*
* Configuration settings for the TI OMAP3530 Beagle board.
*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
/*
* High Level Configuration Options
*/
-#define CONFIG_ARMV7 1 /* This is an ARM V7 CPU core */
#define CONFIG_OMAP 1 /* in a TI OMAP core */
#define CONFIG_OMAP34XX 1 /* which is a 34XX */
-#define CONFIG_OMAP3430 1 /* which is in a 3430 */
#define CONFIG_OMAP3_BEAGLE 1 /* working with BEAGLE */
+#define CONFIG_OMAP_GPIO
+#define CONFIG_OMAP_COMMON
#define CONFIG_SDRC /* The chip has SDRC controller */
#define V_OSCK 26000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK >> 1)
-#undef CONFIG_USE_IRQ /* no support for IRQs */
#define CONFIG_MISC_INIT_R
+#define CONFIG_OF_LIBFDT
+#define CONFIG_CMD_BOOTZ
+
#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS 1
#define CONFIG_INITRD_TAG 1
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
/* Sector */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
- /* initial data */
/*
* Hardware drivers
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
115200}
+#define CONFIG_GENERIC_MMC 1
#define CONFIG_MMC 1
-#define CONFIG_OMAP3_MMC 1
+#define CONFIG_OMAP_HSMMC 1
#define CONFIG_DOS_PARTITION 1
-/* DDR - I use Micron DDR */
-#define CONFIG_OMAP3_MICRON_DDR 1
+/* Status LED */
+#define CONFIG_STATUS_LED 1
+#define CONFIG_BOARD_SPECIFIC_LED 1
+#define STATUS_LED_BIT 0x01
+#define STATUS_LED_STATE STATUS_LED_ON
+#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
+#define STATUS_LED_BIT1 0x02
+#define STATUS_LED_STATE1 STATUS_LED_ON
+#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
+#define STATUS_LED_BOOT STATUS_LED_BIT
+#define STATUS_LED_GREEN STATUS_LED_BIT1
+
+/* Enable Multi Bus support for I2C */
+#define CONFIG_I2C_MULTI_BUS 1
+
+/* Probe all devices */
+#define CONFIG_SYS_I2C_NOPROBES {{0x0, 0x0}}
/* USB */
-#define CONFIG_MUSB_UDC 1
-#define CONFIG_USB_OMAP3 1
+#define CONFIG_MUSB_GADGET
+#define CONFIG_USB_MUSB_OMAP2PLUS
+#define CONFIG_MUSB_PIO_ONLY
+#define CONFIG_USB_GADGET_DUALSPEED
#define CONFIG_TWL4030_USB 1
+#define CONFIG_USB_ETHER
+#define CONFIG_USB_ETHER_RNDIS
+
+/* USB EHCI */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+
+#define CONFIG_USB_EHCI_OMAP
+#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 147
+
+#define CONFIG_USB_ULPI
+#define CONFIG_USB_ULPI_VIEWPORT_OMAP
+
+#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_SMSC95XX
+#define CONFIG_USB_ETHER_ASIX
-/* USB device configuration */
-#define CONFIG_USB_DEVICE 1
-#define CONFIG_USB_TTY 1
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
/* commands to include */
#include <config_cmd_default.h>
+#define CONFIG_CMD_ASKENV
+
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_EXT2 /* EXT2 Support */
#define CONFIG_CMD_FAT /* FAT support */
-#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
+#define CONFIG_CMD_FS_GENERIC /* Generic FS support */
#define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
#define MTDIDS_DEFAULT "nand0=nand"
#define CONFIG_CMD_I2C /* I2C serial bus support */
#define CONFIG_CMD_MMC /* MMC support */
+#define CONFIG_USB_STORAGE /* USB storage support */
#define CONFIG_CMD_NAND /* NAND support */
+#define CONFIG_CMD_LED /* LED support */
+#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
+#define CONFIG_CMD_NFS /* NFS support */
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_SETEXPR /* Evaluate expressions */
+#define CONFIG_CMD_GPIO /* Enable gpio command */
#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
#undef CONFIG_CMD_IMI /* iminfo */
#undef CONFIG_CMD_IMLS /* List all found images */
-#undef CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
-#undef CONFIG_CMD_NFS /* NFS support */
#define CONFIG_SYS_NO_FLASH
#define CONFIG_HARD_I2C 1
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_SLAVE 1
-#define CONFIG_SYS_I2C_BUS 0
-#define CONFIG_SYS_I2C_BUS_SELECT 1
+#define CONFIG_I2C_MULTI_BUS 1
#define CONFIG_DRIVER_OMAP34XX_I2C 1
+#define CONFIG_VIDEO_OMAP3 /* DSS Support */
/*
* TWL4030
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
-#define CONFIG_JFFS2_NAND
-/* nand device jffs2 lives on */
-#define CONFIG_JFFS2_DEV "nand0"
-/* start of jffs2 partition */
-#define CONFIG_JFFS2_PART_OFFSET 0x680000
