/*
* Board
*/
-#undef CONFIG_USE_SPIFLASH
-#undef CONFIG_SYS_USE_NOR
/*
* SoC Configuration
*/
-#define CONFIG_MACH_OMAPL138_LCDK
-#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID)
#define CONFIG_SYS_OSCIN_FREQ 24000000
#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE
#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID)
-#define CONFIG_SYS_HZ 1000
-#define CONFIG_SKIP_LOWLEVEL_INIT
/*
* Memory Info
*/
-#define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024) /* malloc() len */
#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
#define PHYS_SDRAM_1_SIZE (128 << 20) /* SDRAM size 128MB */
#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
#define CONFIG_SPL_BSS_MAX_SIZE 0x1080000
/* memtest start addr */
-#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1 + 0x2000000)
/* memtest will be run on 16MB */
-#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024)
#define CONFIG_SYS_DA850_SYSCFG_SUSPSRC ( \
DAVINCI_SYSCFG_SUSPSRC_TIMER0 | \
* Serial Driver info
*/
#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID)
-#if !defined(CONFIG_DM_SERIAL)
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size */
-#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE /* Base address of UART2 */
-#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID)
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-#endif
#define CONFIG_SYS_SPI_BASE DAVINCI_SPI1_BASE
#define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI1_CLKID)
-#ifdef CONFIG_USE_SPIFLASH
-#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8000
-#define CONFIG_SYS_SPI_U_BOOT_SIZE 0x30000
-#endif
-
/*
* I2C Configuration
*/
/*
* Flash & Environment
*/
-#ifdef CONFIG_NAND
-#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */
-#define CONFIG_ENV_SIZE (128 << 9)
-#define CONFIG_SYS_NAND_USE_FLASH_BBT
+#ifdef CONFIG_MTD_RAW_NAND
#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
#define CONFIG_SYS_NAND_PAGE_2K
#define CONFIG_SYS_NAND_CS 3
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define CONFIG_SYS_NAND_HW_ECC_OOBFIRST
#define CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_PAGE_SIZE (2 << 10)
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10)
#define CONFIG_SYS_NAND_U_BOOT_SIZE SZ_512K
#define CONFIG_SYS_NAND_U_BOOT_DST 0xc1080000
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
22, 23, 24, 25, 26, 27, 28, 29, 30, 31, \
38, 39, 40, 41, 42, 43, 44, 45, 46, 47, \
54, 55, 56, 57, 58, 59, 60, 61, 62, 63 }
-#define CONFIG_SYS_NAND_PAGE_COUNT 64
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 10
-#define CONFIG_SYS_NAND_OOBSIZE 64
-#define CONFIG_SPL_NAND_BASE
-#define CONFIG_SPL_NAND_DRIVERS
-#define CONFIG_SPL_NAND_ECC
-#define CONFIG_SPL_NAND_LOAD
-#endif
-
-#ifdef CONFIG_SYS_USE_NOR
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */
-#define CONFIG_SYS_FLASH_SECT_SZ (128 << 10) /* 128KB */
-#define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SECT_SZ * 3)
-#define CONFIG_ENV_SIZE (128 << 10)
-#define CONFIG_SYS_FLASH_BASE DAVINCI_ASYNC_EMIF_DATA_CE2_BASE
-#define PHYS_FLASH_SIZE (8 << 20) /* Flash size 8MB */
-#define CONFIG_SYS_MAX_FLASH_SECT ((PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)\
- + 3)
-#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ
-#endif
-
-#ifdef CONFIG_USE_SPIFLASH
-#define CONFIG_ENV_SIZE (64 << 10)
-#define CONFIG_ENV_OFFSET (256 << 10)
-#define CONFIG_ENV_SECT_SIZE (64 << 10)
-#endif
-
-/*
- * Network & Ethernet Configuration
- */
-#ifdef CONFIG_DRIVER_TI_EMAC
-#undef CONFIG_DRIVER_TI_EMAC_USE_RMII
-#define CONFIG_BOOTP_DEFAULT
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_NET_RETRY_COUNT 10
#endif
/*
* U-Boot general configuration
*/
-#define CONFIG_BOOTFILE "zImage" /* Boot file name */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000)
-#define CONFIG_MX_CYCLIC
/*
* USB Configs
* Linux Information
*/
#define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100)
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_REVISION_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_BOOTCOMMAND \
- "run envboot; " \
- "run mmcboot; "
#define DEFAULT_LINUX_BOOT_ENV \
"loadaddr=0xc0700000\0" \
#define CONFIG_CLOCKS
#endif
-#if !defined(CONFIG_NAND) && \
- !defined(CONFIG_SYS_USE_NOR) && \
- !defined(CONFIG_USE_SPIFLASH)
-#define CONFIG_ENV_SIZE (16 << 10)
-#endif
-
/* SD/MMC */
-#ifdef CONFIG_ENV_IS_IN_MMC
-#undef CONFIG_ENV_SIZE
-#undef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */
-#define CONFIG_ENV_OFFSET (51 << 9) /* Sector 51 */
-#endif
-
-#ifndef CONFIG_DIRECT_NOR_BOOT
/* defines for SPL */
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE - \
CONFIG_SYS_MALLOC_LEN)
#define CONFIG_SPL_STACK 0x8001ff00
#define CONFIG_SPL_MAX_FOOTPRINT 32768
#define CONFIG_SPL_PAD_TO 32768
-#endif
/* additions for new relocation code, must added to all boards */
#define CONFIG_SYS_SDRAM_BASE 0xc0000000