#define __CONFIG_H
/*
- * If we are developing, we might want to start armboot from ram
- * so we MUST NOT initialize critical regs like mem-timing ...
- */
-#define CONFIG_INIT_CRITICAL /* undef for developing */
-
-/*
* High Level Configuration Options
* (easy to change)
*/
/*
* Size of malloc() pool
*/
-#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024)
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
/*
* Hardware drivers
*/
-#define CONFIG_DRIVER_LAN91C96
+#define CONFIG_NET_MULTI
+#define CONFIG_LAN91C96
#define CONFIG_LAN91C96_BASE 0x04000300
#define CONFIG_LAN91C96_EXT_PHY
/*
* NS16550 Configuration
*/
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE (-4)
-#define CFG_NS16550_CLK (48000000) /* can be 12M/32Khz or 48Mhz */
-#define CFG_NS16550_COM1 0xfffb0000 /* uart1, bluetooth uart */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK (48000000) /* can be 12M/32Khz or 48Mhz */
+#define CONFIG_SYS_NS16550_COM1 0xfffb0000 /* uart1, bluetooth uart */
/*
* select serial console configuration
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_DHCP)
-#define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
#include <configs/omap1510.h>
#define CONFIG_BOOTDELAY 3
#define CONFIG_BOOTARGS "console=ttyS0,115200n8 noinitrd root=/dev/nfs ip=dhcp"
#define CONFIG_BOOTCOMMAND "bootp;tftp;bootm"
-#define CFG_AUTOLOAD "n" /* No autoload */
+#define CONFIG_SYS_AUTOLOAD "n" /* No autoload */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */
#endif
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "OMAP1610 H2 # " /* Monitor Command Prompt */
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "OMAP1610 H2 # " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
/* Print Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x10000000 /* memtest works on */
-#define CFG_MEMTEST_END 0x12000000 /* 32 MB in DRAM */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#define CONFIG_SYS_MEMTEST_START 0x10000000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x12000000 /* 32 MB in DRAM */
-#define CFG_LOAD_ADDR 0x10000000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x10000000 /* default load address */
/* The 1610 has 6 timers, they can be driven by the RefClk (12Mhz) or by
* DPLL1. This time is further subdivided by a local divisor.
*/
-#define CFG_TIMERBASE 0xFFFEC500 /* use timer 1 */
-#define CFG_PVT 7 /* 2^(pvt+1), divide by 256 */
-#define CFG_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CFG_PVT))
+#define CONFIG_SYS_TIMERBASE 0xFFFEC500 /* use timer 1 */
+#define CONFIG_SYS_PTV 7 /* 2^(PTV+1), divide by 256 */
+#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV))
/*-----------------------------------------------------------------------
* Stack sizes
#ifndef __ASSEMBLY__
extern unsigned long omap_flash_base; /* set in flash__init */
#endif
-#define CFG_FLASH_BASE omap_flash_base
+#define CONFIG_SYS_FLASH_BASE omap_flash_base
#elif defined(CONFIG_CS0_BOOT)
-#define CFG_FLASH_BASE PHYS_FLASH_1_BM0
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1_BM0
#else
-#define CFG_FLASH_BASE PHYS_FLASH_1_BM1
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1_BM1
#endif
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define PHYS_FLASH_SIZE 0x02000000 /* 32MB */
-#define CFG_MAX_FLASH_SECT (259) /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_SECT (259) /* max number of sectors on one chip */
/* addr of environment */
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x020000)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x020000)
/* timeout values are in ticks */
-#define CFG_FLASH_ERASE_TOUT (20*CFG_HZ) /* Timeout for Flash Erase */
-#define CFG_FLASH_WRITE_TOUT (20*CFG_HZ) /* Timeout for Flash Write */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (20*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (20*CONFIG_SYS_HZ) /* Timeout for Flash Write */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_SIZE 0x20000 /* Total Size of Environment Sector */
-#define CFG_ENV_OFFSET 0x20000 /* environment starts here */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SIZE 0x20000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_OFFSET 0x20000 /* environment starts here */
#endif /* __CONFIG_H */