* ----------------------------------------------------------------------------
*/
-#define CONFIG_CMD_JFFS2
-
#define CONFIG_CMD_NAND
/* ----------------------------------------------------------------------------
*/
#define CONFIG_SYS_LONGHELP
-/* Display CPU and Board information */
-#define CONFIG_DISPLAY_BOARDINFO
-
/* Allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
* ----------------------------------------------------------------------------
*/
-/* MMC */
-#define CONFIG_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_OMAP_HSMMC
-
/* SPL */
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
/* Partition tables */
-#define CONFIG_EFI_PARTITION
-#define CONFIG_DOS_PARTITION
/* USB
*
/*
* High level configuration options
*/
-#define CONFIG_OMAP /* This is TI OMAP core */
-#define CONFIG_OMAP_GPIO
-#define CONFIG_OMAP_COMMON
-/* Common ARM Erratas */
-#define CONFIG_ARM_ERRATA_454179
-#define CONFIG_ARM_ERRATA_430973
-#define CONFIG_ARM_ERRATA_621766
#define CONFIG_SDRC /* The chip has SDRC controller */
-#define CONFIG_OMAP3_EVM /* This is a OMAP3 EVM */
-#define CONFIG_TWL4030_POWER /* with TWL4030 PMIC */
-
/*
* Clock related definitions
*/
#define CONFIG_CONS_INDEX 1
#define CONFIG_SERIAL1 1 /* UART1 on OMAP3 EVM */
#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
-#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
115200}
#ifdef CONFIG_USB_MUSB_HCD
-#define CONGIG_CMD_STORAGE
-
#ifdef CONFIG_USB_KEYBOARD
#define CONFIG_SYS_USB_EVENT_POLL
#define CONFIG_PREBOOT "usb start"
/* USB device configuration */
#define CONFIG_USB_DEVICE
#define CONFIG_USB_TTY
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
/* Change these to suit your needs */
#define CONFIG_USBD_VENDORID 0x0451
#if !defined(CONFIG_ENV_IS_NOWHERE)
#if defined(CONFIG_CMD_NAND)
-#define CONFIG_ENV_IS_IN_NAND
#elif defined(CONFIG_CMD_ONENAND)
-#define CONFIG_ENV_IS_IN_ONENAND
#define CONFIG_ENV_OFFSET ONENAND_ENV_OFFSET
#endif
#endif /* CONFIG_ENV_IS_NOWHERE */
* Board specific
* -----------------------------------------------------------------------------
*/
-#define CONFIG_SYS_NO_FLASH
/* Uncomment to define the board revision statically */
/* #define CONFIG_STATIC_BOARD_REV OMAP3EVM_BOARD_GEN_2 */
#define CONFIG_SPL_BSS_START_ADDR 0x80000000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
-#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SPL_OMAP3_ID_NAND
-#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
+#define CONFIG_SPL_LDSCRIPT "arch/arm/mach-omap2/u-boot-spl.lds"
/*
* 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM