*----------------------------------------------------------------------*/
#define CONFIG_PCS440EP 1 /* Board is PCS440EP */
#define CONFIG_440EP 1 /* Specific PPC440EP support */
+#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
+#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer (placed in SDRAM)
*----------------------------------------------------------------------*/
+#define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */
#define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */
#define CFG_INIT_RAM_END (8 << 10)
#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data*/
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
+#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+
+#define CONFIG_ENV_OVERWRITE 1
/* Address and size of Redundant Environment Sector */
#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
#endif /* CFG_ENV_IS_IN_FLASH */
+#define ENV_NAME_REVLEV "revision_level"
+#define ENV_NAME_SOLDER "solder_switch"
+#define ENV_NAME_DIP "dip"
+
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */
#undef CONFIG_DDR_ECC /* don't use ECC */
-#define SPD_EEPROM_ADDRESS {0x50, 0x51}
+#define SPD_EEPROM_ADDRESS {0x50}
+#define CONFIG_PROG_SDRAM_TLB 1
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_MULTI_EEPROMS
-#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
+#define CFG_I2C_EEPROM_ADDR (0xa4>>1)
#define CFG_I2C_EEPROM_ADDR_LEN 1
#define CFG_EEPROM_PAGE_WRITE_ENABLE
#define CFG_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"hostname=pcs440ep\0" \
+ "use_eeprom_ethaddr=default\0" \
+ "cs_test=off\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"bootm\0" \
"rootpath=/opt/eldk/ppc_4xx\0" \
"bootfile=/tftpboot/pcs440ep/uImage\0" \
- "kernel_addr=fff00000\0" \
- "ramdisk_addr=fff00000\0" \
+ "kernel_addr=FFF00000\0" \
+ "ramdisk_addr=FFF00000\0" \
"load=tftp 100000 /tftpboot/pcs440ep/u-boot.bin\0" \
- "update=protect off fff80000 ffffffff;era fff80000 ffffffff;" \
- "cp.b 100000 fff80000 80000;" \
- "setenv filesize;saveenv\0" \
+ "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \
+ "cp.b 100000 FFFA0000 60000\0" \
"upd=run load;run update\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_self"
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#endif
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo"
+
+/* check U-Boot image with SHA1 sum */
+#define CONFIG_SHA1_CHECK_UB_IMG 1
+#define CONFIG_SHA1_START CFG_MONITOR_BASE
+#define CONFIG_SHA1_LEN CFG_MONITOR_LEN
+
+/*-----------------------------------------------------------------------
+ * Definitions for status LED
+ */
+#define CONFIG_STATUS_LED 1 /* Status LED enabled */
+#define CONFIG_BOARD_SPECIFIC_LED 1
+
+#define STATUS_LED_BIT 0x08 /* LED 1 is on GPIO_PPC_1 */
+#define STATUS_LED_PERIOD ((CFG_HZ / 2) / 5) /* blink at 5 Hz */
+#define STATUS_LED_STATE STATUS_LED_OFF
+#define STATUS_LED_BIT1 0x04 /* LED 2 is on GPIO_PPC_2 */
+#define STATUS_LED_PERIOD1 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */
+#define STATUS_LED_STATE1 STATUS_LED_ON
+#define STATUS_LED_BIT2 0x02 /* LED 3 is on GPIO_PPC_3 */
+#define STATUS_LED_PERIOD2 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */
+#define STATUS_LED_STATE2 STATUS_LED_OFF
+#define STATUS_LED_BIT3 0x01 /* LED 4 is on GPIO_PPC_4 */
+#define STATUS_LED_PERIOD3 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */
+#define STATUS_LED_STATE3 STATUS_LED_OFF
+
+#define CONFIG_SHOW_BOOT_PROGRESS 1
+
#define CONFIG_BAUDRATE 115200
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_HW_WATCHDOG /* watchdog */
#endif
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_ASKENV | \
- CFG_CMD_DHCP | \
- CFG_CMD_DIAG | \
- CFG_CMD_ELF | \
- CFG_CMD_I2C | \
- CFG_CMD_IRQ | \
- CFG_CMD_MII | \
- CFG_CMD_NET | \
- CFG_CMD_NFS | \
- CFG_CMD_PCI | \
- CFG_CMD_PING | \
- CFG_CMD_REGINFO | \
- CFG_CMD_SDRAM | \
- CFG_CMD_EXT2 | \
