#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/*
* Serial console configuration
*/
#define CONFIG_PCI 1
#define CONFIG_PCI_PNP 1
-#define CONFIG_PCI_SCAN_SHOW 1
+/* #define CONFIG_PCI_SCAN_SHOW 1 */
+#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
#define CONFIG_PCI_MEM_BUS 0x40000000
#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
#define CFG_XLB_PIPELINING 1
#define CONFIG_NET_MULTI 1
-#define CONFIG_EEPRO100 1
+#define CONFIG_EEPRO100
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_NS8382X 1
-#define ADD_PCI_CMD CFG_CMD_PCI
-
/* Partitions */
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
/*
- * Supported commands
+ * Command line configuration.
*/
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_EEPROM | \
- CFG_CMD_FAT | \
- CFG_CMD_I2C | \
- CFG_CMD_NFS | \
- CFG_CMD_SNTP | \
- CFG_CMD_MII | \
- CFG_CMD_PING | \
- ADD_PCI_CMD )
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_PCI
+
#if (TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */
# define CFG_LOWBOOT 1
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath)\0" \
+ "nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
- ":$(hostname):$(netdev):off panic=1\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
"flash_nfs=run nfsargs addip;" \
- "bootm $(kernel_addr)\0" \
+ "bootm ${kernel_addr}\0" \
"flash_self=run ramargs addip;" \
- "bootm $(kernel_addr) $(ramdisk_addr)\0" \
- "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
"rootpath=/opt/eldk/ppc_82xx\0" \
"bootfile=/tftpboot/MPC5200/uImage\0" \
""
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
+
+#if defined(CFG_IPBCLK_EQUALS_XLBCLK)
+/*
+ * PCI Bus clocking configuration
+ *
+ * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
+ * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
+ * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
+ */
+#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
+#endif
#endif
+
/*
* I2C configuration
*/
#define CFG_I2C_SLAVE 0x7F
/*
- * EEPROM configuration
+ * EEPROM configuration:
+ *
+ * O2DNT board is equiped with Ramtron FRAM device FM24CL16
+ * 16 Kib Ferroelectric Nonvolatile serial RAM memory
+ * organized as 2048 x 8 bits and addressable as eight I2C devices
+ * 0x50 ... 0x57 each 256 bytes in size
+ *
*/
+#define CFG_I2C_FRAM
#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */
#define CFG_I2C_EEPROM_ADDR_LEN 1
#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 70
+/*
+ * There is no write delay with FRAM, write operations are performed at bus
+ * speed. Thus, no status polling or write delay is needed.
+ */
+/*#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 70*/
+
/*
* Flash configuration
/*
* GPIO configuration
*/
-//#define CFG_GPS_PORT_CONFIG 0x10002004
-#define CFG_GPS_PORT_CONFIG 0x00002004 //no CAN
+/*#define CFG_GPS_PORT_CONFIG 0x10002004 */
+#define CFG_GPS_PORT_CONFIG 0x00002006 /* no CAN */
/*
* Miscellaneous configurable options
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
/*
* Various low-level settings
*/
#define CFG_BOOTCS_START CFG_FLASH_BASE
#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#define CFG_BOOTCS_CFG 0x00047801
+
+#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2
+/*
+ * For 66 MHz PCI clock additional Wait State is needed for CS0 (flash).
+ */
+#define CFG_BOOTCS_CFG 0x00057801 /* for pci_clk = 66 MHz */
+#else
+#define CFG_BOOTCS_CFG 0x00047801 /* for pci_clk = 33 MHz */
+#endif
+
#define CFG_CS0_START CFG_FLASH_BASE
#define CFG_CS0_SIZE CFG_FLASH_SIZE
projects / platform / kernel / u-boot.git / blobdiff