configs: Finish migration of PHY_GIGE

[platform/kernel/u-boot.git] / include / configs / p1_twr.h

diff --git a/include/configs/p1_twr.h b/include/configs/p1_twr.h
index 041e016..df0b608 100644 (file)
--- a/include/configs/p1_twr.h
+++ b/include/configs/p1_twr.h
@@ -40,7 +40,6 @@
 
 #define CONFIG_MP
 
-#define CONFIG_FSL_ELBC
 #define CONFIG_PCIE1   /* PCIE controller 1 (slot 1) */
 #define CONFIG_PCIE2   /* PCIE controller 2 (slot 2) */
 #define CONFIG_FSL_PCI_INIT    /* Use common FSL init code */
@@ -51,7 +50,6 @@
 #define CONFIG_TSEC_ENET       /* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 
-#define CONFIG_CMD_SATA
 #define CONFIG_SATA_SIL3114
 #define CONFIG_SYS_SATA_MAX_DEVICE     2
 #define CONFIG_LIBATA
@@ -231,7 +229,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_I2C_PCA9555_ADDR    0x23
 
 /* enable read and write access to EEPROM */
-#define CONFIG_CMD_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
@@ -272,7 +269,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_CMD_PCI
 
 #define CONFIG_PCI_SCAN_SHOW   /* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
 #endif /* CONFIG_PCI */
 
 #if defined(CONFIG_TSEC_ENET)
@@ -299,8 +295,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #define CONFIG_ETHPRIME        "eTSEC1"
 
-#define CONFIG_PHY_GIGE        1       /* Include GbE speed/duplex detection */
-
 #define CONFIG_HAS_ETH0
 #define CONFIG_HAS_ETH1
 #undef CONFIG_HAS_ETH2
@@ -354,7 +348,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  */
 #define CONFIG_MTD_DEVICE
 #define CONFIG_MTD_PARTITIONS
-#define CONFIG_CMD_MTDPARTS
 #define CONFIG_FLASH_CFI_MTD
 #define MTDIDS_DEFAULT "nor0=ec000000.nor"
 #define MTDPARTS_DEFAULT "mtdparts=ec000000.nor:256k(vsc7385-firmware)," \
@@ -366,16 +359,13 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  */
 #ifdef CONFIG_SYS_RAMBOOT
 #ifdef CONFIG_RAMBOOT_SDCARD
-#define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_ENV_SIZE                0x2000
 #define CONFIG_SYS_MMC_ENV_DEV 0
 #else
-#define CONFIG_ENV_IS_NOWHERE  /* Store ENV in memory only */
 #define CONFIG_ENV_ADDR                (CONFIG_SYS_MONITOR_BASE - 0x1000)
 #define CONFIG_ENV_SIZE                0x2000
 #endif
 #else
-#define CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_ADDR        (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE                0x2000
 #define CONFIG_ENV_SECT_SIZE   0x20000 /* 128K (one sector) */
@@ -387,7 +377,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /*
  * Command line configuration.
  */
-#define CONFIG_CMD_IRQ
 #define CONFIG_CMD_REGINFO
 
 /*
@@ -396,9 +385,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_HAS_FSL_DR_USB
 
 #if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_USB_EHCI_FSL
 #endif
@@ -407,12 +394,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #ifdef CONFIG_MMC
 #define CONFIG_FSL_ESDHC
 #define CONFIG_SYS_FSL_ESDHC_ADDR      CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_GENERIC_MMC
-#endif
-
-#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \
-                || defined(CONFIG_FSL_SATA)
-#define CONFIG_DOS_PARTITION
 #endif
 
 #undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -454,8 +435,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #define CONFIG_BOOTARGS        /* the boot command will set bootargs */
 
-#define CONFIG_BAUDRATE        115200
-
 #define        CONFIG_EXTRA_ENV_SETTINGS       \
 "netdev=eth0\0"        \
 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"    \