*/
/* CPU and board */
-#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
-#define CONFIG_MPC5200 1 /* More exactly a MPC5200 */
+#define CONFIG_MPC5200 1 /* This is a MPC5200 CPU */
#define CONFIG_MOTIONPRO 1 /* ... on Promess Motion-PRO board */
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/*
* Command line configuration.
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_BEDBUG
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO
/*
*/
#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
#define CONFIG_NETCONSOLE 1 /* network console */
-#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
/*
/*
* Autobooting
*/
-#define CONFIG_BOOTDELAY 2 /* autoboot after 2 seconds */
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_STOP_STR "\x1b\x1b"
-#define DEBUG_BOOTKEYS 0
-#undef CONFIG_AUTOBOOT_DELAY_STR
#undef CONFIG_BOOTARGS
-#define CONFIG_AUTOBOOT_PROMPT "Autobooting in %d seconds, " \
- "press \"<Esc><Esc>\" to stop\n", bootdelay
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-
-#define CONFIG_ETHADDR 00:50:C2:40:10:00
-#define CONFIG_OVERWRITE_ETHADDR_ONCE 1
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
/*
* Default environment settings
#define CONFIG_SYS_ATA_DATA_OFFSET 0x0060
#define CONFIG_SYS_ATA_REG_OFFSET CONFIG_SYS_ATA_DATA_OFFSET
#define CONFIG_SYS_ATA_STRIDE 4
-#define CONFIG_DOS_PARTITION
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* select I2C module #2 */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 1 /* 2 bytes per write cycle */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 /* 2ms/cycle + 3ms extra */
-#define CONFIG_SYS_I2C_MULTI_EEPROMS 1 /* 2 EEPROMs (addr:50,52) */
/*
* RTC configuration
/*
* Status LED configuration
*/
-#define CONFIG_STATUS_LED /* Status LED enabled */
-#define CONFIG_BOARD_SPECIFIC_LED
#define ENABLE_GPIO_OUT 0x00000024
#define LED_ON 0x00000010
-#ifndef __ASSEMBLY__
-/*
- * In case of Motion-PRO, a LED is identified by its corresponding
- * GPT Enable and Mode Select Register.
- */
-typedef volatile unsigned long * led_id_t;
-
-extern void __led_init(led_id_t id, int state);
-extern void __led_toggle(led_id_t id);
-extern void __led_set(led_id_t id, int state);
-#endif /* __ASSEMBLY__ */
-
-/*
- * Temperature sensor
- */
-#define CONFIG_DTT_LM75 1
-#define CONFIG_DTT_SENSORS { 0x49 }
-
/*
* Environment settings
*/
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_LOAD_ADDR 0x200000 /* default kernel load addr */
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-
/*
* Various low-level settings
*/
/* Not needed for MPC 5xxx U-Boot, but used by tools/updater */
#define CONFIG_SYS_RESET_ADDRESS 0xfff00100
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#define OF_CPU "PowerPC,5200@0"
#define OF_SOC "soc5200@f0000000"
#define OF_TBCLK (bd->bi_busfreq / 4)