#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/arch/mx31-regs.h>
+#include <asm/arch/imx-regs.h>
/* High Level Configuration Options */
#define CONFIG_ARM1136 1 /* This is an arm1136 CPU core */
#define CONFIG_MX31 1 /* in a mx31 */
#define CONFIG_MX31_HCLK_FREQ 26000000 /* RedBoot says 26MHz */
-#define CONFIG_MX31_CLK32 32000
+#define CONFIG_MX31_CLK32 32768
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_SYS_TEXT_BASE 0xA0000000
+
+#define CONFIG_MACH_TYPE MACH_TYPE_MX31ADS
+
/*
* Disabled for now due to build problems under Debian and a significant increase
* in the final file size: 144260 vs. 109536 Bytes.
/*
* Size of malloc() pool
*/
-#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128 * 1024)
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024)
/*
* Hardware drivers
*/
-#define CONFIG_MX31_UART 1
-#define CFG_MX31_UART1 1
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART1_BASE
+
+#define CONFIG_HARD_SPI 1
+#define CONFIG_MXC_SPI 1
+#define CONFIG_DEFAULT_SPI_BUS 1
+#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH)
+#define CONFIG_MXC_GPIO
+
+/* PMIC Controller */
+#define CONFIG_PMIC
+#define CONFIG_PMIC_SPI
+#define CONFIG_PMIC_FSL
+#define CONFIG_FSL_PMIC_BUS 1
+#define CONFIG_FSL_PMIC_CS 0
+#define CONFIG_FSL_PMIC_CLK 1000000
+#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH)
+#define CONFIG_FSL_PMIC_BITLEN 32
+#define CONFIG_RTC_MC13XXX
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
-#define CFG_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
/***********************************************************
* Command definition
#include <config_cmd_default.h>
-#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_SPI
+#define CONFIG_CMD_DATE
#define CONFIG_BOOTDELAY 3
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_IPADDR 192.168.23.168
-#define CONFIG_SERVERIP 192.168.23.2
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "bootargs_base=setenv bootargs console=ttymxc0,115200\0" \
- "bootargs_nfs=setenv bootargs $(bootargs) root=/dev/nfs ip=dhcp nfsroot=$(serverip):$(nfsrootfs),v3,tcp\0" \
- "bootcmd=run bootcmd_net\0" \
- "bootcmd_net=run bootargs_base bootargs_mtd bootargs_nfs; tftpboot 0x80000000 uImage-mx31; bootm\0" \
- "prg_uboot=tftpboot 0x80000000 u-boot-mx31ads.bin; protect off 0xa0000000 0xa001ffff; erase 0xa0000000 0xa001ffff; cp.b 0x80000000 0xa0000000 $(filesize)\0"
-
+#define CONFIG_LOADADDR 0x80800000 /* loadaddr env var */
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "uboot_addr=0xa0000000\0" \
+ "uboot=mx31ads/u-boot.bin\0" \
+ "kernel=mx31ads/uImage\0" \
+ "nfsroot=/opt/eldk/arm\0" \
+ "bootargs_base=setenv bootargs console=ttymxc0,115200\0" \
+ "bootargs_nfs=setenv bootargs ${bootargs} root=/dev/nfs " \
+ "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+ "bootcmd=run bootcmd_net\0" \
+ "bootcmd_net=run bootargs_base bootargs_nfs; " \
+ "tftpboot ${loadaddr} ${kernel}; bootm\0" \
+ "prg_uboot=tftpboot ${loadaddr} ${uboot}; " \
+ "protect off ${uboot_addr} 0xa003ffff; " \
+ "erase ${uboot_addr} 0xa003ffff; " \
+ "cp.b ${loadaddr} ${uboot_addr} ${filesize}; " \
+ "setenv filesize; saveenv\0"
+
+#define CONFIG_CS8900
+#define CONFIG_CS8900_BASE 0xb4020300
+#define CONFIG_CS8900_BUS16 1 /* follow the Linux driver */
-#define CONFIG_DRIVER_CS8900 1
-#define CS8900_BASE 0xb4020300
-#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */
+/*
+ * The MX31ADS board seems to have a hardware "peculiarity" confirmed under
+ * U-Boot, RedBoot and Linux: the ethernet Rx signal is reaching the CS8900A
+ * controller inverted. The controller is capable of detecting and correcting
+ * this, but it needs 4 network packets for that. Which means, at startup, you
+ * will not receive answers to the first 4 packest, unless there have been some
+ * broadcasts on the network, or your board is on a hub. Reducing the ARP
+ * timeout from default 5 seconds to 200ms we speed up the initial TFTP
+ * transfer, should the user wish one, significantly.
+ */
+#define CONFIG_ARP_TIMEOUT 200UL
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> "
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> "
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
/* Print Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0 /* memtest works on */
-#define CFG_MEMTEST_END 0x10000
+#define CONFIG_SYS_MEMTEST_START 0 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x10000
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-#define CFG_LOAD_ADDR CSD0_BASE /* default load address */
-
-#define CFG_HZ 32000
+#define CONFIG_SYS_HZ 1000
#define CONFIG_CMDLINE_EDITING 1
/*-----------------------------------------------------------------------
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */
-
-/*-----------------------------------------------------------------------
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 CSD0_BASE
#define PHYS_SDRAM_1_SIZE (128 * 1024 * 1024)
+#define CONFIG_BOARD_EARLY_INIT_F
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_GBL_DATA_OFFSET)
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
-#define CFG_FLASH_BASE CS0_BASE
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 262 /* max number of sectors on one chip */
-#define CFG_MONITOR_BASE CFG_FLASH_BASE /* Monitor at beginning of flash */
-#define CFG_MONITOR_LEN (128 * 1024) /* Reserve 128KiB */
-
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_SECT_SIZE (32 * 1024)
-#define CFG_ENV_SIZE CFG_ENV_SECT_SIZE
-/* S29WS256N NOR flash has 4 32KiB small sectors at the beginning and at the end.
- * The rest of 32MiB is in 128KiB big sectors. U-Boot occupies the low 4 sectors,
- * if we put environment next to it, we will have to occupy 128KiB for it.
- * Putting it at the top of flash we use only 32KiB. */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 32 * 1024 * 1024 - CFG_ENV_SIZE)
+#define CONFIG_SYS_FLASH_BASE CS0_BASE
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 262 /* max number of sectors on one chip */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* Monitor at beginning of flash */
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256KiB */
+
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SECT_SIZE (128 * 1024)
+#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
+
/*-----------------------------------------------------------------------
* CFI FLASH driver setup
*/
-#define CFG_FLASH_CFI 1 /* Flash memory is CFI compliant */
-#define CFG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */
-#if 0 /* Doesn't work yet, work in progress */
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */
-#endif
-#define CFG_FLASH_PROTECTION 1 /* Use hardware sector protection */
+#define CONFIG_SYS_FLASH_CFI 1 /* Flash memory is CFI compliant */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */
+#define CONFIG_FLASH_SPANSION_S29WS_N 1 /* A non-standard buffered write algorithm */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use hardware sector protection */
/*
* JFFS2 partitions
*/
-#undef CONFIG_JFFS2_CMDLINE
+#undef CONFIG_CMD_MTDPARTS
#define CONFIG_JFFS2_DEV "nor0"
#endif /* __CONFIG_H */