \
- CFG_PPMC_HRCW_BOOT_FLAGS )
+ (CONFIG_SYS_PPMC_MODCK_H & HRCW_MODCK_H1111) | \
+ CONFIG_SYS_PPMC_HRCW_BOOT_FLAGS )
/* no slaves */
-#define CFG_HRCW_SLAVE1 0
-#define CFG_HRCW_SLAVE2 0
-#define CFG_HRCW_SLAVE3 0
-#define CFG_HRCW_SLAVE4 0
-#define CFG_HRCW_SLAVE5 0
-#define CFG_HRCW_SLAVE6 0
-#define CFG_HRCW_SLAVE7 0
+#define CONFIG_SYS_HRCW_SLAVE1 0
+#define CONFIG_SYS_HRCW_SLAVE2 0
+#define CONFIG_SYS_HRCW_SLAVE3 0
+#define CONFIG_SYS_HRCW_SLAVE4 0
+#define CONFIG_SYS_HRCW_SLAVE5 0
+#define CONFIG_SYS_HRCW_SLAVE6 0
+#define CONFIG_SYS_HRCW_SLAVE7 0
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 128 /* bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
- * Note also that the logic that sets CFG_RAMBOOT is platform dependent.
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ * Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependent.
*/
-#define CFG_MONITOR_BASE CFG_FLASH0_BASE
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH0_BASE
-#ifndef CFG_MONITOR_BASE
-#define CFG_MONITOR_BASE 0x0ff80000
+#ifndef CONFIG_SYS_MONITOR_BASE
+#define CONFIG_SYS_MONITOR_BASE 0x0ff80000
#endif
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-# define CFG_RAMBOOT
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+# define CONFIG_SYS_RAMBOOT
#endif
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 374 kB for Monitor */
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 374 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
-#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_FLASH_INCREMENT 0 /* there is only one bank */
-#define CFG_FLASH_PROTECTION 1 /* use hardware protection */
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_FLASH_INCREMENT 0 /* there is only one bank */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware protection */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#ifndef CFG_RAMBOOT
+#ifndef CONFIG_SYS_RAMBOOT
-# define CFG_ENV_IS_IN_FLASH 1
-# ifdef CFG_ENV_IN_OWN_SECT
-# define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
-# define CFG_ENV_SECT_SIZE 0x40000
+# define CONFIG_ENV_IS_IN_FLASH 1
+# ifdef CONFIG_ENV_IN_OWN_SECT
+# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000)
+# define CONFIG_ENV_SECT_SIZE 0x40000
# else
-# define CFG_ENV_ADDR (CFG_FLASH_BASE + CFG_MONITOR_LEN - CFG_ENV_SECT_SIZE)
-# define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
-# define CFG_ENV_SECT_SIZE 0x40000 /* see README - env sect real size */
-# endif /* CFG_ENV_IN_OWN_SECT */
+# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_ENV_SECT_SIZE)
+# define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
+# define CONFIG_ENV_SECT_SIZE 0x40000 /* see README - env sect real size */
+# endif /* CONFIG_ENV_IN_OWN_SECT */
#else
-# define CFG_ENV_IS_IN_FLASH 1
-# define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x40000)
-#define CFG_ENV_SIZE 0x1000
-# define CFG_ENV_SECT_SIZE 0x40000
-#endif /* CFG_RAMBOOT */
+# define CONFIG_ENV_IS_IN_FLASH 1
+# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x40000)
+#define CONFIG_ENV_SIZE 0x1000
+# define CONFIG_ENV_SECT_SIZE 0x40000
+#endif /* CONFIG_SYS_RAMBOOT */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#if defined(CONFIG_CMD_KGDB)
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
*
* HID1 has only read-only information - nothing to set.