- CFG_CMD_FAT | \
- CFG_CMD_USB )
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_USB
-#define CONFIG_SUPPORT_VFAT
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#define CONFIG_SUPPORT_VFAT
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/
/* Board-specific PCI */
-#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */
#define CFG_PCI_TARGET_INIT
#define CFG_PCI_MASTER_INIT
/*-----------------------------------------------------------------------
* PPC440 GPIO Configuration
*/
-#define CFG_440_GPIO_TABLE { /* GPIO Alternate1 Alternate2 Alternate3 */ \
+#define CFG_440_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
{ \
/* GPIO Core 0 */ \
-{ GPIO0_BASE, GPIO_OUT, GPIO_SEL }, /* GPIO0 EBC_ADDR(7) DMA_REQ(2) */ \
-{ GPIO0_BASE, GPIO_OUT, GPIO_SEL }, /* GPIO1 EBC_ADDR(6) DMA_ACK(2) */ \
-{ GPIO0_BASE, GPIO_OUT, GPIO_SEL }, /* GPIO2 EBC_ADDR(5) DMA_EOT/TC(2) */ \
-{ GPIO0_BASE, GPIO_OUT, GPIO_SEL }, /* GPIO3 EBC_ADDR(4) DMA_REQ(3) */ \
-{ GPIO0_BASE, GPIO_OUT, GPIO_SEL }, /* GPIO4 EBC_ADDR(3) DMA_ACK(3) */ \
-{ GPIO0_BASE, GPIO_OUT, GPIO_SEL }, /* GPIO5 EBC_ADDR(2) DMA_EOT/TC(3) */ \
-{ GPIO0_BASE, GPIO_OUT, GPIO_ALT1 }, /* GPIO6 EBC_CS_N(1) */ \
-{ GPIO0_BASE, GPIO_OUT, GPIO_ALT1 }, /* GPIO7 EBC_CS_N(2) */ \
-{ GPIO0_BASE, GPIO_OUT, GPIO_ALT1 }, /* GPIO8 EBC_CS_N(3) */ \
-{ GPIO0_BASE, GPIO_OUT, GPIO_ALT1 }, /* GPIO9 EBC_CS_N(4) */ \
-{ GPIO0_BASE, GPIO_OUT, GPIO_SEL }, /* GPIO10 EBC_CS_N(5) */ \
-{ GPIO0_BASE, GPIO_OUT, GPIO_SEL }, /* GPIO11 EBC_BUS_ERR */ \
-{ GPIO0_BASE, GPIO_IN, GPIO_ALT1 }, /* GPIO12 ZII_p0Rxd(0) */ \
-{ GPIO0_BASE, GPIO_IN, GPIO_ALT1 }, /* GPIO13 ZII_p0Rxd(1) */ \
-{ GPIO0_BASE, GPIO_IN, GPIO_ALT1 }, /* GPIO14 ZII_p0Rxd(2) */ \
-{ GPIO0_BASE, GPIO_IN, GPIO_ALT1 }, /* GPIO15 ZII_p0Rxd(3) */ \
-{ GPIO0_BASE, GPIO_OUT, GPIO_ALT1 }, /* GPIO16 ZII_p0Txd(0) */ \
-{ GPIO0_BASE, GPIO_OUT, GPIO_ALT1 }, /* GPIO17 ZII_p0Txd(1) */ \
-{ GPIO0_BASE, GPIO_OUT, GPIO_ALT1 }, /* GPIO18 ZII_p0Txd(2) */ \
-{ GPIO0_BASE, GPIO_OUT, GPIO_ALT1 }, /* GPIO19 ZII_p0Txd(3) */ \
-{ GPIO0_BASE, GPIO_IN, GPIO_ALT1 }, /* GPIO20 ZII_p0Rx_er */ \
-{ GPIO0_BASE, GPIO_IN, GPIO_ALT1 }, /* GPIO21 ZII_p0Rx_dv */ \
-{ GPIO0_BASE, GPIO_IN, GPIO_ALT1 }, /* GPIO22 ZII_p0RxCrs */ \
-{ GPIO0_BASE, GPIO_OUT, GPIO_ALT1 }, /* GPIO23 ZII_p0Tx_er */ \
-{ GPIO0_BASE, GPIO_OUT, GPIO_ALT1 }, /* GPIO24 ZII_p0Tx_en */ \
-{ GPIO0_BASE, GPIO_IN, GPIO_ALT1 }, /* GPIO25 ZII_p0Col */ \
-{ GPIO0_BASE, GPIO_IN, GPIO_SEL }, /* GPIO26 USB2D_RXVALID */ \
-{ GPIO0_BASE, GPIO_IN, GPIO_SEL }, /* GPIO27 EXT_EBC_REQ USB2D_RXERROR */ \
-{ GPIO0_BASE, GPIO_IN, GPIO_SEL }, /* GPIO28 USB2D_TXVALID */ \
-{ GPIO0_BASE, GPIO_IN, GPIO_SEL }, /* GPIO29 EBC_EXT_HDLA USB2D_PAD_SUSPNDM */ \
-{ GPIO0_BASE, GPIO_IN, GPIO_SEL }, /* GPIO30 EBC_EXT_ACK USB2D_XCVRSELECT*/ \
-{ GPIO0_BASE, GPIO_IN, GPIO_SEL }, /* GPIO31 EBC_EXR_BUSREQ USB2D_TERMSELECT*/ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO0 EBC_ADDR(7) DMA_REQ(2) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO1 EBC_ADDR(6) DMA_ACK(2) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO2 EBC_ADDR(5) DMA_EOT/TC(2) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO3 EBC_ADDR(4) DMA_REQ(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO4 EBC_ADDR(3) DMA_ACK(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO5 EBC_ADDR(2) DMA_EOT/TC(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO6 EBC_CS_N(1) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO7 EBC_CS_N(2) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO8 EBC_CS_N(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO9 EBC_CS_N(4) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO10 EBC_CS_N(5) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO11 EBC_BUS_ERR */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO12 ZII_p0Rxd(0) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO13 