-#define CONFIG_JFFS2_PART_SIZE 0xf980000 /* size of jffs2 */
- /* partition */
/* Environment information */
-#define CONFIG_BOOTDELAY 10
+#define CONFIG_BOOTDELAY 3
#define CONFIG_EXTRA_ENV_SETTINGS \
- "loadaddr=0x82000000\0" \
+ "loadaddr=0x80200000\0" \
+ "rdaddr=0x81000000\0" \
+ "fdt_high=0xffffffff\0" \
+ "fdtaddr=0x80f80000\0" \
"usbtty=cdc_acm\0" \
- "console=ttyS2,115200n8\0" \
- "mpurate=500\0" \
+ "bootfile=uImage\0" \
+ "ramdisk=ramdisk.gz\0" \
+ "bootdir=/boot\0" \
+ "bootpart=0:2\0" \
+ "console=ttyO2,115200n8\0" \
+ "mpurate=auto\0" \
+ "buddy=none\0" \
+ "optargs=\0" \
+ "camera=none\0" \
"vram=12M\0" \
- "dvimode=1024x768MR-16@60\0" \
+ "dvimode=640x480MR-16@60\0" \
"defaultdisplay=dvi\0" \
+ "mmcdev=0\0" \
"mmcroot=/dev/mmcblk0p2 rw\0" \
"mmcrootfstype=ext3 rootwait\0" \
- "nandroot=/dev/mtdblock4 rw\0" \
- "nandrootfstype=jffs2\0" \
+ "nandroot=ubi0:rootfs ubi.mtd=4\0" \
+ "nandrootfstype=ubifs\0" \
+ "ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=0x81000000,64M\0" \
+ "ramrootfstype=ext2\0" \
"mmcargs=setenv bootargs console=${console} " \
+ "${optargs} " \
"mpurate=${mpurate} " \
+ "buddy=${buddy} "\
+ "camera=${camera} "\
"vram=${vram} " \
"omapfb.mode=dvi:${dvimode} " \
- "omapfb.debug=y " \
"omapdss.def_disp=${defaultdisplay} " \
"root=${mmcroot} " \
"rootfstype=${mmcrootfstype}\0" \
"nandargs=setenv bootargs console=${console} " \
+ "${optargs} " \
"mpurate=${mpurate} " \
+ "buddy=${buddy} "\
+ "camera=${camera} "\
"vram=${vram} " \
"omapfb.mode=dvi:${dvimode} " \
- "omapfb.debug=y " \
"omapdss.def_disp=${defaultdisplay} " \
"root=${nandroot} " \
"rootfstype=${nandrootfstype}\0" \
- "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
- "bootscript=echo Running bootscript from mmc ...; " \
- "source ${loadaddr}\0" \
- "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+ "findfdt=" \
+ "if test $beaglerev = AxBx; then " \
+ "setenv fdtfile omap3-beagle.dtb; fi; " \
+ "if test $beaglerev = Cx; then " \
+ "setenv fdtfile omap3-beagle.dtb; fi; " \
+ "if test $beaglerev = xMAB; then " \
+ "setenv fdtfile omap3-beagle-xm.dtb; fi; " \
+ "if test $beaglerev = xMC; then " \
+ "setenv fdtfile omap3-beagle-xm.dtb; fi; " \
+ "if test $fdtfile = undefined; then " \
+ "echo WARNING: Could not determine device tree to use; fi; \0" \
+ "bootenv=uEnv.txt\0" \
+ "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
+ "importbootenv=echo Importing environment from mmc ...; " \
+ "env import -t $loadaddr $filesize\0" \
+ "ramargs=setenv bootargs console=${console} " \
+ "${optargs} " \
+ "mpurate=${mpurate} " \
+ "buddy=${buddy} "\
+ "vram=${vram} " \
+ "omapfb.mode=dvi:${dvimode} " \
+ "omapdss.def_disp=${defaultdisplay} " \
+ "root=${ramroot} " \
+ "rootfstype=${ramrootfstype}\0" \
+ "loadramdisk=load mmc ${bootpart} ${rdaddr} ${bootdir}/${ramdisk}\0" \
+ "loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
+ "loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"bootm ${loadaddr}\0" \
+ "mmcbootz=echo Booting with DT from mmc${mmcdev} ...; " \
+ "run mmcargs; " \
+ "bootz ${loadaddr} - ${fdtaddr}\0" \
"nandboot=echo Booting from nand ...; " \
"run nandargs; " \
"nand read ${loadaddr} 280000 400000; " \
"bootm ${loadaddr}\0" \
-
+ "ramboot=echo Booting from ramdisk ...; " \
+ "run ramargs; " \
+ "bootm ${loadaddr}\0" \
+ "userbutton=if gpio input 173; then run userbutton_xm; " \
+ "else run userbutton_nonxm; fi;\0" \
+ "userbutton_xm=gpio input 4;\0" \
+ "userbutton_nonxm=gpio input 7;\0"
+/* "run userbutton" will return 1 (false) if pressed and 0 (true) if not */
#define CONFIG_BOOTCOMMAND \
- "if mmc init; then " \
- "if run loadbootscript; then " \
- "run bootscript; " \
+ "run findfdt; " \
+ "mmc dev ${mmcdev}; if mmc rescan; then " \
+ "if run userbutton; then " \
+ "setenv bootenv uEnv.txt;" \
"else " \
- "if run loaduimage; then " \
- "run mmcboot; " \
- "else run nandboot; " \
- "fi; " \
- "fi; " \
- "else run nandboot; fi"
+ "setenv bootenv user.txt;" \
+ "fi;" \
+ "echo SD/MMC found on device ${mmcdev};" \
+ "if run loadbootenv; then " \
+ "echo Loaded environment from ${bootenv};" \
+ "run importbootenv;" \
+ "fi;" \
+ "if test -n $uenvcmd; then " \
+ "echo Running uenvcmd ...;" \
+ "run uenvcmd;" \
+ "fi;" \
+ "if run loadimage; then " \
