#define CONFIG_MXC_UART_BASE UART1_IPS_BASE_ADDR
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_BOARD_LATE_INIT
-
-/* Uncomment to enable secure boot support */
-/* #define CONFIG_SECURE_BOOT */
-#define CONFIG_CSF_SIZE 0x4000
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (32 * SZ_1M)
/* Network */
-#define CONFIG_CMD_MII
#define CONFIG_FEC_MXC
#define CONFIG_MII
#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_ETHPRIME "FEC"
#define CONFIG_FEC_MXC_PHYADDR 0
-#define CONFIG_PHYLIB
#define CONFIG_PHY_BROADCOM
/* ENET1 */
#define IMX_FEC_BASE ENET_IPS_BASE_ADDR
/* MMC Config*/
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
-/* PMIC */
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
-#define CONFIG_POWER_PFUZE3000
-#define CONFIG_POWER_PFUZE3000_I2C_ADDR 0x08
-
#undef CONFIG_BOOTM_NETBSD
#undef CONFIG_BOOTM_PLAN9
#undef CONFIG_BOOTM_RTEMS
-#undef CONFIG_CMD_EXPORTENV
-#undef CONFIG_CMD_IMPORTENV
-
/* I2C configs */
-#define CONFIG_CMD_I2C
-#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
#ifdef CONFIG_IMX_BOOTAUX
/* Set to QSPI1 A flash at default */
#define CONFIG_SYS_AUXCORE_BOOTDATA 0x60000000
-#define CONFIG_CMD_SETEXPR
#define UPDATE_M4_ENV \
"m4image=m4_qspi.bin\0" \
"fi; " \
"else run netboot; fi"
-#define CONFIG_CMD_MEMTEST
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x20000000)
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_SYS_HZ 1000
-#define CONFIG_STACKSIZE SZ_128K
-
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-/* FLASH and environment organization */
-#define CONFIG_SYS_NO_FLASH
+/* environment organization */
#define CONFIG_ENV_SIZE SZ_8K
-#define CONFIG_ENV_IS_IN_MMC
/*
* If want to use nand, define CONFIG_NAND_MXS and rework board
* to support nand, since emmc has pin conflicts with nand
*/
#ifdef CONFIG_NAND_MXS
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NAND_TRIMFFS
-
/* NAND stuff */
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE 0x40000000
#define CONFIG_APBH_DMA_BURST8
#endif
-#define CONFIG_ENV_OFFSET (8 * SZ_64K)
+#define CONFIG_ENV_OFFSET (12 * SZ_64K)
#ifdef CONFIG_NAND_MXS
#define CONFIG_SYS_FSL_USDHC_NUM 1
#else
#define CONFIG_MMCROOT "/dev/mmcblk0p2" /* USDHC1 */
/* USB Configs */
-#define CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX7
-#define CONFIG_USB_STORAGE
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
-#define CONFIG_MXC_USB_FLAGS 0
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_IMX_THERMAL
-#define CONFIG_CI_UDC
#define CONFIG_USBD_HS
-#define CONFIG_USB_GADGET_DUALSPEED
-#define CONFIG_USB_GADGET
-#define CONFIG_CMD_USB_MASS_STORAGE
#define CONFIG_USB_FUNCTION_MASS_STORAGE
-#define CONFIG_USB_GADGET_DOWNLOAD
-#define CONFIG_USB_GADGET_VBUS_DRAW 2
-
-#define CONFIG_G_DNL_VENDOR_NUM 0x0525
-#define CONFIG_G_DNL_PRODUCT_NUM 0xa4a5
-#define CONFIG_G_DNL_MANUFACTURER "FSL"
-
-/* USB Device Firmware Update support */
-#define CONFIG_CMD_DFU
-#define CONFIG_USB_FUNCTION_DFU
-#define CONFIG_DFU_MMC
-#define CONFIG_DFU_RAM
-#define CONFIG_VIDEO
#ifdef CONFIG_VIDEO
-#define CONFIG_CFB_CONSOLE
#define CONFIG_VIDEO_MXS
#define CONFIG_VIDEO_LOGO
-#define CONFIG_VIDEO_SW_CURSOR
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
-#define CONFIG_CMD_BMP
#define CONFIG_BMP_16BPP
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_VIDEO_BMP_LOGO
#endif
#ifdef CONFIG_FSL_QSPI
-#define CONFIG_CMD_SF
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_MACRONIX
#define CONFIG_SPI_FLASH_BAR