+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2006-2008
* Texas Instruments.
* Syed Mohammed Khasim <x0khasim@ti.com>
*
* Configuration settings for the TI OMAP3530 Beagle board.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
-
-/*
- * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
- * 64 bytes before this address should be set aside for u-boot.img's
- * header. That is 0x800FFFC0--0x80100000 should not be used for any
- * other needs. We use this rather than the inherited defines from
- * ti_armv7_common.h for backwards compatibility.
- */
-#define CONFIG_SYS_TEXT_BASE 0x80100000
-#define CONFIG_SPL_BSS_START_ADDR 0x80000000
-#define CONFIG_SPL_BSS_MAX_SIZE (512 << 10) /* 512 KB */
-#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
-#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
-
#include <configs/ti_omap3_common.h>
/*
- * Display CPU and Board information
+ * We are only ever GP parts and will utilize all of the "downloaded image"
+ * area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB).
*/
-#define CONFIG_DISPLAY_CPUINFO 1
-#define CONFIG_DISPLAY_BOARDINFO 1
-#define CONFIG_MISC_INIT_R
-
-#define CONFIG_REVISION_TAG 1
-#define CONFIG_ENV_OVERWRITE
-
-/* Status LED */
-#define CONFIG_STATUS_LED 1
-#define CONFIG_BOARD_SPECIFIC_LED 1
-#define STATUS_LED_BIT 0x01
-#define STATUS_LED_STATE STATUS_LED_ON
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BIT1 0x02
-#define STATUS_LED_STATE1 STATUS_LED_ON
-#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BOOT STATUS_LED_BIT
-#define STATUS_LED_GREEN STATUS_LED_BIT1
+/* NAND */
+#if defined(CONFIG_MTD_RAW_NAND)
+#define CONFIG_SYS_FLASH_BASE NAND_BASE
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
+ 10, 11, 12, 13}
+#define CONFIG_SYS_NAND_ECCSIZE 512
+#define CONFIG_SYS_NAND_ECCBYTES 3
+/* NAND: SPL falcon mode configs */
+#endif /* CONFIG_MTD_RAW_NAND */
/* Enable Multi Bus support for I2C */
-#define CONFIG_I2C_MULTI_BUS 1
-
-/* Probe all devices */
-#define CONFIG_SYS_I2C_NOPROBES {{0x0, 0x0}}
+#define CONFIG_I2C_MULTI_BUS
-/* USB */
-#define CONFIG_MUSB_GADGET
-#define CONFIG_USB_MUSB_OMAP2PLUS
-#define CONFIG_MUSB_PIO_ONLY
-#define CONFIG_USB_GADGET_DUALSPEED
-#define CONFIG_TWL4030_USB 1
-#define CONFIG_USB_ETHER
-#define CONFIG_USB_ETHER_RNDIS
-#define CONFIG_USB_GADGET
-#define CONFIG_USB_GADGET_VBUS_DRAW 0
-#define CONFIG_USBDOWNLOAD_GADGET
-#define CONFIG_G_DNL_VENDOR_NUM 0x0451
-#define CONFIG_G_DNL_PRODUCT_NUM 0xd022
-#define CONFIG_G_DNL_MANUFACTURER "TI"
-#define CONFIG_CMD_FASTBOOT
-#define CONFIG_ANDROID_BOOT_IMAGE
-#define CONFIG_USB_FASTBOOT_BUF_ADDR CONFIG_SYS_LOAD_ADDR
-#define CONFIG_USB_FASTBOOT_BUF_SIZE 0x07000000
+/* DSS Support */
-/* USB EHCI */
-#define CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
+/* TWL4030 LED Support */
-#define CONFIG_USB_EHCI_OMAP
-#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 147
+#define MEM_LAYOUT_ENV_SETTINGS \
+ DEFAULT_LINUX_BOOT_ENV
-#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
-#define CONFIG_USB_HOST_ETHER
-#define CONFIG_USB_ETHER_ASIX
-#define CONFIG_USB_ETHER_MCS7830
-#define CONFIG_USB_ETHER_SMSC95XX
+#define BOOTENV_DEV_LEGACY_MMC(devtypeu, devtypel, instance) \
+ "bootcmd_" #devtypel #instance "=" \
+ "setenv mmcdev " #instance "; " \
+ "run mmcboot\0"
+#define BOOTENV_DEV_NAME_LEGACY_MMC(devtypeu, devtypel, instance) \
+ #devtypel #instance " "
-/* GPIO banks */
-#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO bank 5 */
