+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2011 Logic Product Development <www.logicpd.com>
* Peter Barada <peter.barada@logicpd.com>
*
* Configuration settings for the Logic OMAP35x/DM37x SOM LV/Torpedo
* reference boards.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
/* High Level Configuration Options */
-#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
-
#include <configs/ti_omap3_common.h>
-#ifdef CONFIG_SPL_BUILD
-/*
- * Disable MMC DM for SPL build and can be re-enabled after adding
- * DM support in SPL
- */
-#undef CONFIG_DM_MMC
-#undef OMAP_HSMMC_USE_GPIO
-
-/* select serial console configuration for SPL */
-#undef CONFIG_CONS_INDEX
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
-#endif
-
-
/*
* We are only ever GP parts and will utilize all of the "downloaded image"
* area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB) in
* order to allow for BCH8 to fit in.
*/
-#undef CONFIG_SPL_TEXT_BASE
-#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_TEXT_BASE 0x40200000
-#define CONFIG_MISC_INIT_R /* misc_init_r dumps the die id */
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
/* Hardware drivers */
-#define CONFIG_USB_OMAP3
-
/* I2C */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C64 */
-/* USB */
-#define CONFIG_USB_MUSB_OMAP2PLUS
-#define CONFIG_USB_MUSB_PIO_ONLY
-
-/* TWL4030 */
-#define CONFIG_TWL4030_USB
+#ifdef CONFIG_USB_EHCI_OMAP
+#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 4
+#endif
/* Board NAND Info. */
#ifdef CONFIG_NAND
-#define CONFIG_NAND_OMAP_GPMC
-
-#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
- /* to access nand */
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
/* NAND devices */
-#define CONFIG_SYS_NAND_BUSWIDTH_16BIT
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
#define CONFIG_SYS_NAND_MAX_ECCPOS 56
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
-#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
-#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:"\
- "512k(MLO),"\
- "1792k(u-boot),"\
- "128k(spl-os)," \
- "128k(u-boot-env),"\
- "6m(kernel),-(fs)"
#endif
/* Environment information */
+#define CONFIG_USE_PREBOOT
#define CONFIG_PREBOOT \
"setenv preboot;" \
- "nand unlock;" \
"saveenv;"
#define CONFIG_EXTRA_ENV_SETTINGS \
DEFAULT_LINUX_BOOT_ENV \
- "mtdids=" MTDIDS_DEFAULT "\0" \
- "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
+ "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
"mmcdev=0\0" \
- "mmcroot=/dev/mmcblk0p2 rw\0" \
+ "finduuid=part uuid mmc ${mmcdev}:2 uuid\0" \
"mmcrootfstype=ext4 rootwait\0" \
"nandroot=ubi0:rootfs rw ubi.mtd=fs noinitrd\0" \
"nandrootfstype=ubifs rootwait\0" \
"fi; " \
"else run defaultboot; fi\0" \
"defaultboot=run mmcramboot\0" \
- "consoledevice=ttyO0\0" \
+ "consoledevice=ttyS0\0" \
"setconsole=setenv console ${consoledevice},${baudrate}n8\0" \
"dump_bootargs=echo 'Bootargs: '; echo $bootargs\0" \
"rotation=0\0" \
"ramargs=setenv bootargs "\
"root=/dev/ram rw ramdisk_size=${ramdisksize}\0" \
"mmcargs=setenv bootargs "\
- "root=${mmcroot} rootfstype=${mmcrootfstype}\0" \
+ "root=PARTUUID=${uuid} " \
+ "rootfstype=${mmcrootfstype} rw\0" \
"nandargs=setenv bootargs "\
"root=${nandroot} " \
"rootfstype=${nandrootfstype}\0" \
"ip=${ipaddr}:${tftpserver}:${gatewayip}:${netmask}::eth0:off\0" \
"nfsrootpath=/opt/nfs-exports/omap\0" \
"autoload=no\0" \
+ "fdtimage=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
"loadfdt=mmc rescan; " \
"load mmc ${mmcdev} ${fdtaddr} ${fdtimage}\0" \
"mmcbootcommon=echo Booting with DT from mmc${mmcdev} ...; " \
+ "run finduuid; "\
"run mmcargs; " \
"run common_bootargs; " \
"run dump_bootargs; " \
"run loadramdisk\0" \
"mmcramboot=setenv bootfile uImage; " \
"run mmcrambootcommon; " \
- "bootm ${loadaddr} ${rdaddr} ${fdtimage}\0" \
+ "bootm ${loadaddr} ${rdaddr} ${fdtaddr}\0" \
"mmcrambootz=setenv bootfile zImage; " \
"run mmcrambootcommon; " \
- "bootz ${loadaddr} ${rdaddr} ${fdtimage}\0" \
+ "bootz ${loadaddr} ${rdaddr} ${fdtaddr}\0" \
"tftpboot=echo 'Booting kernel/ramdisk rootfs from tftp...'; " \
"run ramargs; " \
"run common_bootargs; " \
"tftpboot $loadaddr zImage;" \
"bootz $loadaddr\0" \
"nandbootcommon=echo 'Booting kernel from NAND...';" \
- "nand unlock;" \
"run nandargs;" \
"run common_bootargs;" \
"run dump_bootargs;" \
/* **** PISMO SUPPORT *** */
#if defined(CONFIG_CMD_NAND)
-#define CONFIG_SYS_FLASH_BASE NAND_BASE
+#define CONFIG_SYS_FLASH_BASE 0x10000000
#endif
+#define CONFIG_SYS_MAX_FLASH_SECT 256
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+#define CONFIG_SYS_FLASH_SIZE 0x4000000
+
/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
-
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
-#define CONFIG_ENV_OFFSET 0x260000
#define CONFIG_ENV_ADDR 0x260000
-/* SMSC922x Ethernet */
-#if defined(CONFIG_CMD_NET)
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_32_BIT
-#define CONFIG_SMC911X_BASE 0x08000000
-#endif /* (CONFIG_CMD_NET) */
-
/* Defines for SPL */
/* NAND: SPL falcon mode configs */
projects / platform / kernel / u-boot.git / blobdiff