#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/sizes.h>
/*
* High Level Configuration Options
#include <asm/arch/cpu.h> /* get chip and board defs */
#include <asm/arch/omap3.h>
+/*
+ * Display CPU and Board information
+ */
+#define CONFIG_DISPLAY_CPUINFO 1
+#define CONFIG_DISPLAY_BOARDINFO 1
+
/* Clock Defines */
#define V_OSCK 26000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK >> 1)
/*
* Size of malloc() pool
*/
-#define CONFIG_ENV_SIZE SZ_128K /* Total Size Environment */
+#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
/* Sector */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
/* initial data */
-
/*
* Hardware drivers
*/
#define CONFIG_OMAP3_MMC 1
#define CONFIG_DOS_PARTITION 1
+/* DDR - I use Micron DDR */
+#define CONFIG_OMAP3_MICRON_DDR 1
+
/* commands to include */
#include <config_cmd_default.h>
#undef CONFIG_CMD_IMLS /* List all found images */
#define CONFIG_SYS_NO_FLASH
+#define CONFIG_HARD_I2C 1
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_SLAVE 1
#define CONFIG_SYS_I2C_BUS 0
#define CONFIG_DRIVER_OMAP34XX_I2C 1
/*
+ * TWL4030
+ */
+#define CONFIG_TWL4030_POWER 1
+
+/*
* Board NAND Info.
*/
#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
/* NAND devices */
-#define SECTORSIZE 512
-
-#define NAND_ALLOW_ERASE_ALL
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN 0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-#define NAND_NO_RB 1
-#define CONFIG_SYS_NAND_WP
+#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
#define CONFIG_JFFS2_NAND
/* nand device jffs2 lives on */
/* Environment information */
#define CONFIG_BOOTDELAY 10
+#define CONFIG_BOOTFILE uImage
+
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x82000000\0" \
"console=ttyS2,115200n8\0" \
/* address */
/*
- * 2430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
- * 32KHz clk, or from external sig. This rate is divided by a local divisor.
+ * OMAP3 has 12 GP timers, they can be driven by the system clock
+ * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
+ * This rate is divided by a local divisor.
*/
#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2
-#define CONFIG_SYS_PTV 7 /* 2^(PTV+1) */
-#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PTV))
+#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
+#define CONFIG_SYS_HZ 1000
/*-----------------------------------------------------------------------
* Stack sizes
*
* The stack sizes are set up in start.S using the settings below
*/
-#define CONFIG_STACKSIZE SZ_128K /* regular stack */
+#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ SZ_4K /* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ SZ_4K /* FIQ stack */
+#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack 4 KiB */
+#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack 4 KiB */
#endif
/*-----------------------------------------------------------------------
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE SZ_32M /* at least 32 meg */
+#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
/* SDRAM Bank Allocation method */
#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors */
/* on one chip */
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
-#define CONFIG_SYS_MONITOR_LEN SZ_256K /* Reserve 2 sectors */
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
#define CONFIG_SYS_FLASH_BASE boot_flash_base
#define CONFIG_SYS_JFFS2_NUM_BANKS 1
#ifndef __ASSEMBLY__
-extern gpmc_csx_t *nand_cs_base;
-extern gpmc_t *gpmc_cfg_base;
+extern struct gpmc *gpmc_cfg;
extern unsigned int boot_flash_base;
extern volatile unsigned int boot_flash_env_addr;
extern unsigned int boot_flash_off;
extern unsigned int boot_flash_type;
#endif
-
-#define WRITE_NAND_COMMAND(d, adr)\
- writel(d, &nand_cs_base->nand_cmd)
-#define WRITE_NAND_ADDRESS(d, adr)\
- writel(d, &nand_cs_base->nand_adr)
-#define WRITE_NAND(d, adr) writew(d, &nand_cs_base->nand_dat)
-#define READ_NAND(adr) readl(&nand_cs_base->nand_dat)
-
-/* Other NAND Access APIs */
-#define NAND_WP_OFF() do {readl(&gpmc_cfg_base->config) |= GPMC_CONFIG_WP; } \
- while (0)
-#define NAND_WP_ON() do {readl(&gpmc_cfg_base->config) &= ~GPMC_CONFIG_WP; } \
- while (0)
-#define NAND_DISABLE_CE(nand)
-#define NAND_ENABLE_CE(nand)
-#define NAND_WAIT_READY(nand) udelay(10)
-
/*----------------------------------------------------------------------------
* SMSC9115 Ethernet from SMSC9118 family
*----------------------------------------------------------------------------
*/
#if defined(CONFIG_CMD_NET)
-#define CONFIG_DRIVER_SMC911X
-#define CONFIG_DRIVER_SMC911X_32_BIT
-#define CONFIG_DRIVER_SMC911X_BASE 0x2C000000
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC911X
+#define CONFIG_SMC911X_32_BIT
+#define CONFIG_SMC911X_BASE 0x2C000000
#endif /* (CONFIG_CMD_NET) */
projects / platform / kernel / u-boot.git / blobdiff