-#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */
+#if defined(CONFIG_MTD_RAW_NAND)
-/* commands to include */
-#include <config_cmd_default.h>
+#define BOOTENV_DEV_NAND(devtypeu, devtypel, instance) \
+ "bootcmd_" #devtypel #instance "=" \
+ "if test ${mtdids} = '' || test ${mtdparts} = '' ; then " \
+ "echo NAND boot disabled: No mtdids and/or mtdparts; " \
+ "else " \
+ "run nandboot; " \
+ "fi\0"
+#define BOOTENV_DEV_NAME_NAND(devtypeu, devtypel, instance) \
+ #devtypel #instance " "
-#define CONFIG_CMD_ASKENV
+#define BOOT_TARGET_DEVICES(func) \
+ func(MMC, mmc, 0) \
+ func(LEGACY_MMC, legacy_mmc, 0) \
+ func(UBIFS, ubifs, 0, rootfs, rootfs) \
+ func(NAND, nand, 0)
-#define CONFIG_CMD_CACHE
+#else /* !CONFIG_MTD_RAW_NAND */
-#define MTDIDS_DEFAULT "nand0=nand"
-#define MTDPARTS_DEFAULT "mtdparts=nand:512k(x-loader),"\
- "1920k(u-boot),128k(u-boot-env),"\
- "4m(kernel),-(fs)"
+#define BOOT_TARGET_DEVICES(func) \
+ func(MMC, mmc, 0) \
+ func(LEGACY_MMC, legacy_mmc, 0)
-#define CONFIG_USB_STORAGE /* USB storage support */
-#define CONFIG_CMD_NAND /* NAND support */
-#define CONFIG_CMD_LED /* LED support */
-#define CONFIG_CMD_GPIO /* Enable gpio command */
-#define CONFIG_CMD_DHCP
+#endif /* CONFIG_MTD_RAW_NAND */
-#define CONFIG_VIDEO_OMAP3 /* DSS Support */
-
-/*
- * TWL4030
- */
-#define CONFIG_TWL4030_LED 1
-
-/*
- * Board NAND Info.
- */
-#define CONFIG_SYS_NAND_QUIET_TEST 1
-#define CONFIG_NAND_OMAP_GPMC
-#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
- /* devices */
+#include <config_distro_bootcmd.h>
#define CONFIG_EXTRA_ENV_SETTINGS \
- "loadaddr=0x80200000\0" \
- "rdaddr=0x81000000\0" \
+ MEM_LAYOUT_ENV_SETTINGS \
+ "fdtfile=" CONFIG_DEFAULT_FDT_FILE "\0" \
"fdt_high=0xffffffff\0" \
- "fdtaddr=0x80f80000\0" \
- "usbtty=cdc_acm\0" \
- "bootfile=uImage\0" \
- "ramdisk=ramdisk.gz\0" \
+ "console=ttyO2,115200n8\0" \
"bootdir=/boot\0" \
+ "bootenv=uEnv.txt\0" \
+ "bootfile=zImage\0" \
"bootpart=0:2\0" \
- "console=ttyO2,115200n8\0" \
+ "usbtty=cdc_acm\0" \
"mpurate=auto\0" \
"buddy=none\0" \
- "optargs=\0" \
"camera=none\0" \
"vram=12M\0" \
"dvimode=640x480MR-16@60\0" \
"defaultdisplay=dvi\0" \
- "mmcdev=0\0" \
- "mmcroot=/dev/mmcblk0p2 rw\0" \
- "mmcrootfstype=ext3 rootwait\0" \
- "nandroot=ubi0:rootfs ubi.mtd=4\0" \
- "nandrootfstype=ubifs\0" \
- "ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=0x81000000,64M\0" \
- "ramrootfstype=ext2\0" \
- "mmcargs=setenv bootargs console=${console} " \
- "${optargs} " \
+ "defaultargs=setenv defargs " \
"mpurate=${mpurate} " \
"buddy=${buddy} "\
"camera=${camera} "\
"vram=${vram} " \
"omapfb.mode=dvi:${dvimode} " \
- "omapdss.def_disp=${defaultdisplay} " \
- "root=${mmcroot} " \
- "rootfstype=${mmcrootfstype}\0" \
- "nandargs=setenv bootargs console=${console} " \
- "${optargs} " \
- "mpurate=${mpurate} " \
- "buddy=${buddy} "\
- "camera=${camera} "\
- "vram=${vram} " \
- "omapfb.mode=dvi:${dvimode} " \
- "omapdss.def_disp=${defaultdisplay} " \
- "root=${nandroot} " \
- "rootfstype=${nandrootfstype}\0" \
+ "omapdss.def_disp=${defaultdisplay}\0" \
+ "optargs=\0" \
"findfdt=" \
"if test $beaglerev = AxBx; then " \
"setenv fdtfile omap3-beagle.dtb; fi; " \
"if test $beaglerev = xMC; then " \
"setenv fdtfile omap3-beagle-xm.dtb; fi; " \
"if test $fdtfile = undefined; then " \
- "echo WARNING: Could not determine device tree to use; fi; \0" \
+ "echo WARNING: Could not determine device tree to use; fi\0" \
