* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
*
- * (C) Copyright 2009-2011
+ * (C) Copyright 2009-2015
* Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
* esd electronic system design gmbh <www.esd.eu>
*
* Since the linker has to swallow that define, we must use a pure
* hex number here!
*/
-#define CONFIG_SYS_TEXT_BASE 0x20002000
-
-/*
- * since a number of boards are not being listed in linux
- * arch/arm/tools/mach-types any more, the mach-types have to be
- * defined here
- */
-#define MACH_TYPE_MEESC 2165
-#define MACH_TYPE_ETHERCAN2 2407
+#define CONFIG_SYS_TEXT_BASE 0x21F00000
/* ARM asynchronous clock */
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* 32.768 kHz crystal */
#define CONFIG_SYS_AT91_MAIN_CLOCK 16000000/* 16.0 MHz crystal */
-#define CONFIG_SYS_HZ 1000 /* decrementer freq */
/* Misc CPU related */
#define CONFIG_SKIP_LOWLEVEL_INIT
#define CONFIG_ARCH_CPU_INIT
-#define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f() */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_SERIAL_TAG
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_MISC_INIT_R /* Call misc_init_r */
-#define CONFIG_DISPLAY_BOARDINFO /* call checkboard() */
-#define CONFIG_DISPLAY_CPUINFO /* display cpu info and speed */
#define CONFIG_PREBOOT /* enable preboot variable */
/*
* Hardware drivers
*/
-/* required until arch/arm/include/asm/arch-at91/at91sam9263.h is reworked */
-#define ATMEL_PMC_UHP AT91SAM926x_PMC_UHP
-
/* general purpose I/O */
#define CONFIG_AT91_GPIO
#define CONFIG_ATMEL_USART
#define CONFIG_USART_BASE ATMEL_BASE_DBGU
#define CONFIG_USART_ID ATMEL_ID_SYS
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_BOOTDELAY 3
-#define CONFIG_ZERO_BOOTDELAY_CHECK
/*
* BOOTP options
/*
* Command line configuration.
*/
-#include <config_cmd_default.h>
-#undef CONFIG_CMD_BDI
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_IMLS
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
+
+#ifdef CONFIG_SYS_USE_NANDFLASH
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_USB
+#endif
/* LED */
#define CONFIG_AT91_LED
* SDRAM: 1 bank, min 32, max 128 MB
* Initialized before u-boot gets started.
*/
+#define PHYS_SDRAM ATMEL_BASE_CS1 /* 0x20000000 */
+#define PHYS_SDRAM_SIZE 0x02000000 /* 32 MByte */
+
#define CONFIG_NR_DRAM_BANKS 1
-#define CONFIG_SYS_SDRAM_BASE 0x20000000 /* ATMEL_BASE_CS1 */
-#define CONFIG_SYS_SDRAM_SIZE 0x02000000
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_SDRAM_SIZE PHYS_SDRAM_SIZE
#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE + 0x00100000)
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x01E00000)
#ifdef CONFIG_SYS_USE_DATAFLASH
# define CONFIG_ATMEL_DATAFLASH_SPI
# define CONFIG_HAS_DATAFLASH
-# define CONFIG_SYS_SPI_WRITE_TOUT (5 * CONFIG_SYS_HZ)
# define CONFIG_SYS_MAX_DATAFLASH_BANKS 1
# define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* CS0 */
# define AT91_SPI_CLK 15000000
# define DATAFLASH_TCHS (0x1 << 24)
#endif
-/* NOR flash is not populated, disable it */
-#define CONFIG_SYS_NO_FLASH
-
/* NAND flash */
#ifdef CONFIG_CMD_NAND
# define CONFIG_NAND_ATMEL
# define CONFIG_SYS_MAX_NAND_DEVICE 1
-# define CONFIG_SYS_NAND_BASE 0x40000000 /* ATMEL_BASE_CS3 */
+# define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 /* 0x40000000 */
# define CONFIG_SYS_NAND_DBW_8
# define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
# define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
-# define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIO_PORTD, 15
-# define CONFIG_SYS_NAND_READY_PIN AT91_PIO_PORTA, 22
+# define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PD(15)
+# define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PA(22)
#endif
/* Ethernet */
#define CONFIG_MACB
#define CONFIG_RMII
-#define CONFIG_FIT
#define CONFIG_NET_RETRY_COUNT 20
#undef CONFIG_RESET_PHY_R
-/* USB */
-#define CONFIG_USB_ATMEL
-#define CONFIG_USB_OHCI_NEW
-#define CONFIG_DOS_PARTITION
-#define CONFIG_SYS_USB_OHCI_CPU_INIT
-#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00a00000
-#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9263"
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
-
-/* CAN */
-#define CONFIG_AT91_CAN
-
/* hw-controller addresses */
#define CONFIG_ET1100_BASE 0x70000000
#endif
-#define CONFIG_SYS_PROMPT "=> "
#define CONFIG_SYS_CBSIZE 512
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_LONGHELP
#define CONFIG_CMDLINE_EDITING
+#define CONFIG_AUTO_COMPLETE
/*
* Size of malloc() pool