Add CONFIG_USE_PREBOOT to boards that use CONFIG_PREBOOT

[platform/kernel/u-boot.git] / include / configs / omap3_logic.h

diff --git a/include/configs/omap3_logic.h b/include/configs/omap3_logic.h
index 3b65a85..8b1773e 100644 (file)
--- a/include/configs/omap3_logic.h
+++ b/include/configs/omap3_logic.h
@@ -12,8 +12,6 @@
 
 /* High Level Configuration Options */
 
-#define CONFIG_NR_DRAM_BANKS   2       /* CS1 may or may not be populated */
-
 #include <configs/ti_omap3_common.h>
 
 /*
@@ -21,10 +19,7 @@
  * area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB) in
  * order to allow for BCH8 to fit in.
  */
-#undef CONFIG_SPL_TEXT_BASE
-#define CONFIG_SPL_TEXT_BASE           0x40200000
 
-#define CONFIG_MISC_INIT_R             /* misc_init_r dumps the die id */
 #define CONFIG_CMDLINE_TAG             /* enable passing of ATAGs */
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_INITRD_TAG
@@ -35,10 +30,12 @@
 /* I2C */
 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x50    /* EEPROM AT24C64      */
 
+#ifdef CONFIG_USB_EHCI_OMAP
+#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO       4
+#endif
+
 /* Board NAND Info. */
 #ifdef CONFIG_NAND
-#define CONFIG_SYS_NAND_ADDR           NAND_BASE /* physical address */
-                                                 /* to access nand */
 #define CONFIG_SYS_MAX_NAND_DEVICE     1         /* Max number of */
                                                  /* NAND devices */
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
@@ -63,6 +60,7 @@
 
 /* Environment information */
 
+#define CONFIG_USE_PREBOOT
 #define CONFIG_PREBOOT \
        "setenv preboot;"                                               \
        "saveenv;"
@@ -72,7 +70,7 @@
        "mtdids=" CONFIG_MTDIDS_DEFAULT "\0"    \
        "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
        "mmcdev=0\0" \
-       "mmcroot=/dev/mmcblk0p2 rw\0" \
+       "finduuid=part uuid mmc ${mmcdev}:2 uuid\0" \
        "mmcrootfstype=ext4 rootwait\0" \
        "nandroot=ubi0:rootfs rw ubi.mtd=fs noinitrd\0" \
        "nandrootfstype=ubifs rootwait\0" \
@@ -111,7 +109,8 @@
        "ramargs=setenv bootargs "\
                "root=/dev/ram rw ramdisk_size=${ramdisksize}\0" \
        "mmcargs=setenv bootargs "\
-               "root=${mmcroot} rootfstype=${mmcrootfstype}\0" \
+               "root=PARTUUID=${uuid} " \
+               "rootfstype=${mmcrootfstype} rw\0" \
        "nandargs=setenv bootargs "\
                "root=${nandroot} " \
                "rootfstype=${nandrootfstype}\0" \
@@ -121,9 +120,11 @@
                "ip=${ipaddr}:${tftpserver}:${gatewayip}:${netmask}::eth0:off\0" \
        "nfsrootpath=/opt/nfs-exports/omap\0" \
        "autoload=no\0" \
+       "fdtimage=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
        "loadfdt=mmc rescan; " \
                "load mmc ${mmcdev} ${fdtaddr} ${fdtimage}\0" \
        "mmcbootcommon=echo Booting with DT from mmc${mmcdev} ...; " \
+               "run finduuid; "\
                "run mmcargs; " \
                "run common_bootargs; " \
                "run dump_bootargs; " \
@@ -187,16 +188,18 @@
 
 /* **** PISMO SUPPORT *** */
 #if defined(CONFIG_CMD_NAND)
-#define CONFIG_SYS_FLASH_BASE          NAND_BASE
+#define CONFIG_SYS_FLASH_BASE          0x10000000
 #endif
 
+#define CONFIG_SYS_MAX_FLASH_SECT      256
+#define CONFIG_SYS_MAX_FLASH_BANKS     1
+#define CONFIG_SYS_FLASH_CFI_WIDTH     FLASH_CFI_16BIT
+#define CONFIG_SYS_FLASH_SIZE          0x4000000
+
 /* Monitor at start of flash */
 #define CONFIG_SYS_MONITOR_BASE                CONFIG_SYS_FLASH_BASE
 
-#define CONFIG_ENV_SIZE                        (128 << 10)     /* 128 KiB */
-
 #define CONFIG_SYS_ENV_SECT_SIZE       (128 << 10)     /* 128 KiB */
-#define CONFIG_ENV_OFFSET              0x260000
 #define CONFIG_ENV_ADDR                        0x260000
 
 /* Defines for SPL */