#ifndef __CONFIG_H
#define __CONFIG_H
+
+/* new uImage format support */
+#define CONFIG_FIT 1
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */
+
/*-----------------------------------------------------------------------
* High Level Configuration Options
*----------------------------------------------------------------------*/
*----------------------------------------------------------------------*/
#define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */
#define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */
-#define CFG_INIT_RAM_END (8 << 10)
+#define CFG_INIT_RAM_END (4 << 10)
#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data*/
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
-#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
/*-----------------------------------------------------------------------
* FLASH related
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
+#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+
+#define CONFIG_ENV_OVERWRITE 1
/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
-#endif /* CFG_ENV_IS_IN_FLASH */
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+#endif /* CONFIG_ENV_IS_IN_FLASH */
+
+#define ENV_NAME_REVLEV "revision_level"
+#define ENV_NAME_SOLDER "solder_switch"
+#define ENV_NAME_DIP "dip"
/*-----------------------------------------------------------------------
* DDR SDRAM
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */
#undef CONFIG_DDR_ECC /* don't use ECC */
#define SPD_EEPROM_ADDRESS {0x50}
+#define CONFIG_PROG_SDRAM_TLB 1
/*-----------------------------------------------------------------------
* I2C
#define CFG_I2C_EEPROM_ADDR (0xa4>>1)
#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
#define CFG_EEPROM_PAGE_WRITE_BITS 3
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"hostname=pcs440ep\0" \
+ "use_eeprom_ethaddr=default\0" \
+ "cs_test=off\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"load=tftp 100000 /tftpboot/pcs440ep/u-boot.bin\0" \
"update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \
"cp.b 100000 FFFA0000 60000\0" \
- "upd=run load;run update\0" \
+ "upd=run load update\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_self"
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#endif
+/* check U-Boot image with SHA1 sum */
+#define CONFIG_SHA1_CHECK_UB_IMG 1
+#define CONFIG_SHA1_START CFG_MONITOR_BASE
+#define CONFIG_SHA1_LEN CFG_MONITOR_LEN
+
+/*-----------------------------------------------------------------------
+ * Definitions for status LED
+ */
+#define CONFIG_STATUS_LED 1 /* Status LED enabled */
+#define CONFIG_BOARD_SPECIFIC_LED 1
+
+#define STATUS_LED_BIT 0x08 /* DIAG1 is on GPIO_PPC_1 */
+#define STATUS_LED_PERIOD ((CFG_HZ / 2) / 5) /* blink at 5 Hz */
+#define STATUS_LED_STATE STATUS_LED_OFF
+#define STATUS_LED_BIT1 0x04 /* DIAG2 is on GPIO_PPC_2 */
+#define STATUS_LED_PERIOD1 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */
+#define STATUS_LED_STATE1 STATUS_LED_ON
+#define STATUS_LED_BIT2 0x02 /* DIAG3 is on GPIO_PPC_3 */
+#define STATUS_LED_PERIOD2 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */
+#define STATUS_LED_STATE2 STATUS_LED_OFF
+#define STATUS_LED_BIT3 0x01 /* DIAG4 is on GPIO_PPC_4 */
+#define STATUS_LED_PERIOD3 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */
+#define STATUS_LED_STATE3 STATUS_LED_OFF
+
+#define CONFIG_SHOW_BOOT_PROGRESS 1
+
#define CONFIG_BAUDRATE 115200
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_HW_WATCHDOG /* watchdog */
#endif
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_ASKENV | \
- CFG_CMD_DHCP | \
- CFG_CMD_DIAG | \
- CFG_CMD_EEPROM | \
- CFG_CMD_ELF | \
- CFG_CMD_I2C | \
- CFG_CMD_IRQ | \
- CFG_CMD_MII | \
- CFG_CMD_NET | \
- CFG_CMD_NFS | \
- CFG_CMD_PCI | \
- CFG_CMD_PING | \
- CFG_CMD_REGINFO | \
- CFG_CMD_SDRAM | \
- CFG_CMD_EXT2 | \
- CFG_CMD_FAT | \
- CFG_CMD_USB )
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_SUPPORT_VFAT
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_REISER
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_USB
+
+#define CONFIG_SUPPORT_VFAT
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/
/* Board-specific PCI */
-#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */
#define CFG_PCI_TARGET_INIT
#define CFG_PCI_MASTER_INIT
/*-----------------------------------------------------------------------
* PPC440 GPIO Configuration
*/
-#define CFG_440_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
+#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
{ \
/* GPIO Core 0 */ \
{GPIO0_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO0 EBC_ADDR(7) DMA_REQ(2) */ \
} \
}
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */
-#define CFG_CACHELINE_SIZE 32 /* ... */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
/*
* Internal Definitions
*
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff Supports IDE harddisk
+ *-----------------------------------------------------------------------
+ */
+
+#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
+
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CFG_IDE_MAXDEVICE 1 /* max. 2 drives per IDE bus */
+
+#define CONFIG_IDE_PREINIT 1
+#define CONFIG_IDE_RESET 1
+
+#define CFG_ATA_IDE0_OFFSET 0x0000
+
+#define CFG_ATA_BASE_ADDR CFG_CF1
+
+/* Offset for data I/O */
+#define CFG_ATA_DATA_OFFSET 0
+
+/* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET)
+
+/* Offset for alternate registers */
+#define CFG_ATA_ALT_OFFSET (0x0000)
+
#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff