#endif
#ifdef CONFIG_SDCARD
-#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10)
#define CONFIG_SYS_MMC_U_BOOT_DST (0x11000000)
#define CONFIG_SYS_MMC_U_BOOT_START (0x11000000)
#define CONFIG_SYS_MMC_U_BOOT_OFFS (128 << 10)
-#define CONFIG_SYS_MPC85XX_NO_RESETVEC
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SPL_COMMON_INIT_DDR
-#endif
#elif defined(CONFIG_SPIFLASH)
-#define CONFIG_SPL_SPI_FLASH_MINIMAL
-#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x11000000)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x11000000)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (128 << 10)
-#define CONFIG_SYS_MPC85XX_NO_RESETVEC
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SPL_COMMON_INIT_DDR
-#endif
#elif defined(CONFIG_MTD_RAW_NAND)
#ifdef CONFIG_TPL_BUILD
-#define CONFIG_SPL_NAND_INIT
-#define CONFIG_SPL_COMMON_INIT_DDR
-#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#define CONFIG_SYS_NAND_U_BOOT_SIZE (832 << 10)
#define CONFIG_SYS_NAND_U_BOOT_DST (0x11000000)
#define CONFIG_SYS_NAND_U_BOOT_START (0x11000000)
#elif defined(CONFIG_SPL_BUILD)
-#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#define CONFIG_SYS_NAND_U_BOOT_SIZE (128 << 10)
#define CONFIG_SYS_NAND_U_BOOT_DST 0xf8f80000
#define CONFIG_SYS_NAND_U_BOOT_START 0xf8f80000
-#else
-#ifndef CONFIG_MPC85XX_HAVE_RESET_VECTOR
-#define CONFIG_SYS_MPC85XX_NO_RESETVEC
-#endif
#endif /* not CONFIG_TPL_BUILD */
-
-#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#endif
#ifndef CONFIG_RESET_VECTOR_ADDRESS
#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
#endif
-#define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */
-#define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */
-
-#define CONFIG_LBA48
-
#define CONFIG_HWCONFIG
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CONFIG_L2_CACHE
-#define CONFIG_ENABLE_36BIT_PHYS
-
#define CONFIG_SYS_CCSRBAR 0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_SYS_DDR_RAW_TIMING
-#define CONFIG_SYS_SPD_BUS_NUM 1
#define SPD_EEPROM_ADDRESS 0x52
#if defined(CONFIG_TARGET_P1020RDB_PD)
* 0xf8f8_0000 0xf8ff_ffff L2 SRAM Up to 512K cacheable
* (early boot only)
* 0xff80_0000 0xff80_7fff NAND flash 32K non-cacheable CS1/0
- * 0xff98_0000 0xff98_ffff PMC 64K non-cacheable CS2
* 0xffa0_0000 0xffaf_ffff CPLD 1M non-cacheable CS3
* 0xffb0_0000 0xffbf_ffff VSC7385 switch 1M non-cacheable CS2
* 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable
/* Size of used area in RAM */
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
#endif
/* CPLD config size: 1Mb */
-#define CONFIG_SYS_PMC_BASE 0xff980000
-#define CONFIG_SYS_PMC_BASE_PHYS CONFIG_SYS_PMC_BASE
-#define CONFIG_PMC_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \
- BR_PS_8 | BR_V)
-#define CONFIG_PMC_OR_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
- OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \
- OR_GPCM_EAD)
-
/* Vsc7385 switch */
#ifdef CONFIG_VSC7385_ENET
#define __VSCFW_ADDR "vscfw_addr=ef000000\0"
#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
-#define CONFIG_SPL_RELOC_TEXT_BASE 0xf8f81000
-#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 112 * 1024)
-#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 116 * 1024)
-#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 148 * 1024)
-#if defined(CONFIG_TARGET_P2020RDB)
-#define CONFIG_SPL_RELOC_MALLOC_SIZE (364 << 10)
-#else
-#define CONFIG_SPL_RELOC_MALLOC_SIZE (108 << 10)
-#endif
#elif defined(CONFIG_MTD_RAW_NAND)
#ifdef CONFIG_TPL_BUILD
#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
