+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2011 Logic Product Development <www.logicpd.com>
* Peter Barada <peter.barada@logicpd.com>
*
* Configuration settings for the Logic OMAP35x/DM37x SOM LV/Torpedo
* reference boards.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
/* High Level Configuration Options */
-#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
-
#include <configs/ti_omap3_common.h>
-#ifdef CONFIG_SPL_BUILD
-/*
- * Disable MMC DM for SPL build and can be re-enabled after adding
- * DM support in SPL
- */
-#undef CONFIG_DM_MMC
-#undef OMAP_HSMMC_USE_GPIO
-
-/* select serial console configuration for SPL */
-#undef CONFIG_CONS_INDEX
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
-#endif
-
-
/*
* We are only ever GP parts and will utilize all of the "downloaded image"
* area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB) in
* order to allow for BCH8 to fit in.
*/
#undef CONFIG_SPL_TEXT_BASE
-#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x40200000
-#define CONFIG_MISC_INIT_R /* misc_init_r dumps the die id */
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
/* Board NAND Info. */
#ifdef CONFIG_NAND
-#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
- /* to access nand */
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
/* NAND devices */
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
#define CONFIG_SYS_NAND_MAX_ECCPOS 56
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
#endif
/* Environment information */
"fi; " \
"else run defaultboot; fi\0" \
"defaultboot=run mmcramboot\0" \
- "consoledevice=ttyO0\0" \
+ "consoledevice=ttyS0\0" \
"setconsole=setenv console ${consoledevice},${baudrate}n8\0" \
"dump_bootargs=echo 'Bootargs: '; echo $bootargs\0" \
"rotation=0\0" \
"ip=${ipaddr}:${tftpserver}:${gatewayip}:${netmask}::eth0:off\0" \
"nfsrootpath=/opt/nfs-exports/omap\0" \
"autoload=no\0" \
+ "fdtimage=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
"loadfdt=mmc rescan; " \
"load mmc ${mmcdev} ${fdtaddr} ${fdtimage}\0" \
"mmcbootcommon=echo Booting with DT from mmc${mmcdev} ...; " \
"run loadramdisk\0" \
"mmcramboot=setenv bootfile uImage; " \
"run mmcrambootcommon; " \
- "bootm ${loadaddr} ${rdaddr} ${fdtimage}\0" \
+ "bootm ${loadaddr} ${rdaddr} ${fdtaddr}\0" \
"mmcrambootz=setenv bootfile zImage; " \
"run mmcrambootcommon; " \
- "bootz ${loadaddr} ${rdaddr} ${fdtimage}\0" \
+ "bootz ${loadaddr} ${rdaddr} ${fdtaddr}\0" \
"tftpboot=echo 'Booting kernel/ramdisk rootfs from tftp...'; " \
"run ramargs; " \
"run common_bootargs; " \
/* **** PISMO SUPPORT *** */
#if defined(CONFIG_CMD_NAND)
-#define CONFIG_SYS_FLASH_BASE NAND_BASE
+#define CONFIG_SYS_FLASH_BASE 0x10000000
#endif
+#define CONFIG_SYS_MAX_FLASH_SECT 256
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+#define CONFIG_SYS_FLASH_SIZE 0x4000000
+
/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE