cgtqmx6eval: Add USB support

[platform/kernel/u-boot.git] / include / configs / omap3_beagle.h

diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index 9ba031d..e574742 100644 (file)
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -95,8 +95,6 @@
 #define CONFIG_OMAP3_GPIO_6            /* GPIO160..191 is in GPIO bank 6 */
 
 /* commands to include */
-#include <config_cmd_default.h>
-
 #define CONFIG_CMD_ASKENV
 
 #define CONFIG_CMD_CACHE
@@ -109,7 +107,6 @@
 #define CONFIG_USB_STORAGE     /* USB storage support          */
 #define CONFIG_CMD_NAND                /* NAND support                 */
 #define CONFIG_CMD_LED         /* LED support                  */
-#define CONFIG_CMD_SETEXPR     /* Evaluate expressions         */
 #define CONFIG_CMD_GPIO     /* Enable gpio command */
 #define CONFIG_CMD_DHCP
 
@@ -207,6 +204,9 @@
                "rootfstype=${ramrootfstype}\0" \
        "loadramdisk=load mmc ${bootpart} ${rdaddr} ${bootdir}/${ramdisk}\0" \
        "loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
+       "loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \
+       "bootscript=echo Running bootscript from mmc${mmcdev} ...; " \
+               "source ${loadaddr}\0" \
        "loadfdt=run validatefdt; load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
        "mmcboot=echo Booting from mmc ...; " \
                "run mmcargs; " \
@@ -243,9 +243,13 @@
                        "echo Running uenvcmd ...;" \
                        "run uenvcmd;" \
                "fi;" \
-               "if run loadimage; then " \
-                       "run mmcboot;" \
-               "fi;" \
+               "if run loadbootscript; then " \
+                       "run bootscript; " \
+               "else " \
+                       "if run loadimage; then " \
+                               "run mmcboot;" \
+                       "fi;" \
+               "fi; " \
        "fi;" \
        "run nandboot;" \
        "setenv bootfile zImage;" \
@@ -266,13 +270,8 @@
  */
 
 /* **** PISMO SUPPORT *** */
-
-/* Configure the PISMO */
-#define PISMO1_NAND_SIZE               GPMC_SIZE_128M
-#define PISMO1_ONEN_SIZE               GPMC_SIZE_128M
-
 #if defined(CONFIG_CMD_NAND)
-#define CONFIG_SYS_FLASH_BASE          PISMO1_NAND_BASE
+#define CONFIG_SYS_FLASH_BASE          NAND_BASE
 #endif
 
 /* Monitor at start of flash */
@@ -309,5 +308,11 @@
 #define CONFIG_SYS_NAND_ECCBYTES       3
 #define CONFIG_NAND_OMAP_ECCSCHEME     OMAP_ECC_HAM1_CODE_HW
 #define CONFIG_SYS_NAND_U_BOOT_OFFS    0x80000
+/* NAND: SPL falcon mode configs */
+#ifdef CONFIG_SPL_OS_BOOT
+#define CONFIG_CMD_SPL_NAND_OFS                0x240000
+#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS        0x280000
+#define CONFIG_CMD_SPL_WRITE_SIZE      0x2000
+#endif
 
 #endif /* __CONFIG_H */