Convert CONFIG_CMD_REGINFO to Kconfig

[platform/kernel/u-boot.git] / include / configs / p1_p2_rdb_pc.h

diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h
index d995d04..3b3baef 100644 (file)
--- a/include/configs/p1_p2_rdb_pc.h
+++ b/include/configs/p1_p2_rdb_pc.h
@@ -72,7 +72,6 @@
  */
 #define CONFIG_MTD_DEVICE
 #define CONFIG_MTD_PARTITIONS
-#define CONFIG_CMD_MTDPARTS
 #define CONFIG_FLASH_CFI_MTD
 #define MTDIDS_DEFAULT "nor0=ec000000.nor"
 #define MTDPARTS_DEFAULT "mtdparts=ec000000.nor:128k(dtb),6016k(kernel)," \
@@ -98,7 +97,6 @@
  */
 #define CONFIG_MTD_DEVICE
 #define CONFIG_MTD_PARTITIONS
-#define CONFIG_CMD_MTDPARTS
 #define CONFIG_FLASH_CFI_MTD
 #ifdef CONFIG_PHYS_64BIT
 #define MTDIDS_DEFAULT "nor0=fef000000.nor"
@@ -157,7 +155,6 @@
  */
 #define CONFIG_MTD_DEVICE
 #define CONFIG_MTD_PARTITIONS
-#define CONFIG_CMD_MTDPARTS
 #define CONFIG_FLASH_CFI_MTD
 #ifdef CONFIG_PHYS_64BIT
 #define MTDIDS_DEFAULT "nor0=fef000000.nor"
@@ -270,7 +267,6 @@
 #define CONFIG_TSEC_ENET       /* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 
-#define CONFIG_CMD_SATA
 #define CONFIG_SATA_SIL
 #define CONFIG_SYS_SATA_MAX_DEVICE     2
 #define CONFIG_LIBATA
@@ -434,7 +430,6 @@
 
 #define CONFIG_SYS_NAND_BASE_LIST      { CONFIG_SYS_NAND_BASE }
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
-#define CONFIG_CMD_NAND
 #if defined(CONFIG_TARGET_P1020RDB_PD)
 #define CONFIG_SYS_NAND_BLOCK_SIZE     (128 * 1024)
 #else
@@ -631,7 +626,6 @@
 #define CONFIG_SYS_I2C_PCA9557_ADDR    0x18
 
 /* enable read and write access to EEPROM */
-#define CONFIG_CMD_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
@@ -692,8 +686,6 @@
 #endif
 #define CONFIG_SYS_PCIE1_IO_SIZE       0x00010000      /* 64k */
 
-#define CONFIG_CMD_PCI
-
 #define CONFIG_PCI_SCAN_SHOW   /* show pci devices on startup */
 #endif /* CONFIG_PCI */
 
@@ -720,8 +712,6 @@
 
 #define CONFIG_ETHPRIME        "eTSEC1"
 
-#define CONFIG_PHY_GIGE        1       /* Include GbE speed/duplex detection */
-
 #define CONFIG_HAS_ETH0
 #define CONFIG_HAS_ETH1
 #define CONFIG_HAS_ETH2
@@ -774,7 +764,6 @@
  * Environment
  */
 #ifdef CONFIG_SPIFLASH
-#define CONFIG_ENV_IS_IN_SPI_FLASH
 #define CONFIG_ENV_SPI_BUS     0
 #define CONFIG_ENV_SPI_CS      0
 #define CONFIG_ENV_SPI_MAX_HZ  10000000
@@ -783,7 +772,6 @@
 #define CONFIG_ENV_OFFSET      0x100000        /* 1MB */
 #define CONFIG_ENV_SECT_SIZE   0x10000
 #elif defined(CONFIG_SDCARD)
-#define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_FSL_FIXED_MMC_LOCATION
 #define CONFIG_ENV_SIZE                0x2000
 #define CONFIG_SYS_MMC_ENV_DEV 0
@@ -794,15 +782,12 @@
 #else
 #define CONFIG_ENV_SIZE                CONFIG_SYS_NAND_BLOCK_SIZE
 #endif
-#define CONFIG_ENV_IS_IN_NAND
 #define CONFIG_ENV_OFFSET      (1024 * 1024)
 #define CONFIG_ENV_RANGE       (3 * CONFIG_ENV_SIZE)
 #elif defined(CONFIG_SYS_RAMBOOT)
-#define CONFIG_ENV_IS_NOWHERE  /* Store ENV in memory only */
 #define CONFIG_ENV_ADDR                (CONFIG_SYS_MONITOR_BASE - 0x1000)
 #define CONFIG_ENV_SIZE                0x2000
 #else
-#define CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_ADDR        (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE                0x2000
 #define CONFIG_ENV_SECT_SIZE   0x20000 /* 128K (one sector) */
@@ -812,20 +797,12 @@
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   /* allow baudrate change */
 
 /*
- * Command line configuration.
- */
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_REGINFO
-
-/*
  * USB
  */
 #define CONFIG_HAS_FSL_DR_USB
 
 #if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_USB_EHCI_FSL
 #endif