#undef _CONFIG_UART4 /* internal uart 4 */
#undef CONFIG_SILENT_CONSOLE /* use this to disable output */
-
/*
* BOOTP options
*/
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
-
/*
* Command line configuration.
*/
#define CONFIG_CMD_JFFS2
-#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_CONSOLE
-#undef CONFIG_CMD_AUTOSCRIPT
+#undef CONFIG_CMD_DHCP
+#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_NET
#undef CONFIG_CMD_PING
-#undef CONFIG_CMD_DHCP
-
+#undef CONFIG_CMD_SOURCE
/*
* Boot options. Setting delay to -1 stops autostart count down.
/*
* General options for u-boot. Modify to save memory foot print
*/
-#define CFG_LONGHELP /* undef saves memory */
-#define CFG_PROMPT "mx1fs2> " /* prompt string */
-#define CFG_CBSIZE 256 /* console I/O buffer */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* print buffer size */
-#define CFG_MAXARGS 16 /* max command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* boot args buf size */
-
-#define CFG_MEMTEST_START 0x08100000 /* memtest test area */
-#define CFG_MEMTEST_END 0x08F00000
+#define CONFIG_SYS_LONGHELP /* undef saves memory */
+#define CONFIG_SYS_PROMPT "mx1fs2> " /* prompt string */
+#define CONFIG_SYS_CBSIZE 256 /* console I/O buffer */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* print buffer size */
+#define CONFIG_SYS_MAXARGS 16 /* max command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* boot args buf size */
-#undef CFG_CLKS_IN_HZ /* use HZ for freq. display */
+#define CONFIG_SYS_MEMTEST_START 0x08100000 /* memtest test area */
+#define CONFIG_SYS_MEMTEST_END 0x08F00000
-#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */
-#define CFG_CPUSPEED 0x141 /* core clock - register value */
+#define CONFIG_SYS_HZ 3686400 /* incrementer freq: 3.6864 MHz */
+#define CONFIG_SYS_CPUSPEED 0x141 /* core clock - register value */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#define CONFIG_BAUDRATE 115200
/*
* Definitions related to passing arguments to kernel.
/*
* Malloc pool need to host env + 128 Kb reserve for other allocations.
*/
-#define CFG_MALLOC_LEN (CFG_ENV_SIZE + (128<<10) )
-
-
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128<<10) )
#define CONFIG_STACKSIZE (120<<10) /* stack size */
* Flash Controller settings
*/
-#define CFG_MAX_FLASH_BANKS 1 /* FLASH banks count (not chip count)*/
-#define CFG_MAX_FLASH_SECT 256 /* number of sector in FLASH bank */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* FLASH banks count (not chip count)*/
+#define CONFIG_SYS_MAX_FLASH_SECT 256 /* number of sector in FLASH bank */
#ifdef BUS32BIT_VERSION
#define MX1FS2_FLASH_BUS_WIDTH 4 /* we use 32 bit FLASH memory... */
is not so clear to me. In other words we can provide more informations
to user, but this expects more complex flash handling we do not provide
now.*/
-#undef CFG_FLASH_CFI
+#undef CONFIG_SYS_FLASH_CFI
-#define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* timeout for Erase operation */
-#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* timeout for Write operation */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (2*CONFIG_SYS_HZ) /* timeout for Erase operation */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (2*CONFIG_SYS_HZ) /* timeout for Write operation */
-#define CFG_FLASH_BASE MX1FS2_FLASH_BASE
+#define CONFIG_SYS_FLASH_BASE MX1FS2_FLASH_BASE
/*
* This is setting for JFFS2 support in u-boot.
*/
/* No command line, one static partition, whole device */
/*
-#undef CONFIG_JFFS2_CMDLINE
+#undef CONFIG_CMD_MTDPARTS
#define CONFIG_JFFS2_DEV "nor0"
#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
#define CONFIG_JFFS2_PART_OFFSET 0x00050000
/* mtdparts command line support */
/* Note: fake mtd_id used, no linux mtd map file */
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_FLASH_CFI_MTD
#define MTDIDS_DEFAULT "nor0=mx1fs2-0"
#ifdef BUS32BIT_VERSION
* env. has no sense to us.
