/* High Level Configuration Options */
-#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
-
#include <configs/ti_omap3_common.h>
-#ifdef CONFIG_SPL_BUILD
-/* select serial console configuration for SPL */
-#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
-#endif
-
-
/*
* We are only ever GP parts and will utilize all of the "downloaded image"
* area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB) in
* order to allow for BCH8 to fit in.
*/
-#undef CONFIG_SPL_TEXT_BASE
-#define CONFIG_SPL_TEXT_BASE 0x40200000
-#define CONFIG_MISC_INIT_R /* misc_init_r dumps the die id */
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
/* I2C */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C64 */
+#ifdef CONFIG_SPL_BUILD
+#undef CONFIG_USB_EHCI_OMAP
+#endif
+#ifdef CONFIG_USB_EHCI_OMAP
+#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 4
+#endif
+
/* Board NAND Info. */
#ifdef CONFIG_NAND
-#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
- /* to access nand */
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
/* NAND devices */
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
/* Environment information */
-#define CONFIG_PREBOOT \
- "setenv preboot;" \
- "saveenv;"
-
#define CONFIG_EXTRA_ENV_SETTINGS \
DEFAULT_LINUX_BOOT_ENV \
"mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
"mmcdev=0\0" \
- "mmcroot=/dev/mmcblk0p2 rw\0" \
+ "finduuid=part uuid mmc ${mmcdev}:2 uuid\0" \
"mmcrootfstype=ext4 rootwait\0" \
"nandroot=ubi0:rootfs rw ubi.mtd=fs noinitrd\0" \
"nandrootfstype=ubifs rootwait\0" \
"ramargs=setenv bootargs "\
"root=/dev/ram rw ramdisk_size=${ramdisksize}\0" \
"mmcargs=setenv bootargs "\
- "root=${mmcroot} rootfstype=${mmcrootfstype}\0" \
+ "root=PARTUUID=${uuid} " \
+ "rootfstype=${mmcrootfstype} rw\0" \
"nandargs=setenv bootargs "\
"root=${nandroot} " \
"rootfstype=${nandrootfstype}\0" \
"ip=${ipaddr}:${tftpserver}:${gatewayip}:${netmask}::eth0:off\0" \
"nfsrootpath=/opt/nfs-exports/omap\0" \
"autoload=no\0" \
+ "fdtimage=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
"loadfdt=mmc rescan; " \
"load mmc ${mmcdev} ${fdtaddr} ${fdtimage}\0" \
"mmcbootcommon=echo Booting with DT from mmc${mmcdev} ...; " \
+ "run finduuid; "\
"run mmcargs; " \
"run common_bootargs; " \
"run dump_bootargs; " \
/* **** PISMO SUPPORT *** */
#if defined(CONFIG_CMD_NAND)
-#define CONFIG_SYS_FLASH_BASE NAND_BASE
+#define CONFIG_SYS_FLASH_BASE 0x10000000
#endif
+#define CONFIG_SYS_MAX_FLASH_SECT 256
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+#define CONFIG_SYS_FLASH_SIZE 0x4000000
+
/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
-
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
-#define CONFIG_ENV_OFFSET 0x260000
#define CONFIG_ENV_ADDR 0x260000
/* Defines for SPL */