ZII_p0Rxd(1) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO14 ZII_p0Rxd(2) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO15 ZII_p0Rxd(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO16 ZII_p0Txd(0) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO17 ZII_p0Txd(1) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO18 ZII_p0Txd(2) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO19 ZII_p0Txd(3) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO20 ZII_p0Rx_er */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO21 ZII_p0Rx_dv */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO22 ZII_p0RxCrs */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO23 ZII_p0Tx_er */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO24 ZII_p0Tx_en */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO25 ZII_p0Col */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO26 USB2D_RXVALID */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO27 EXT_EBC_REQ USB2D_RXERROR */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO28 USB2D_TXVALID */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO29 EBC_EXT_HDLA USB2D_PAD_SUSPNDM */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO30 EBC_EXT_ACK USB2D_XCVRSELECT*/ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO31 EBC_EXR_BUSREQ USB2D_TERMSELECT*/ \
}, \
{ \
/* GPIO Core 1 */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_SEL }, /* GPIO32 USB2D_OPMODE0 */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_SEL }, /* GPIO33 USB2D_OPMODE1 */ \
-{ GPIO1_BASE, GPIO_OUT, GPIO_ALT3 }, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \
-{ GPIO1_BASE, GPIO_IN, GPIO_ALT3 }, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \
-{ GPIO1_BASE, GPIO_IN, GPIO_ALT1 }, /* GPIO36 UART0_8PIN_CTS_N UART3_SIN*/ \
-{ GPIO1_BASE, GPIO_OUT, GPIO_ALT1 }, /* GPIO37 UART0_RTS_N */ \
-{ GPIO1_BASE, GPIO_OUT, GPIO_ALT2 }, /* GPIO38 UART0_DTR_N UART1_SOUT */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_ALT2 }, /* GPIO39 UART0_RI_N UART1_SIN */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_ALT1 }, /* GPIO40 UIC_IRQ(0) */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_ALT1 }, /* GPIO41 UIC_IRQ(1) */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_ALT1 }, /* GPIO42 UIC_IRQ(2) */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_ALT1 }, /* GPIO43 UIC_IRQ(3) */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_ALT1 }, /* GPIO44 UIC_IRQ(4) DMA_ACK(1) */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_SEL }, /* GPIO45 UIC_IRQ(6) DMA_EOT/TC(1) */ \
-{ GPIO1_BASE, GPIO_BI, GPIO_SEL }, /* GPIO46 UIC_IRQ(7) DMA_REQ(0) */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_SEL }, /* GPIO47 UIC_IRQ(8) DMA_ACK(0) */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_SEL }, /* GPIO48 UIC_IRQ(9) DMA_EOT/TC(0) */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_SEL }, /* GPIO49 Unselect via TraceSelect Bit */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_SEL }, /* GPIO50 Unselect via TraceSelect Bit */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_SEL }, /* GPIO51 Unselect via TraceSelect Bit */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_SEL }, /* GPIO52 Unselect via TraceSelect Bit */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_SEL }, /* GPIO53 Unselect via TraceSelect Bit */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_SEL }, /* GPIO54 Unselect via TraceSelect Bit */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_SEL }, /* GPIO55 Unselect via TraceSelect Bit */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_SEL }, /* GPIO56 Unselect via TraceSelect Bit */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_SEL }, /* GPIO57 Unselect via TraceSelect Bit */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_SEL }, /* GPIO58 Unselect via TraceSelect Bit */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_SEL }, /* GPIO59 Unselect via TraceSelect Bit */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_SEL }, /* GPIO60 Unselect via TraceSelect Bit */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_SEL }, /* GPIO61 Unselect via TraceSelect Bit */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_SEL }, /* GPIO62 Unselect via TraceSelect Bit */ \
