#undef _CONFIG_UART4 /* internal uart 4 */
#undef CONFIG_SILENT_CONSOLE /* use this to disable output */
+
/*
- * Definition of u-boot build in commands. Check out CONFIG_CMD_DFL if
- * neccessary in include/cmd_confdefs.h file. (Un)comment for getting
- * functionality or size of u-boot code.
+ * BOOTP options
*/
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- & ~CFG_CMD_LOADS \
- & ~CFG_CMD_CONSOLE \
- & ~CFG_CMD_AUTOSCRIPT \
- & ~CFG_CMD_NET \
- & ~CFG_CMD_PING \
- & ~CFG_CMD_DHCP \
- | CFG_CMD_JFFS2 \
- )
-
-#include <cmd_confdefs.h>
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_JFFS2
+
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_CONSOLE
+#undef CONFIG_CMD_AUTOSCRIPT
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_PING
+#undef CONFIG_CMD_DHCP
+
/*
* Boot options. Setting delay to -1 stops autostart count down.
#define CONFIG_INITRD_TAG 1 /* send initrd params */
#undef CONFIG_VFD /* do not send framebuffer setup */
-#define CFG_JFFS_CUSTOM_PART
/*
* Malloc pool need to host env + 128 Kb reserve for other allocations.
*/
#define PRECHARGE_CMD 0x910a8300
#define AUTOREFRESH_CMD 0xa10a8300
-#define CONFIG_INIT_CRITICAL
-
#define BUS32BIT_VERSION
/*
* SDRAM Memory Map
#define MX1FS2_FLASH_INTERLEAVE 2 /* ... made of 2 chips */
#define MX1FS2_FLASH_BANK_SIZE 0x02000000 /* size of one flash bank*/
#define MX1FS2_FLASH_SECT_SIZE 0x00020000 /* size of erase sector */
-#define MX1FS2_JFFS2_PART0_START 0x10200000
-#define MX1FS2_JFFS2_PART0_SIZE 0x00500000
-#define MX1FS2_JFFS2_PART1_START 0x10700000
-#define MX1FS2_JFFS2_PART1_SIZE 0x00900000
#else
#define MX1FS2_FLASH_BUS_WIDTH 2 /* we use 16 bit FLASH memory... */
#define MX1FS2_FLASH_INTERLEAVE 1 /* ... made of 1 chip */
* Right now there is no gain for user, but later on booting kernel might be
* possible. Consider using XIP kernel running from flash to save RAM
* footprint.
- * NOTE: Enable CFG_CMD_JFFS2 for JFFS2 support.
+ * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support.
*/
-#define CFG_JFFS2_FIRST_BANK 0
-#define CFG_JFFS2_FIRST_SECTOR 5
-#define CFG_JFFS2_NUM_BANKS 1
+
+/*
+ * JFFS2 partitions
+ */
+/* No command line, one static partition, whole device */
+/*
+#undef CONFIG_JFFS2_CMDLINE
+#define CONFIG_JFFS2_DEV "nor0"
+#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
+#define CONFIG_JFFS2_PART_OFFSET 0x00050000
+*/
+
+/* mtdparts command line support */
+/* Note: fake mtd_id used, no linux mtd map file */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nor0=mx1fs2-0"
+
+#ifdef BUS32BIT_VERSION
+#define MTDPARTS_DEFAULT "mtdparts=mx1fs2-0:2m@5m(part0),5m@9m(part1)"
+#else
+#define MTDPARTS_DEFAULT "mtdparts=mx1fs2-0:-@320k(jffs2)"
+#endif
/*
* Environment setup. Definitions of monitor location and size with