#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/*
* Serial console configuration
/* USB */
#if 0
#define CONFIG_USB_OHCI
-#define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT
#define CONFIG_USB_STORAGE
-#else
-#define ADD_USB_CMD 0
#endif
+
/*
- * Supported commands
+ * BOOTP options
*/
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_EEPROM | \
- CFG_CMD_FAT | \
- CFG_CMD_EXT2 | \
- CFG_CMD_I2C | \
- CFG_CMD_IDE | \
- CFG_CMD_BSP | \
- CFG_CMD_ELF)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_ELF
+
#if (TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */
-# define CFG_LOWBOOT 1
+# define CFG_LOWBOOT 1
# define CFG_LOWBOOT16 1
#endif
#if (TEXT_BASE == 0xFF800000) /* Boot low with 8 MB Flash */
-# define CFG_LOWBOOT 1
+# define CFG_LOWBOOT 1
# define CFG_LOWBOOT08 1
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
- "flash_vxworks0=run ata_vxworks_args;setenv loadaddr ff000000;bootvx\0" \
- "flash_vxworks1=run ata_vxworks_args;setenv loadaddr ff200000:bootvx\0" \
- "net_vxworks=tftp $(loadaddr) $(image);run vxworks_args;bootvx\0" \
- "vxworks_args=setenv bootargs fec(0,0)$(host):$(image) h=$(serverip) e=$(ipaddr) g=$(gatewayip) u=$(user) $(pass) tn=$(target) s=$(script)\0" \
- "ata_vxworks_args=setenv bootargs /ata0/vxWorks h=$(serverip) e=$(ipaddr) g=$(gatewayip) u=$(user) $(pass) tn=$(target) s=$(script) o=fec0 \0" \
- "loadaddr=01000000\0" \
- "serverip=192.168.2.99\0" \
- "gatewayip=10.0.0.79\0" \
- "user=mu\0" \
- "target=mecp5200.esd\0" \
- "script=mecp5200.bat\0" \
- "image=/tftpboot/vxWorks_mecp5200\0" \
- "ipaddr=10.0.13.196\0" \
- "netmask=255.255.0.0\0" \
+ "flash_vxworks0=run ata_vxworks_args;setenv loadaddr ff000000;bootvx\0" \
+ "flash_vxworks1=run ata_vxworks_args;setenv loadaddr ff200000:bootvx\0" \
+ "net_vxworks=tftp $(loadaddr) $(image);run vxworks_args;bootvx\0" \
+ "vxworks_args=setenv bootargs fec(0,0)$(host):$(image) h=$(serverip) e=$(ipaddr) g=$(gatewayip) u=$(user) $(pass) tn=$(target) s=$(script)\0" \
+ "ata_vxworks_args=setenv bootargs /ata0/vxWorks h=$(serverip) e=$(ipaddr) g=$(gatewayip) u=$(user) $(pass) tn=$(target) s=$(script) o=fec0 \0" \
+ "loadaddr=01000000\0" \
+ "serverip=192.168.2.99\0" \
+ "gatewayip=10.0.0.79\0" \
+ "user=mu\0" \
+ "target=mecp5200.esd\0" \
+ "script=mecp5200.bat\0" \
+ "image=/tftpboot/vxWorks_mecp5200\0" \
+ "ipaddr=10.0.13.196\0" \
+ "netmask=255.255.0.0\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_vxworks0"
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
#endif
/*
* I2C configuration
#define CFG_I2C_EEPROM_ADDR_LEN 2
#define CFG_EEPROM_PAGE_WRITE_BITS 5
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20
-#define CFG_I2C_MULTI_EEPROMS 1
+#define CFG_I2C_MULTI_EEPROMS 1
/*
* Flash configuration
*/
#define CFG_FLASH_BASE 0xFFC00000
-#define CFG_FLASH_SIZE 0x00400000
+#define CFG_FLASH_SIZE 0x00400000
#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x003E0000)
#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */
#define CFG_MAX_FLASH_SECT 512
#define CFG_ENV_SECT_SIZE 0x10000
#define CONFIG_ENV_OVERWRITE 1
#else
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
#define CFG_ENV_OFFSET 0x0000 /* environment starts at the beginning of the EEPROM */
#define CFG_ENV_SIZE 0x0400 /* 8192 bytes may be used for env vars*/
/* total size of a CAT24WC32 is 8192 bytes */
#define CONFIG_ENV_OVERWRITE 1
#endif
-#define CFG_FLASH_CFI_DRIVER 1 /* Flash is CFI conformant */
-#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CFG_FLASH_PROTECTION 1 /* use hardware protection */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Flash is CFI conformant */
+#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CFG_FLASH_PROTECTION 1 /* use hardware protection */
#if 0
#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
#endif
-#define CFG_FLASH_INCREMENT 0x00400000 /* size of flash bank */
+#define CFG_FLASH_INCREMENT 0x00400000 /* size of flash bank */
#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE }
-#define CFG_FLASH_EMPTY_INFO 1 /* show if bank is empty */
+#define CFG_FLASH_EMPTY_INFO 1 /* show if bank is empty */
/*
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CFG_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */
+#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
/*
* Various low-level settings
*/
/* Offset for alternate registers */
#define CFG_ATA_ALT_OFFSET (0x005C)
-/* Interval between registers */
-#define CFG_ATA_STRIDE 4
+/* Interval between registers */
+#define CFG_ATA_STRIDE 4
#endif /* __CONFIG_H */