+ "mmcdev=0\0" \
+ "mmcpart=2\0" \
+ "mmcroot=/dev/mmcblk0p2 rw\0" \
+ "mmcrootfstype=ext4 rootwait\0" \
+ "mmcargs=run defaultargs; setenv bootargs console=${console} " \
+ "${mtdparts} " \
+ "${defargs} " \
+ "${optargs} " \
+ "root=${mmcroot} " \
+ "rootfstype=${mmcrootfstype}\0" \
+ "userbutton_xm=gpio input 4;\0" \
+ "userbutton_nonxm=gpio input 7;\0" \
+ "userbutton=if gpio input 173; then " \
+ "run userbutton_xm; " \
+ "else " \
+ "run userbutton_nonxm; " \
+ "fi;\0" \
+ "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
+ "ext4bootenv=ext4load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootenv}\0" \
+ "importbootenv=echo Importing environment from mmc${mmcdev} ...; " \
+ "env import -t ${loadaddr} ${filesize}\0" \
+ "mmcbootenv=setenv bootpart ${mmcdev}:${mmcpart}; " \
+ "mmc dev ${mmcdev}; " \
+ "if mmc rescan; then " \
+ "if run userbutton; then " \
+ "setenv bootenv uEnv.txt;" \
+ "else " \
+ "setenv bootenv user.txt;" \
+ "fi;" \
+ "run loadbootenv && run importbootenv; " \
+ "run ext4bootenv && run importbootenv; " \
+ "if test -n $uenvcmd; then " \
+ "echo Running uenvcmd ...; " \
+ "run uenvcmd; " \
+ "fi; " \
+ "fi\0" \
"validatefdt=" \
"if test $beaglerev = xMAB; then " \
"if test ! -e mmc ${bootpart} ${bootdir}/${fdtfile}; then " \
"setenv fdtfile omap3-beagle-xm.dtb; " \
"fi; " \
"fi; \0" \
- "bootenv=uEnv.txt\0" \
- "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
- "importbootenv=echo Importing environment from mmc ...; " \
- "env import -t -r $loadaddr $filesize\0" \
- "ramargs=setenv bootargs console=${console} " \
+ "loadimage=ext4load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
+ "loaddtb=run validatefdt; ext4load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
+ "mmcboot=run mmcbootenv; " \
+ "if run loadimage && run loaddtb; then " \
+ "echo Booting ${bootdir}/${bootfile} from mmc ${bootpart} ...; " \
+ "run mmcargs; " \
+ "if test ${bootfile} = uImage; then " \
+ "bootm ${loadaddr} - ${fdtaddr}; " \
+ "fi; " \
+ "if test ${bootfile} = zImage; then " \
+ "bootz ${loadaddr} - ${fdtaddr}; " \
+ "fi; " \
+ "fi\0" \
+ "nandroot=ubi0:rootfs ubi.mtd=rootfs rw\0" \
+ "nandrootfstype=ubifs rootwait\0" \
+ "nandargs=run defaultargs; setenv bootargs console=${console} " \
+ "${mtdparts} " \
+ "${defargs} " \
"${optargs} " \
- "mpurate=${mpurate} " \
- "buddy=${buddy} "\
- "vram=${vram} " \
- "omapfb.mode=dvi:${dvimode} " \
- "omapdss.def_disp=${defaultdisplay} " \
- "root=${ramroot} " \
+ "root=${nandroot} " \
+ "rootfstype=${nandrootfstype}\0" \
+ "nandboot=if nand read ${loadaddr} kernel && nand read ${fdtaddr} dtb; then " \
+ "echo Booting uImage from NAND MTD 'kernel' partition ...; " \
+ "run nandargs; " \
+ "bootm ${loadaddr} - ${fdtaddr}; " \
+ "fi\0" \
+ "loadramdisk=ext4load mmc ${bootpart} ${rdaddr} ${bootdir}/${ramdisk}\0" \
+ "ramdisk=rootfs.ext2.gz.uboot\0" \
+ "ramdisk_size=16384\0" \
+ "ramroot=/dev/ram rw\0" \
+ "ramrootfstype=ext2\0" \
+ "ramargs=run defaultargs; setenv bootargs console=${console} " \
+ "${mtdparts} " \
+ "${defargs} " \
+ "${optargs} " \
+ "root=${ramroot} ramdisk_size=${ramdisk_size} " \
"rootfstype=${ramrootfstype}\0" \
- "loadramdisk=load mmc ${bootpart} ${rdaddr} ${bootdir}/${ramdisk}\0" \
- "loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
- "loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \
- "bootscript=echo Running bootscript from mmc${mmcdev} ...; " \
- "source ${loadaddr}\0" \