*/
-#define CFG_HID0_INIT (HID0_ICE |\
+#define CONFIG_SYS_HID0_INIT (HID0_ICE |\
HID0_DCE |\
HID0_ICFI |\
HID0_DCI |\
HID0_IFEM |\
HID0_ABE)
-#define CFG_HID0_FINAL (HID0_ICE |\
+#define CONFIG_SYS_HID0_FINAL (HID0_ICE |\
HID0_IFEM |\
HID0_ABE |\
HID0_EMCP)
-#define CFG_HID2 0
+#define CONFIG_SYS_HID2 0
/*-----------------------------------------------------------------------
* RMR - Reset Mode Register
*-----------------------------------------------------------------------
*/
-#define CFG_RMR 0
+#define CONFIG_SYS_RMR 0
/*-----------------------------------------------------------------------
* BCR - Bus Configuration 4-25
*-----------------------------------------------------------------------
*/
-#define CFG_BCR (BCR_EBM |\
+#define CONFIG_SYS_BCR (BCR_EBM |\
0x30000000)
/*-----------------------------------------------------------------------
*-----------------------------------------------------------------------
*/
-#define CFG_SIUMCR (SIUMCR_ESE |\
+#define CONFIG_SYS_SIUMCR (SIUMCR_ESE |\
SIUMCR_DPPC00 |\
SIUMCR_L2CPC10 |\
SIUMCR_LBPC00 |\
*-----------------------------------------------------------------------
* Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
*/
-#define CFG_SYPCR (SYPCR_SWTC |\
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\
SYPCR_BMT |\
SYPCR_PBME |\
SYPCR_LBME |\
* Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
* and enable Time Counter
*/
-#define CFG_TMCNTSC (TMCNTSC_SEC |\
+#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC |\
TMCNTSC_ALR |\
TMCNTSC_TCF |\
TMCNTSC_TCE)
* Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
* Periodic timer
*/
-#define CFG_PISCR (PISCR_PS |\
+#define CONFIG_SYS_PISCR (PISCR_PS |\
PISCR_PTF |\
PISCR_PTE)
* SCCR - System Clock Control 9-8
*-----------------------------------------------------------------------
*/
-#define CFG_SCCR 0
+#define CONFIG_SYS_SCCR 0
/*-----------------------------------------------------------------------
* RCCR - RISC Controller Configuration 13-7
*-----------------------------------------------------------------------
*/
-#define CFG_RCCR 0
+#define CONFIG_SYS_RCCR 0
/*
* Initialize Memory Controller:
* - No data pipelining is done
* - Valid
*/
-#define CFG_BR0_PRELIM ((CFG_FLASH0_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH0_BASE & BRx_BA_MSK) |\
BRx_PS_32 |\
BRx_MS_GPCM_P |\
BRx_V)
* - One idle clock is inserted between a read access from the
* current bank and the next access.
*/
-#define CFG_OR0_PRELIM (MEG_TO_AM(CFG_FLASH0_SIZE) |\
+#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH0_SIZE) |\
ORxG_CSNT |\
ORxG_ACS_DIV1 |\
ORxG_SCY_5_CLK |\
* - No data pipelining is done
* - Valid
*/
-#define CFG_BR2_PRELIM ((CFG_SDRAM0_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) |\
BRx_PS_64 |\
BRx_MS_SDRAM_P |\
BRx_V)
-#define CFG_BR3_PRELIM ((CFG_SDRAM1_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_SDRAM1_BASE & BRx_BA_MSK) |\
BRx_PS_64 |\
BRx_MS_SDRAM_P |\
BRx_V)
* - Internal bank interleaving within save device enabled
*/
-#define CFG_OR2_PRELIM (MEG_TO_AM(CFG_SDRAM0_SIZE) |\
+#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM0_SIZE) |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI0_A7 |\
ORxS_NUMR_13)
-#define CFG_OR3_PRELIM (MEG_TO_AM(CFG_SDRAM1_SIZE) |\
+#define CONFIG_SYS_OR3_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM1_SIZE) |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI0_A7 |\
ORxS_NUMR_13)
* - External Address Multiplexing enabled
* - CAS Latency is 2.