*/
-#define CFG_MONITOR_BASE 0x10000000
-#define CFG_MONITOR_LEN 0x20000 /* 128b ( 1 flash sector ) */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR 0x10020000 /* absolute address for now */
-#define CFG_ENV_SIZE 0x20000
+#define CONFIG_SYS_MONITOR_BASE 0x10000000
+#define CONFIG_SYS_MONITOR_LEN 0x20000 /* 128b ( 1 flash sector ) */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR 0x10020000 /* absolute address for now */
+#define CONFIG_ENV_SIZE 0x20000
#define CONFIG_ENV_OVERWRITE 1 /* env is not writable now */
/* Setup CS4 and CS5 */
-#define CFG_GIUS_A_VAL 0x0003fffe
+#define CONFIG_SYS_GIUS_A_VAL 0x0003fffe
/*
* CSxU_VAL:
* | OEA | OEN | WEA | WEN | CSA |EBC| DSZ | 0|SP|0|WP| 0 0|PA|CSEN|
*/
-#define CFG_CS0U_VAL 0x00008C00
-#define CFG_CS0L_VAL 0x22222601
-#define CFG_CS1U_VAL 0x00008C00
-#define CFG_CS1L_VAL 0x22222301
-#define CFG_CS4U_VAL 0x00008C00
-#define CFG_CS4L_VAL 0x22222301
-#define CFG_CS5U_VAL 0x00008C00
-#define CFG_CS5L_VAL 0x22222301
+#define CONFIG_SYS_CS0U_VAL 0x00008C00
+#define CONFIG_SYS_CS0L_VAL 0x22222601
+#define CONFIG_SYS_CS1U_VAL 0x00008C00
+#define CONFIG_SYS_CS1L_VAL 0x22222301
+#define CONFIG_SYS_CS4U_VAL 0x00008C00
+#define CONFIG_SYS_CS4L_VAL 0x22222301
+#define CONFIG_SYS_CS5U_VAL 0x00008C00
+#define CONFIG_SYS_CS5L_VAL 0x22222301
/* f_{dpll}=2*f{ref}*(MFI+MFN/(MFD+1))/(PD+1)
f_ref=16,777MHz
31 |x x x x|x x x x|x x x x|x x x x|x x x x|x x x x|x x x x|x x x x| 0
|XXX|--PD---|-------MFD---------|XXX|--MFI--|-----MFN-----------| */
-#define CFG_MPCTL0_VAL 0x07E723AD
-#define CFG_MPCTL1_VAL 0x00000040
-#define CFG_PCDR_VAL 0x00010005
-#define CFG_GPCR_VAL 0x00000FFB
+#define CONFIG_SYS_MPCTL0_VAL 0x07E723AD
+#define CONFIG_SYS_MPCTL1_VAL 0x00000040
+#define CONFIG_SYS_PCDR_VAL 0x00010005
+#define CONFIG_SYS_GPCR_VAL 0x00000FFB
#define USE_16M_OSZI /* If you have one, you want to use it
The internal 32kHz oszillator jitters */
#ifdef USE_16M_OSZI
-#define CFG_SPCTL0_VAL 0x04001401
-#define CFG_SPCTL1_VAL 0x0C000040
-#define CFG_CSCR_VAL 0x07030003
+#define CONFIG_SYS_SPCTL0_VAL 0x04001401
+#define CONFIG_SYS_SPCTL1_VAL 0x0C000040
+#define CONFIG_SYS_CSCR_VAL 0x07030003
#define CONFIG_SYS_CLK_FREQ 16780000
#define CONFIG_SYSPLL_CLK_FREQ 16000000
#else
-#define CFG_SPCTL0_VAL 0x07E716D1
-#define CFG_CSCR_VAL 0x06000003
+#define CONFIG_SYS_SPCTL0_VAL 0x07E716D1
+#define CONFIG_SYS_CSCR_VAL 0x06000003
#define CONFIG_SYS_CLK_FREQ 16780000
#define CONFIG_SYSPLL_CLK_FREQ 16780000
* one may expect. For instance loadb command do not cares :-)
* So advice is - do not relay on this...
*/
-#define CFG_LOAD_ADDR 0x08400000
+#define CONFIG_SYS_LOAD_ADDR 0x08400000
-#define CFG_FMCR_VAL 0x00000003 /* Reset Default */
+#define CONFIG_SYS_FMCR_VAL 0x00000003 /* Reset Default */
/* Bit[0:3] contain PERCLK1DIV for UART 1
0x000b00b ->b<- -> 192MHz/12=16MHz
0x000b00b ->3<- -> 64MHz/4=16MHz */
#ifdef _CONFIG_UART1
+#define CONFIG_IMX_SERIAL
#define CONFIG_IMX_SERIAL1
#elif defined _CONFIG_UART2
+#define CONFIG_IMX_SERIAL
#define CONFIG_IMX_SERIAL2
#elif defined _CONFIG_UART3 | defined _CONFIG_UART4
-#define CONFIG_IMX_SERIAL_NONE
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_CLK 3686400
-#define CFG_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_CLK 3686400
+#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_CONS_INDEX 1
#ifdef _CONFIG_UART3
-#define CFG_NS16550_COM1 0x15000000
+#define CONFIG_SYS_NS16550_COM1 0x15000000
#elif defined _CONFIG_UART4
-#define CFG_NS16550_COM1 0x16000000
+#define CONFIG_SYS_NS16550_COM1 0x16000000
#endif
#endif
projects / platform / kernel / u-boot.git / blobdiff