- "loadfdt=run validatefdt; load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
- "mmcboot=echo Booting from mmc ...; " \
- "run mmcargs; " \
- "bootm ${loadaddr}\0" \
- "mmcbootz=echo Booting with DT from mmc${mmcdev} ...; " \
- "run mmcargs; " \
- "bootz ${loadaddr} - ${fdtaddr}\0" \
- "nandboot=echo Booting from nand ...; " \
- "run nandargs; " \
- "nand read ${loadaddr} 280000 400000; " \
- "bootm ${loadaddr}\0" \
- "ramboot=echo Booting from ramdisk ...; " \
- "run ramargs; " \
- "bootm ${loadaddr}\0" \
- "userbutton=if gpio input 173; then run userbutton_xm; " \
- "else run userbutton_nonxm; fi;\0" \
- "userbutton_xm=gpio input 4;\0" \
- "userbutton_nonxm=gpio input 7;\0"
-/* "run userbutton" will return 1 (false) if pressed and 0 (true) if not */
-#define CONFIG_BOOTCOMMAND \
- "run findfdt; " \
- "mmc dev ${mmcdev}; if mmc rescan; then " \
- "if run userbutton; then " \
- "setenv bootenv uEnv.txt;" \
- "else " \
- "setenv bootenv user.txt;" \
- "fi;" \
- "echo SD/MMC found on device ${mmcdev};" \
- "if run loadbootenv; then " \
- "echo Loaded environment from ${bootenv};" \
- "run importbootenv;" \
- "fi;" \
- "if test -n $uenvcmd; then " \
- "echo Running uenvcmd ...;" \
- "run uenvcmd;" \
- "fi;" \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "else " \
- "if run loadimage; then " \
- "run mmcboot;" \
- "fi;" \
- "fi; " \
- "fi;" \
- "run nandboot;" \
- "setenv bootfile zImage;" \
- "if run loadimage; then " \
- "run loadfdt;" \
- "run mmcbootz; " \
- "fi; " \
-
-/*
- * OMAP3 has 12 GP timers, they can be driven by the system clock
- * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
- * This rate is divided by a local divisor.
- */
-#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-
-/* **** PISMO SUPPORT *** */
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_SYS_FLASH_BASE NAND_BASE
-#endif
-
-/* Monitor at start of flash */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP
-
-#define CONFIG_ENV_IS_IN_NAND 1
-#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
-#define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */
-#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
-
-#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
-#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
-#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
-
-#define CONFIG_OMAP3_SPI
-
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
-/* Defines for SPL */
-#define CONFIG_SPL_OMAP3_ID_NAND
-
-/* NAND boot config */
-#define CONFIG_SYS_NAND_BUSWIDTH_16BIT 16
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_PAGE_COUNT 64
-#define CONFIG_SYS_NAND_PAGE_SIZE 2048
-#define CONFIG_SYS_NAND_OOBSIZE 64
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
-#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
- 10, 11, 12, 13}
-#define CONFIG_SYS_NAND_ECCSIZE 512
-#define CONFIG_SYS_NAND_ECCBYTES 3
-#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
-/* NAND: SPL falcon mode configs */
-#ifdef CONFIG_SPL_OS_BOOT
-#define CONFIG_CMD_SPL_NAND_OFS 0x240000
-#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
-#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
-#endif
+ "ramboot=run mmcbootenv; " \
+ "if run loadimage && run loaddtb && run loadramdisk; then " \
+ "echo Booting ${bootdir}/${bootfile} from mmc ${bootpart} w/ramdisk ...; " \
+ "run ramargs; " \
+ "bootz ${loadaddr} ${rdaddr} ${fdtaddr}; " \
+ "fi\0" \
+ BOOTENV
#endif /* __CONFIG_H */