Rename CONFIG_EHCI_IS_TDI to CONFIG_USB_EHCI_IS_TDI

[platform/kernel/u-boot.git] / include / configs / pico-imx8mq.h

diff --git a/include/configs/pico-imx8mq.h b/include/configs/pico-imx8mq.h
index da28429..d858a7e 100644 (file)
--- a/include/configs/pico-imx8mq.h
+++ b/include/configs/pico-imx8mq.h
@@ -13,20 +13,19 @@
 #define CONFIG_SYS_MONITOR_LEN         (512 * 1024)
 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR        0x300
-#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION     1
 
 #ifdef CONFIG_SPL_BUILD
 /*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
-#define CONFIG_SPL_WATCHDOG_SUPPORT
-#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
-#define CONFIG_SPL_POWER_SUPPORT
-#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_WATCHDOG
+#define CONFIG_SPL_DRIVERS_MISC
+#define CONFIG_SPL_POWER
+#define CONFIG_SPL_I2C
 #define CONFIG_SPL_LDSCRIPT            "arch/arm/cpu/armv8/u-boot-spl.lds"
 #define CONFIG_SPL_STACK               0x187FF0
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 #define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_GPIO_SUPPORT
-#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_GPIO
+#define CONFIG_SPL_MMC
 #define CONFIG_SPL_BSS_START_ADDR      0x00180000
 #define CONFIG_SPL_BSS_MAX_SIZE                0x2000  /* 8 KB */
 #define CONFIG_SYS_SPL_MALLOC_START    0x42200000
@@ -39,17 +38,6 @@
 #define CONFIG_SPL_ABORT_ON_RAW_IMAGE
 
 #undef CONFIG_DM_MMC
-#undef CONFIG_DM_PMIC
-
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC_I2C1                /* enable I2C bus 1 */
-#define CONFIG_SYS_I2C_MXC_I2C2                /* enable I2C bus 2 */
-#define CONFIG_SYS_I2C_MXC_I2C3                /* enable I2C bus 3 */
-
-#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
-
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
 #endif
 
 #define CONFIG_REMAKE_ELF
@@ -122,9 +110,6 @@
        "else booti ${loadaddr} - ${fdt_addr}; fi"
 
 /* Link Definitions */
-#define CONFIG_LOADADDR                        0x40480000
-
-#define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
 
 #define CONFIG_SYS_INIT_RAM_ADDR       0x40000000
 #define CONFIG_SYS_INIT_RAM_SIZE       0x80000
@@ -133,13 +118,8 @@
 #define CONFIG_SYS_INIT_SP_ADDR                \
        (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_SYS_MMC_ENV_DEV         1       /* USDHC2 */
 #define CONFIG_MMCROOT                 "/dev/mmcblk1p2"        /* USDHC2 */
 
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN          ((CONFIG_ENV_SIZE + (2 * 1024)) * 1024)
-
 #define CONFIG_SYS_SDRAM_BASE          0x40000000
 #define PHYS_SDRAM                     0x40000000
 #define PHYS_SDRAM_SIZE                        0x80000000      /* 2 GiB DDR */
@@ -148,7 +128,6 @@
 #define CONFIG_SYS_MEMTEST_END         (CONFIG_SYS_MEMTEST_START + \
                                        (PHYS_SDRAM_SIZE >> 1))
 
-#define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE           UART1_BASE_ADDR
 
 /* Monitor Command Prompt */
@@ -167,15 +146,8 @@
 
 #define CONFIG_MXC_GPIO
 
-/* I2C Configs */
-#define CONFIG_SYS_I2C_SPEED           100000
-
 #define CONFIG_OF_SYSTEM_SETUP
 
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_DM_PMIC
-#endif
-
 #define CONFIG_SYS_BOOTM_LEN           SZ_128M
 
 #endif