-#define CONFIG_SPL_RELOC_TEXT_BASE 0xf8f81000
-#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 192 * 1024)
-#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 208 * 1024)
-#define CONFIG_SPL_RELOC_MALLOC_SIZE (48 << 10)
-#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 176 * 1024)
#else
#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
-#define CONFIG_SPL_RELOC_TEXT_BASE (CONFIG_SYS_INIT_L2_END - 0x2000)
-#define CONFIG_SPL_RELOC_STACK ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF)
#endif /* CONFIG_TPL_BUILD */
#endif
#endif
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
#endif
-#define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */
-
/*
* I2C2 EEPROM
*/
/*
* Environment
*/
-#if defined(CONFIG_SDCARD)
-#define CONFIG_FSL_FIXED_MMC_LOCATION
-#elif defined(CONFIG_MTD_RAW_NAND)
-#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE)
+#if defined(CONFIG_MTD_RAW_NAND)
#ifdef CONFIG_TPL_BUILD
#define SPL_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (160 << 10))
#endif
/*
* USB
*/
-#define CONFIG_HAS_FSL_DR_USB
-
-#if defined(CONFIG_HAS_FSL_DR_USB)
-#ifdef CONFIG_USB_EHCI_HCD
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#endif
-#endif
-
-#if defined(CONFIG_TARGET_P1020RDB_PD)
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
-#endif
#ifdef CONFIG_MMC
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
-#ifdef __SW_BOOT_NOR
-#define __NOR_RST_CMD \
-norboot=i2c dev CONFIG_SYS_SPD_BUS_NUM; i2c mw CONFIG_SYS_I2C_PCA9557_ADDR 1 __SW_BOOT_NOR 1; \
-i2c mw CONFIG_SYS_I2C_PCA9557_ADDR 3 __SW_BOOT_MASK 1; reset
-#endif
-#ifdef __SW_BOOT_SPI
-#define __SPI_RST_CMD \
-spiboot=i2c dev CONFIG_SYS_SPD_BUS_NUM; i2c mw CONFIG_SYS_I2C_PCA9557_ADDR 1 __SW_BOOT_SPI 1; \
-i2c mw CONFIG_SYS_I2C_PCA9557_ADDR 3 __SW_BOOT_MASK 1; reset
-#endif
-#ifdef __SW_BOOT_SD
-#define __SD_RST_CMD \
-sdboot=i2c dev CONFIG_SYS_SPD_BUS_NUM; i2c mw CONFIG_SYS_I2C_PCA9557_ADDR 1 __SW_BOOT_SD 1; \
-i2c mw CONFIG_SYS_I2C_PCA9557_ADDR 3 __SW_BOOT_MASK 1; reset
-#endif
-#ifdef __SW_BOOT_NAND
-#define __NAND_RST_CMD \
-nandboot=i2c dev CONFIG_SYS_SPD_BUS_NUM; i2c mw CONFIG_SYS_I2C_PCA9557_ADDR 1 __SW_BOOT_NAND 1; \
-i2c mw CONFIG_SYS_I2C_PCA9557_ADDR 3 __SW_BOOT_MASK 1; reset
-#endif
-#ifdef __SW_BOOT_PCIE
-#define __PCIE_RST_CMD \
-pciboot=i2c dev CONFIG_SYS_SPD_BUS_NUM; i2c mw CONFIG_SYS_I2C_PCA9557_ADDR 1 __SW_BOOT_PCIE 1; \
-i2c mw CONFIG_SYS_I2C_PCA9557_ADDR 3 __SW_BOOT_MASK 1; reset
-#endif
+#include "p1_p2_bootsrc.h"
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"nandfdtaddr=80000\0" \
"ramdisk_size=120000\0" \
__VSCFW_ADDR \
-"map_lowernorbank=i2c dev "__stringify(CONFIG_SYS_SPD_BUS_NUM)"; i2c mw "__stringify(CONFIG_SYS_I2C_PCA9557_ADDR)" 1 "__stringify(__SW_NOR_BANK_LO)" 1; i2c mw "__stringify(CONFIG_SYS_I2C_PCA9557_ADDR)" 3 "__stringify(__SW_NOR_BANK_MASK)" 1\0" \
-"map_uppernorbank=i2c dev "__stringify(CONFIG_SYS_SPD_BUS_NUM)"; i2c mw "__stringify(CONFIG_SYS_I2C_PCA9557_ADDR)" 1 "__stringify(__SW_NOR_BANK_UP)" 1; i2c mw "__stringify(CONFIG_SYS_I2C_PCA9557_ADDR)" 3 "__stringify(__SW_NOR_BANK_MASK)" 1\0" \
-__stringify(__NOR_RST_CMD)"\0" \
-__stringify(__SPI_RST_CMD)"\0" \
-__stringify(__SD_RST_CMD)"\0" \
-__stringify(__NAND_RST_CMD)"\0" \
-__stringify(__PCIE_RST_CMD)"\0"
+MAP_NOR_LO_CMD(map_lowernorbank) \
+MAP_NOR_UP_CMD(map_uppernorbank) \
+RST_NOR_CMD(norboot) \
+RST_SPI_CMD(spiboot) \
+RST_SD_CMD(sdboot) \
+RST_NAND_CMD(nandboot) \
+RST_PCIE_CMD(pciboot) \
+""
#define CONFIG_USB_FAT_BOOT \
"setenv bootargs root=/dev/ram rw " \
projects / platform / kernel / u-boot.git / blobdiff