+ "run mmcboot;" \
+ "fi;" \
+ "fi;" \
+ "run nandboot;" \
+ "setenv bootfile zImage;" \
+ "if run loadimage; then " \
+ "run loadfdt;" \
+ "run mmcbootz; " \
+ "fi; " \
#define CONFIG_AUTO_COMPLETE 1
/*
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_SYS_PROMPT "OMAP3 beagleboard.org # "
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
-#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) /* memtest */
- /* works on */
-#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
- 0x01F00000) /* 31MB */
+#define CONFIG_SYS_ALT_MEMTEST 1
+#define CONFIG_SYS_MEMTEST_START (0x82000000) /* memtest */
+ /* defaults */
+#define CONFIG_SYS_MEMTEST_END (0x87FFFFFF) /* 128MB */
+#define CONFIG_SYS_MEMTEST_SCRATCH (0x81000000) /* dummy address */
#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */
/* load address */
#define CONFIG_SYS_HZ 1000
/*-----------------------------------------------------------------------
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
-#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack 4 KiB */
-#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack 4 KiB */
-#endif
-
-/*-----------------------------------------------------------------------
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
-/* SDRAM Bank Allocation method */
-#define SDRC_R_B_C 1
-
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
-#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors on */
- /* one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
-#define CONFIG_SYS_FLASH_BASE boot_flash_base
+#if defined(CONFIG_CMD_NAND)
+#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE
+#endif
/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */
#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
-#define CONFIG_SYS_ENV_SECT_SIZE boot_flash_sec
-#define CONFIG_ENV_OFFSET boot_flash_off
+#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
+#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
-
-/* Flash banks JFFS2 should use */
-#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
- CONFIG_SYS_MAX_NAND_DEVICE)
-#define CONFIG_SYS_JFFS2_MEM_NAND
-/* use flash_info[2] */
-#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_NUM_BANKS 1
-
-#ifndef __ASSEMBLY__
-extern unsigned int boot_flash_base;
-extern volatile unsigned int boot_flash_env_addr;
-extern unsigned int boot_flash_off;
-extern unsigned int boot_flash_sec;
-extern unsigned int boot_flash_type;
-#endif
-
-/* additions for new relocation code, must be added to all boards */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_SP_ADDR (LOW_LEVEL_SRAM_STACK - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
+#define CONFIG_SYS_INIT_RAM_SIZE 0x800
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+
+#define CONFIG_OMAP3_SPI
+
+#define CONFIG_SYS_CACHELINE_SIZE 64
+
+/* Defines for SPL */
+#define CONFIG_SPL
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_NAND_SIMPLE
+#define CONFIG_SPL_TEXT_BASE 0x40200800
+#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */
+#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
+
+#define CONFIG_SPL_BSS_START_ADDR 0x80000000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
+
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
+#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
+#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
+
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SPL_GPIO_SUPPORT
+#define CONFIG_SPL_POWER_SUPPORT
+#define CONFIG_SPL_OMAP3_ID_NAND
+#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
+
+/* NAND boot config */
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_COUNT 64
+#define CONFIG_SYS_NAND_PAGE_SIZE 2048
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
+#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
+ 10, 11, 12, 13}
+#define CONFIG_SYS_NAND_ECCSIZE 512
+#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+
+/*
+ * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
+ * 64 bytes before this address should be set aside for u-boot.img's
+ * header. That is 0x800FFFC0--0x80100000 should not be used for any
+ * other needs.
+ */
+#define CONFIG_SYS_TEXT_BASE 0x80100000
+#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
#endif /* __CONFIG_H */