/*
* SoC Configuration
*/
-#define CONFIG_MACH_OMAPL138_LCDK
-#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID)
-#define CONFIG_SYS_OSCIN_FREQ 24000000
-#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE
-#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID)
-#define CONFIG_SYS_HZ 1000
-#define CONFIG_SKIP_LOWLEVEL_INIT_ONLY
+#define CFG_SYS_OSCIN_FREQ 24000000
+#define CFG_SYS_TIMERBASE DAVINCI_TIMER0_BASE
+#define CFG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID)
/*
* Memory Info
*/
-#define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024) /* malloc() len */
#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
#define PHYS_SDRAM_1_SIZE (128 << 20) /* SDRAM size 128MB */
-#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
-
-#define CONFIG_SPL_BSS_START_ADDR DAVINCI_DDR_EMIF_DATA_BASE
-#define CONFIG_SPL_BSS_MAX_SIZE 0x1080000
+#define CFG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
/* memtest start addr */
/* memtest will be run on 16MB */
-#define CONFIG_SYS_DA850_SYSCFG_SUSPSRC ( \
+#define CFG_SYS_DA850_SYSCFG_SUSPSRC ( \
DAVINCI_SYSCFG_SUSPSRC_TIMER0 | \
DAVINCI_SYSCFG_SUSPSRC_SPI1 | \
DAVINCI_SYSCFG_SUSPSRC_UART2 | \
*/
/* Requires CONFIG_SYS_DA850_PLL0_POSTDIV=0, set in Kconfig */
-#define CONFIG_SYS_DA850_PLL0_PLLM 18
-#define CONFIG_SYS_DA850_PLL1_PLLM 21
+#define CFG_SYS_DA850_PLL0_PLLM 18
+#define CFG_SYS_DA850_PLL1_PLLM 21
/*
* DDR2 memory configuration
*/
-#define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \
+#define CFG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \
DV_DDR_PHY_EXT_STRBEN | \
(0x5 << DV_DDR_PHY_RD_LATENCY_SHIFT))
-#define CONFIG_SYS_DA850_DDR2_SDBCR ( \
+#define CFG_SYS_DA850_DDR2_SDBCR ( \
(1 << DV_DDR_SDCR_DDR2EN_SHIFT) | \
(1 << DV_DDR_SDCR_DDREN_SHIFT) | \
(1 << DV_DDR_SDCR_SDRAMEN_SHIFT) | \
(2 << DV_DDR_SDCR_PAGESIZE_SHIFT))
/* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */
-#define CONFIG_SYS_DA850_DDR2_SDBCR2 0
+#define CFG_SYS_DA850_DDR2_SDBCR2 0
-#define CONFIG_SYS_DA850_DDR2_SDTIMR ( \
+#define CFG_SYS_DA850_DDR2_SDTIMR ( \
(19 << DV_DDR_SDTMR1_RFC_SHIFT) | \
(1 << DV_DDR_SDTMR1_RP_SHIFT) | \
(1 << DV_DDR_SDTMR1_RCD_SHIFT) | \
(1 << DV_DDR_SDTMR1_RRD_SHIFT) | \
(1 << DV_DDR_SDTMR1_WTR_SHIFT))
-#define CONFIG_SYS_DA850_DDR2_SDTIMR2 ( \
+#define CFG_SYS_DA850_DDR2_SDTIMR2 ( \
(7 << DV_DDR_SDTMR2_RASMAX_SHIFT) | \
(2 << DV_DDR_SDTMR2_XP_SHIFT) | \
(0 << DV_DDR_SDTMR2_ODT_SHIFT) | \
(1 << DV_DDR_SDTMR2_RTP_SHIFT) | \
(2 << DV_DDR_SDTMR2_CKE_SHIFT))
-#define CONFIG_SYS_DA850_DDR2_SDRCR 0x00000492
-#define CONFIG_SYS_DA850_DDR2_PBBPR 0x30
+#define CFG_SYS_DA850_DDR2_SDRCR 0x00000492
+#define CFG_SYS_DA850_DDR2_PBBPR 0x30
/*
* Serial Driver info
*/
-#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID)
+#define CFG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID)
-#define CONFIG_SYS_SPI_BASE DAVINCI_SPI1_BASE
-#define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI1_CLKID)
+#define CFG_SYS_SPI_BASE DAVINCI_SPI1_BASE
+#define CFG_SYS_SPI_CLK clk_get(DAVINCI_SPI1_CLKID)
/*
* I2C Configuration
*/
-#define CONFIG_SYS_DAVINCI_I2C_SPEED 25000
-#define CONFIG_SYS_DAVINCI_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */
-#define CONFIG_SYS_I2C_EXPANDER_ADDR 0x20
+#define CFG_SYS_I2C_EXPANDER_ADDR 0x20
/*
* Flash & Environment
*/
#ifdef CONFIG_MTD_RAW_NAND