-{ GPIO1_BASE, GPIO_IN, GPIO_SEL }, /* GPIO63 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO32 USB2D_OPMODE0 */ \
+{GPIO1_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO33 USB2D_OPMODE1 */ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT3, GPIO_OUT_NO_CHG}, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \
+{GPIO1_BASE, GPIO_IN, GPIO_ALT3, GPIO_OUT_NO_CHG}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \
+{GPIO1_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO36 UART0_8PIN_CTS_N UART3_SIN*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO37 UART0_RTS_N */ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_NO_CHG}, /* GPIO38 UART0_DTR_N UART1_SOUT */ \
+{GPIO1_BASE, GPIO_IN, GPIO_ALT2, GPIO_OUT_NO_CHG}, /* GPIO39 UART0_RI_N UART1_SIN */ \
+{GPIO1_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO40 UIC_IRQ(0) */ \
+{GPIO1_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO41 UIC_IRQ(1) */ \
+{GPIO1_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO42 UIC_IRQ(2) */ \
+{GPIO1_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO43 UIC_IRQ(3) */ \
+{GPIO1_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG}, /* GPIO44 UIC_IRQ(4) DMA_ACK(1) */ \
+{GPIO1_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO45 UIC_IRQ(6) DMA_EOT/TC(1) */ \
+{GPIO1_BASE, GPIO_BI, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO46 UIC_IRQ(7) DMA_REQ(0) */ \
+{GPIO1_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO47 UIC_IRQ(8) DMA_ACK(0) */ \
+{GPIO1_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO48 UIC_IRQ(9) DMA_EOT/TC(0) */ \
+{GPIO1_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO49 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO50 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO51 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO52 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO53 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO54 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO55 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO56 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO57 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO58 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO59 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO60 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO61 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO62 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO63 Unselect via TraceSelect Bit */ \
} \
}
*/
#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */
#define CFG_CACHELINE_SIZE 32 /* ... */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff Supports IDE harddisk
+ *-----------------------------------------------------------------------
+ */
+
+#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
+
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CFG_IDE_MAXDEVICE 1 /* max. 2 drives per IDE bus */
+
+#define CONFIG_IDE_PREINIT 1
+#define CONFIG_IDE_RESET 1
+
+#define CFG_ATA_IDE0_OFFSET 0x0000
+
+#define CFG_ATA_BASE_ADDR CFG_CF1
+
+/* Offset for data I/O */
+#define CFG_ATA_DATA_OFFSET 0
+
+/* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET)
+
+/* Offset for alternate registers */
+#define CFG_ATA_ALT_OFFSET (0x0000)
+
+/* These addresses need to be shifted one place to the left
+ * ( bus per_addr 20 -30 is connectsd on CF bus A10-A0)
+ * These values are shifted
+ */
+#define CFG_ATA_PORT_ADDR(port) ((port) << 1)
+
#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff