#endif
/* uart */
-# define CONFIG_BAUDRATE 115200
/* The following table includes the supported baudrates */
# define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
# define CONFIG_XILINX_GPIO
# define CONFIG_SYS_GPIO_0_ADDR XILINX_GPIO_BASEADDR
#endif
-#define CONFIG_BOARD_LATE_INIT
/* watchdog */
#if defined(XILINX_WATCHDOG_BASEADDR) && defined(XILINX_WATCHDOG_IRQ)
/* use buffered writes (20x faster) */
# define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
# ifdef RAMENV
-# define CONFIG_ENV_IS_NOWHERE 1
# define CONFIG_ENV_SIZE 0x1000
# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SIZE)
# else /* FLASH && !RAMENV */
-# define CONFIG_ENV_IS_IN_FLASH 1
/* 128K(one sector) for env */
# define CONFIG_ENV_SECT_SIZE 0x20000
# define CONFIG_ENV_ADDR \
#else /* !FLASH */
#ifdef SPIFLASH
-# define CONFIG_SYS_NO_FLASH 1
# define CONFIG_SYS_SPI_BASE XILINX_SPI_FLASH_BASEADDR
# define CONFIG_SPI 1
# define CONFIG_SF_DEFAULT_MODE SPI_MODE_3
# define CONFIG_SF_DEFAULT_CS XILINX_SPI_FLASH_CS
# ifdef RAMENV
-# define CONFIG_ENV_IS_NOWHERE 1
# define CONFIG_ENV_SIZE 0x1000
# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SIZE)
# else /* SPIFLASH && !RAMENV */
-# define CONFIG_ENV_IS_IN_SPI_FLASH 1
# define CONFIG_ENV_SPI_MODE SPI_MODE_3
# define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
# define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
#else /* !SPIFLASH */
/* ENV in RAM */
-# define CONFIG_SYS_NO_FLASH 1
-# define CONFIG_ENV_IS_NOWHERE 1
# define CONFIG_ENV_SIZE 0x1000
# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SIZE)
#endif /* !SPIFLASH */
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MFSL
-
-#if defined(FLASH)
-# define CONFIG_CMD_JFFS2
-# define CONFIG_CMD_UBI
-# undef CONFIG_CMD_UBIFS
-
-# if !defined(RAMENV)
-# define CONFIG_CMD_SAVES
-# endif
-
-#else
-#if defined(SPIFLASH)
-
-# if !defined(RAMENV)
-# define CONFIG_CMD_SAVES
-# endif
-#else
-# undef CONFIG_CMD_JFFS2
-# undef CONFIG_CMD_UBI
-# undef CONFIG_CMD_UBIFS
-#endif
-#endif
-
#if defined(CONFIG_CMD_JFFS2)
# define CONFIG_MTD_PARTITIONS
#endif
-#if defined(CONFIG_CMD_UBIFS)
-# define CONFIG_CMD_UBI
-# define CONFIG_LZO
-#endif
-
#if defined(CONFIG_CMD_UBI)
# define CONFIG_MTD_PARTITIONS
-# define CONFIG_RBTREE
#endif
#if defined(CONFIG_MTD_PARTITIONS)
/* MTD partitions */
-#define CONFIG_CMD_MTDPARTS /* mtdparts command line support */
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
#define CONFIG_FLASH_CFI_MTD
#define MTDIDS_DEFAULT "nor0=flash-0"
/* size of console buffer */
#define CONFIG_SYS_CBSIZE 512
- /* print buffer size */
-#define CONFIG_SYS_PBSIZE \
- (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
/* max number of command args */
#define CONFIG_SYS_MAXARGS 15
#define CONFIG_SYS_LONGHELP
/* default load address */
#define CONFIG_SYS_LOAD_ADDR 0
-#define CONFIG_BOOTARGS "root=romfs"
#define CONFIG_HOSTNAME XILINX_BOARD_NAME
#define CONFIG_BOOTCOMMAND "base 0;tftp 11000000 image.img;bootm"
-#define CONFIG_IPADDR 192.168.0.3
-#define CONFIG_SERVERIP 192.168.0.5
-#define CONFIG_GATEWAYIP 192.168.0.1
/* architecture dependent code */
#define CONFIG_SYS_USR_EXCEP /* user exception */
#define CONFIG_PREBOOT "echo U-BOOT for ${hostname};setenv preboot;echo"
+#ifndef CONFIG_EXTRA_ENV_SETTINGS
#define CONFIG_EXTRA_ENV_SETTINGS "unlock=yes\0" \
"nor0=flash-0\0"\
"mtdparts=mtdparts=flash-0:"\
"setenv stdin nc\0" \
"serial=setenv stdout serial;"\
"setenv stdin serial\0"
+#endif
#define CONFIG_CMDLINE_EDITING
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-
/* Enable flat device tree support */
#define CONFIG_LMB 1
#if defined(CONFIG_XILINX_AXIEMAC)
# define CONFIG_MII 1
-# define CONFIG_PHY_GIGE 1
# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 1
# define CONFIG_PHY_ATHEROS 1
# define CONFIG_PHY_BROADCOM 1
# define CONFIG_PHY_DAVICOM 1
# define CONFIG_PHY_LXT 1
# define CONFIG_PHY_MARVELL 1
-# define CONFIG_PHY_MICREL 1
-# define CONFIG_PHY_MICREL_KSZ9021
# define CONFIG_PHY_NATSEMI 1
# define CONFIG_PHY_REALTEK 1
# define CONFIG_PHY_VITESSE 1
#endif
/* SPL part */
-#define CONFIG_CMD_SPL
#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SPL_BOARD_INIT
-
-#define CONFIG_SPL_LDSCRIPT "arch/microblaze/cpu/u-boot-spl.lds"
-#define CONFIG_SPL_RAM_DEVICE
#ifdef CONFIG_SYS_FLASH_BASE
# define CONFIG_SYS_UBOOT_BASE CONFIG_SYS_FLASH_BASE
#endif
/* for booting directly linux */
-#define CONFIG_SPL_OS_BOOT
-#define CONFIG_SYS_OS_BASE (CONFIG_SYS_FLASH_BASE + \
- 0x60000)
#define CONFIG_SYS_FDT_BASE (CONFIG_SYS_FLASH_BASE + \
0x40000)
#define CONFIG_SYS_FDT_SIZE (16<<10)