-#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
-#define CONFIG_SYS_NAND_PAGE_2K
-#define CONFIG_SYS_NAND_CS 3
-#define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
-#define CONFIG_SYS_NAND_MASK_CLE 0x10
-#define CONFIG_SYS_NAND_MASK_ALE 0x8
-#undef CONFIG_SYS_NAND_HW_ECC
-#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
-#define CONFIG_SYS_NAND_HW_ECC_OOBFIRST
-#define CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_PAGE_SIZE (2 << 10)
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10)
-#define CONFIG_SYS_NAND_U_BOOT_SIZE SZ_512K
-#define CONFIG_SYS_NAND_U_BOOT_DST 0xc1080000
-#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
-#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_DST - \
- CONFIG_SYS_NAND_U_BOOT_SIZE - \
- CONFIG_SYS_MALLOC_LEN - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_NAND_ECCPOS { \
+#define CFG_SYS_NAND_CS 3
+#define CFG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
+#define CFG_SYS_NAND_MASK_CLE 0x10
+#define CFG_SYS_NAND_MASK_ALE 0x8
+#define CFG_SYS_NAND_U_BOOT_SIZE SZ_512K
+#define CFG_SYS_NAND_U_BOOT_DST 0xc1080000
+#define CFG_SYS_NAND_U_BOOT_START CFG_SYS_NAND_U_BOOT_DST
+#define CFG_SYS_NAND_ECCPOS { \
6, 7, 8, 9, 10, 11, 12, 13, 14, 15, \
22, 23, 24, 25, 26, 27, 28, 29, 30, 31, \
38, 39, 40, 41, 42, 43, 44, 45, 46, 47, \
54, 55, 56, 57, 58, 59, 60, 61, 62, 63 }
-#define CONFIG_SYS_NAND_PAGE_COUNT 64
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
-#define CONFIG_SYS_NAND_ECCSIZE 512
-#define CONFIG_SYS_NAND_ECCBYTES 10
-#define CONFIG_SYS_NAND_OOBSIZE 64
-#define CONFIG_SPL_NAND_BASE
-#define CONFIG_SPL_NAND_LOAD
-#endif
-
-/*
- * Network & Ethernet Configuration
- */
-#ifdef CONFIG_DRIVER_TI_EMAC
-#undef CONFIG_DRIVER_TI_EMAC_USE_RMII
-#define CONFIG_BOOTP_DEFAULT
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_NET_RETRY_COUNT 10
+#define CFG_SYS_NAND_ECCSIZE 512
+#define CFG_SYS_NAND_ECCBYTES 10
#endif
/*
* U-Boot general configuration
*/
-#define CONFIG_BOOTFILE "zImage" /* Boot file name */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000)
-
-/*
- * USB Configs
- */
-#define CONFIG_USB_OHCI_NEW
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
/*
* Linux Information
*/
#define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100)
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_REVISION_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_BOOTCOMMAND \
- "run envboot; " \
- "run mmcboot; "
#define DEFAULT_LINUX_BOOT_ENV \
"loadaddr=0xc0700000\0" \
#include <environment/ti/mmc.h>
-#define CONFIG_EXTRA_ENV_SETTINGS \
+#define CFG_EXTRA_ENV_SETTINGS \
DEFAULT_LINUX_BOOT_ENV \
DEFAULT_MMC_TI_ARGS \
"bootpart=0:2\0" \
"boot_fit=0\0" \
"console=ttyS2,115200n8\0"
-#ifdef CONFIG_CMD_BDI
-#define CONFIG_CLOCKS
-#endif
-
/* SD/MMC */
/* defines for SPL */
-#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE - \
- CONFIG_SYS_MALLOC_LEN)
-#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN
-#define CONFIG_SPL_STACK 0x8001ff00
-#define CONFIG_SPL_MAX_FOOTPRINT 32768
-#define CONFIG_SPL_PAD_TO 32768
/* additions for new relocation code, must added to all boards */
-#define CONFIG_SYS_SDRAM_BASE 0xc0000000
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
- GENERATED_GBL_DATA_SIZE)
+#define CFG_SYS_SDRAM_BASE 0xc0000000
#include <asm/arch/hardware.h>