/*
* Size of malloc() pool
- * Total Size Environment - 256k
+ * Total Size Environment - 128k
* Malloc - add 256k
*/
-#define CONFIG_ENV_SIZE (256 << 10)
+#define CONFIG_ENV_SIZE (128 << 10)
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (256 << 10))
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
/* initial data */
#define CONFIG_CONS_INDEX 3
#define CONFIG_SYS_NS16550_COM3 UART3_BASE
-#define CONFIG_ENV_IS_NOWHERE
-#define CONFIG_ENV_OVERWRITE
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
115200}
-
/* I2C */
#define CONFIG_HARD_I2C 1
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_TWL6030_POWER 1
/* MMC */
+#define CONFIG_GENERIC_MMC 1
#define CONFIG_MMC 1
-#define CONFIG_OMAP3_MMC 1
+#define CONFIG_OMAP_HSMMC 1
#define CONFIG_SYS_MMC_SET_DEV 1
#define CONFIG_DOS_PARTITION 1
+/* MMC ENV related defines */
+#define CONFIG_ENV_IS_IN_MMC 1
+#define CONFIG_SYS_MMC_ENV_DEV 1 /* SLOT2: eMMC(1) */
+#define CONFIG_ENV_OFFSET 0xE0000
+
/* USB */
#define CONFIG_MUSB_UDC 1
#define CONFIG_USB_OMAP3 1
#define CONFIG_USB_DEVICE 1
#define CONFIG_USB_TTY 1
#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
-/* Change these to suit your needs */
-#define CONFIG_USBD_VENDORID 0x0451
-#define CONFIG_USBD_PRODUCTID 0x5678
-#define CONFIG_USBD_MANUFACTURER "Texas Instruments"
-#define CONFIG_USBD_PRODUCT_NAME "SDP4430"
/* Flash */
#define CONFIG_SYS_NO_FLASH 1
#define CONFIG_CMD_FAT /* FAT support */
#define CONFIG_CMD_I2C /* I2C serial bus support */
#define CONFIG_CMD_MMC /* MMC support */
+#define CONFIG_CMD_SAVEENV
/* Disabled commands */
#undef CONFIG_CMD_NET
#undef CONFIG_CMD_IMLS /* List all found images */
/*
- * Enabling relocation of u-boot by default
- * Relocation can be skipped if u-boot is copied to the TEXT_BASE
- */
-#undef CONFIG_SKIP_RELOCATE_UBOOT
-
-/*
* Environment setup
*/
#define CONFIG_BOOTDELAY 3
-/* allow overwriting serial config and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_EXTRA_ENV_SETTINGS \
"console=ttyS2,115200n8\0" \
"usbtty=cdc_acm\0" \
"vram=16M\0" \
- "mmcdev=1\0" \
+ "mmcdev=0\0" \
"mmcroot=/dev/mmcblk0p2 rw\0" \
"mmcrootfstype=ext3 rootwait\0" \
"mmcargs=setenv bootargs console=${console} " \
"bootm ${loadaddr}\0" \
#define CONFIG_BOOTCOMMAND \
- "if mmc init ${mmcdev}; then " \
+ "if mmc rescan ${mmcdev}; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
*/
#define CONFIG_NR_DRAM_BANKS 1
+#define CONFIG_SYS_SDRAM_BASE 0x80000000
+#define CONFIG_SYS_INIT_SP_ADDR (LOW_LEVEL_SRAM_STACK - CONFIG_SYS_GBL_DATA_SIZE)
+
#endif /* __CONFIG_H */