Convert CONFIG_CMD_IRQ to Kconfig

[platform/kernel/u-boot.git] / include / configs / p1_twr.h

diff --git a/include/configs/p1_twr.h b/include/configs/p1_twr.h
index f672ffe..fd644f2 100644 (file)
--- a/include/configs/p1_twr.h
+++ b/include/configs/p1_twr.h
@@ -12,7 +12,6 @@
 
 #if defined(CONFIG_TWR_P1025)
 #define CONFIG_BOARDNAME "TWR-P1025"
-#define CONFIG_P1025
 #define CONFIG_PHY_ATHEROS
 #define CONFIG_QE
 #define CONFIG_SYS_LBC_LBCR    0x00080000      /* Conversion of LBC addr */
@@ -39,14 +38,8 @@
 #define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE    /* start of monitor */
 #endif
 
-/* High Level Configuration Options */
-#define CONFIG_BOOKE
-#define CONFIG_E500
-
 #define CONFIG_MP
 
-#define CONFIG_FSL_ELBC
-#define CONFIG_PCI
 #define CONFIG_PCIE1   /* PCIE controller 1 (slot 1) */
 #define CONFIG_PCIE2   /* PCIE controller 2 (slot 2) */
 #define CONFIG_FSL_PCI_INIT    /* Use common FSL init code */
@@ -54,7 +47,6 @@
 #define CONFIG_FSL_PCIE_RESET  /* need PCIe reset errata */
 #define CONFIG_SYS_PCI_64BIT   /* enable 64-bit PCI resources */
 
-#define CONFIG_FSL_LAW
 #define CONFIG_TSEC_ENET       /* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 
@@ -78,8 +70,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_L2_CACHE
 #define CONFIG_BTB
 
-#define CONFIG_BOARD_EARLY_INIT_F      /* Call board_pre_init */
-
 #define CONFIG_SYS_MEMTEST_START       0x00200000      /* memtest works on */
 #define CONFIG_SYS_MEMTEST_END         0x1fffffff
 #define CONFIG_PANIC_HANG      /* do not reset board on panic */
@@ -88,7 +78,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_SYS_FSL_DDR3
 
 #define CONFIG_SYS_SDRAM_SIZE_LAW      LAW_SIZE_512M
 #define CONFIG_CHIP_SELECTS_PER_CTRL   1
@@ -97,7 +86,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_DDR_SDRAM_BASE      0x00000000
 #define CONFIG_SYS_SDRAM_BASE          CONFIG_SYS_DDR_SDRAM_BASE
 
-#define CONFIG_NUM_DDR_CONTROLLERS     1
 #define CONFIG_DIMM_SLOTS_PER_CTLR     1
 
 /* Default settings for DDR3 */
@@ -242,7 +230,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_I2C_PCA9555_ADDR    0x23
 
 /* enable read and write access to EEPROM */
-#define CONFIG_CMD_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
@@ -280,11 +267,9 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_PCIE1_IO_PHYS       0xffc00000
 #define CONFIG_SYS_PCIE1_IO_SIZE       0x00010000      /* 64k */
 
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
 #define CONFIG_CMD_PCI
 
 #define CONFIG_PCI_SCAN_SHOW   /* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
 #endif /* CONFIG_PCI */
 
 #if defined(CONFIG_TSEC_ENET)
@@ -399,7 +384,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /*
  * Command line configuration.
  */
-#define CONFIG_CMD_IRQ
 #define CONFIG_CMD_REGINFO
 
 /*
@@ -408,25 +392,15 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_HAS_FSL_DR_USB
 
 #if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_USB_EHCI_FSL
 #endif
 #endif
 
-#define CONFIG_MMC
-
 #ifdef CONFIG_MMC
 #define CONFIG_FSL_ESDHC
 #define CONFIG_SYS_FSL_ESDHC_ADDR      CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_GENERIC_MMC
-#endif
-
-#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \
-                || defined(CONFIG_FSL_SATA)
-#define CONFIG_DOS_PARTITION
 #endif
 
 #undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -468,8 +442,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #define CONFIG_BOOTARGS        /* the boot command will set bootargs */
 
-#define CONFIG_BAUDRATE        115200
-
 #define        CONFIG_EXTRA_ENV_SETTINGS       \
 "netdev=eth0\0"        \
 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"    \