*/
-#define CFG_PSDMR (PSDMR_RFEN |\
+#define CONFIG_SYS_PSDMR (PSDMR_RFEN |\
PSDMR_SDAM_A14_IS_A5 |\
PSDMR_BSMA_A13_A15 |\
PSDMR_SDA10_PBI0_A9 |\
PSDMR_CL_2)
-#define CFG_PSRT 0x0e
-#define CFG_MPTPR MPTPR_PTP_DIV32
+#define CONFIG_SYS_PSRT 0x0e
+#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV32
/*-----------------------------------------------------------------------
*
*/
-#define CFG_BR4_PRELIM ((CFG_SDRAM2_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_SDRAM2_BASE & BRx_BA_MSK) |\
BRx_PS_32 |\
BRx_DECC_NONE |\
BRx_MS_SDRAM_L |\
* - Internal bank interleaving within save device enabled
*/
-#define CFG_OR4_PRELIM (MEG_TO_AM(CFG_SDRAM2_SIZE) |\
+#define CONFIG_SYS_OR4_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM2_SIZE) |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI0_A10 |\
ORxS_NUMR_12)
* - External Address Multiplexing disabled
* - CAS Latency is 2.
*/
-#define CFG_LSDMR (PSDMR_RFEN |\
+#define CONFIG_SYS_LSDMR (PSDMR_RFEN |\
PSDMR_SDAM_A13_IS_A5 |\
PSDMR_BSMA_A15_A17 |\
PSDMR_SDA10_PBI0_A11 |\
PSDMR_WRC_1C |\
PSDMR_CL_2)
-#define CFG_LSRT 0x0e
+#define CONFIG_SYS_LSRT 0x0e
/*-----------------------------------------------------------------------
* BR5 - Base Register
* - Valid
*/
-#define CFG_BR5_PRELIM ((CFG_MAILBOX_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_MAILBOX_BASE & BRx_BA_MSK) |\
BRx_PS_8 |\
BRx_DECC_NONE |\
BRx_MS_GPCM_P |\
* current bank and the next access.
*/
-#define CFG_OR5_PRELIM ((P2SZ_TO_AM(CFG_MAILBOX_SIZE) & ~0x80000000) |\
+#define CONFIG_SYS_OR5_PRELIM ((P2SZ_TO_AM(CONFIG_SYS_MAILBOX_SIZE) & ~0x80000000) |\
ORxG_ACS_DIV2 |\
ORxG_SCY_15_CLK |\
ORxG_TRLX |\
* - No data pipelining is done
* - Valid
*/
-#define CFG_BR6_PRELIM ((CFG_IOSELECT_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR6_PRELIM ((CONFIG_SYS_IOSELECT_BASE & BRx_BA_MSK) |\
BRx_PS_16 |\
BRx_MS_GPCM_P |\
BRx_V)
* current bank and the next access.
*/
-#define CFG_OR6_PRELIM (MEG_TO_AM(CFG_IOSELECT_SIZE) |\
+#define CONFIG_SYS_OR6_PRELIM (MEG_TO_AM(CONFIG_SYS_IOSELECT_SIZE) |\
ORxG_ACS_DIV2 |\
ORxG_SCY_15_CLK |\
ORxG_TRLX |\
* LEDs are at 0x00001 (write only)
* switches are at 0x00001 (read only)
*/
-#ifdef CFG_LED_BASE
+#ifdef CONFIG_SYS_LED_BASE
/* BR7 is configured as follows:
*
* - No data pipelining is done
* - Valid
*/
-#define CFG_BR7_PRELIM ((CFG_LED_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR7_PRELIM ((CONFIG_SYS_LED_BASE & BRx_BA_MSK) |\
BRx_PS_8 |\
BRx_DECC_NONE |\
BRx_MS_GPCM_P |\
* - One idle clock is inserted between a read access from the
* current bank and the next access.
*/
-#define CFG_OR7_PRELIM (ORxG_AM_MSK |\
+#define CONFIG_SYS_OR7_PRELIM (ORxG_AM_MSK |\
ORxG_CSNT |\
ORxG_ACS_DIV1 |\
ORxG_SCY_15_CLK |\
ORxG_TRLX |\
ORxG_EHTR)
-#endif /* CFG_LED_BASE */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
+#endif /* CONFIG_SYS_LED_BASE */
#endif /* __CONFIG_H */