+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2010
* Ilko Iliev <iliev@ronetix.at>
* Lead Tech Design <www.leadtechdesign.com>
*
* Configuation settings for the PM9G45 board.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
-/*
- * SoC must be defined first, before hardware.h is included.
- * In this case SoC is defined in boards.cfg.
- */
-#include <asm/hardware.h>
-
-#define CONFIG_PM9G45 1 /* It's an Ronetix PM9G45 */
-#define CONFIG_SYS_AT91_CPU_NAME "AT91SAM9G45"
-
-#define MACH_TYPE_PM9G45 2672
-#define CONFIG_MACH_TYPE MACH_TYPE_PM9G45
-
/* ARM asynchronous clock */
-#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
-#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */
-#define CONFIG_SYS_TEXT_BASE 0x73f00000
-
-#define CONFIG_ARCH_CPU_INIT
-
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
-
-#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_BOARD_EARLY_INIT_F
-
-/*
- * Hardware drivers
- */
-#define CONFIG_AT91_GPIO 1
-#define CONFIG_ATMEL_USART 1
-#define CONFIG_USART_BASE ATMEL_BASE_DBGU
-#define CONFIG_USART_ID ATMEL_ID_SYS
-
-#define CONFIG_SYS_USE_NANDFLASH 1
-
-/* LED */
-#define CONFIG_AT91_LED
-#define CONFIG_RED_LED AT91_PIO_PORTD, 31 /* this is the user1 led */
-#define CONFIG_GREEN_LED AT91_PIO_PORTD, 0 /* this is the user2 led */
-
-#define CONFIG_BOOTDELAY 3
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE 1
-#define CONFIG_BOOTP_BOOTPATH 1
-#define CONFIG_BOOTP_GATEWAY 1
-#define CONFIG_BOOTP_HOSTNAME 1
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_IMLS
-
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_PING 1
-#define CONFIG_CMD_DHCP 1
-#define CONFIG_CMD_NAND 1
-#define CONFIG_CMD_USB 1
-
-#define CONFIG_CMD_JFFS2 1
-#define CONFIG_JFFS2_CMDLINE 1
-#define CONFIG_JFFS2_NAND 1
-#define CONFIG_JFFS2_DEV "nand0" /* NAND dev jffs2 lives on */
-#define CONFIG_JFFS2_PART_OFFSET 0 /* start of jffs2 partition */
-#define CONFIG_JFFS2_PART_SIZE (256 * 1024 * 1024) /* partition */
+#define CFG_SYS_AT91_SLOW_CLOCK 32768
+#define CFG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
/* SDRAM */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM 0x70000000
-#define PHYS_SDRAM_SIZE 0x08000000 /* 128 megs */
-
-/* NOR flash, not available */
-#define CONFIG_SYS_NO_FLASH 1
-#undef CONFIG_CMD_FLASH
+#define CFG_SYS_SDRAM_BASE 0x70000000
+#define CFG_SYS_SDRAM_SIZE 0x08000000
/* NAND flash */
#ifdef CONFIG_CMD_NAND
-#define CONFIG_NAND_ATMEL
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE 0x40000000
-#define CONFIG_SYS_NAND_DBW_8 1
+#define CFG_SYS_NAND_BASE ATMEL_BASE_CS3
/* our ALE is AD21 */
-#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
+#define CFG_SYS_NAND_MASK_ALE BIT(21)
/* our CLE is AD22 */
-#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
-#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIO_PORTC, 14
-#define CONFIG_SYS_NAND_READY_PIN AT91_PIO_PORTD, 3
-
+#define CFG_SYS_NAND_MASK_CLE BIT(22)
+#define CFG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14
+#define CFG_SYS_NAND_READY_PIN AT91_PIN_PD3
#endif
-/* Ethernet */
-#define CONFIG_MACB 1
-#define CONFIG_RMII 1
-#define CONFIG_NET_RETRY_COUNT 20
-#define CONFIG_RESET_PHY_R 1
-
-/* USB */
-#define CONFIG_USB_ATMEL
-#define CONFIG_USB_OHCI_NEW 1
-#define CONFIG_DOS_PARTITION 1
-#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
-#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00700000 /* _UHP_OHCI_BASE */
-#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9g45"
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
-#define CONFIG_USB_STORAGE 1
-
-/* board specific(not enough SRAM) */
-#define CONFIG_AT91SAM9G45_LCD_BASE PHYS_SDRAM + 0xE00000
-
-#define CONFIG_SYS_LOAD_ADDR PHYS_SDRAM + 0x2000000 /* load addr */
-
-#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
-#define CONFIG_SYS_MEMTEST_END CONFIG_AT91SAM9G45_LCD_BASE
-
-/* bootstrap + u-boot + env + linux in nandflash */
-#define CONFIG_ENV_IS_IN_NAND 1
-#define CONFIG_ENV_OFFSET 0x60000
-#define CONFIG_ENV_OFFSET_REDUND 0x80000
-#define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */
-#define CONFIG_BOOTCOMMAND "nand read 0x72000000 0x200000 0x200000; bootm"
-#define CONFIG_BOOTARGS "fbcon=rotate:3 console=tty0 " \
- "console=ttyS0,115200 " \
- "root=/dev/mtdblock4 " \
- "mtdparts=atmel_nand:128k(bootstrap)ro," \
- "256k(uboot)ro,1664k(env)," \
- "2M(linux)ro,-(root) rw " \
- "rootfstype=jffs2"
+#ifdef CONFIG_NAND_BOOT
+/* bootstrap + u-boot + env in nandflash */
+#elif CONFIG_SD_BOOT
+/* bootstrap + u-boot + env + linux in mmc */
+#endif
-#define CONFIG_BAUDRATE 115200
+/* Defines for SPL */
-#define CONFIG_SYS_PROMPT "U-Boot> "
-#define CONFIG_SYS_CBSIZE 256
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP 1
-#define CONFIG_CMDLINE_EDITING 1
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SD_BOOT
+#elif CONFIG_NAND_BOOT
+#define CFG_SYS_NAND_U_BOOT_SIZE 0x80000
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024,\
- 0x1000)
+#define CFG_SYS_NAND_ECCSIZE 256
+#define CFG_SYS_NAND_ECCBYTES 3
+#define CFG_SYS_NAND_ECCPOS { 40, 41, 42, 43, 44, 45, 46, 47, \
+ 48, 49, 50, 51, 52, 53, 54, 55, \
+ 56, 57, 58, 59, 60, 61, 62, 63, }
+#endif
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - \
- GENERATED_GBL_DATA_SIZE)
+#define CFG_SYS_MASTER_CLOCK 132096000
+#define CFG_SYS_AT91_PLLA 0x20c73f03
+#define CFG_SYS_MCKR 0x1301
+#define CFG_SYS_MCKR_CSS 0x1302
#endif