* (C) Copyright 2003-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
#define CONFIG_MECP5200 1 /* ... on MECP5200 board */
#define CONFIG_MPC5200_DDR 1 /* ... use DDR RAM */
-#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xFFF00000
+#endif
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
#endif
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-#ifdef CONFIG_MPC5200 /* MPC5100 PCI is not supported yet. */
-
#define CONFIG_MII
#if 0 /* test-only !!! */
-#define CONFIG_NET_MULTI 1
#define CONFIG_EEPRO100 1
#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_NS8382X 1
#endif
-#else /* MPC5100 */
-
-#endif
-
/* Partitions */
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#define CONFIG_CMD_ELF
-#if (TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */
+#if (CONFIG_SYS_TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */
# define CONFIG_SYS_LOWBOOT 1
# define CONFIG_SYS_LOWBOOT16 1
#endif
-#if (TEXT_BASE == 0xFF800000) /* Boot low with 8 MB Flash */
+#if (CONFIG_SYS_TEXT_BASE == 0xFF800000) /* Boot low with 8 MB Flash */
# define CONFIG_SYS_LOWBOOT 1
# define CONFIG_SYS_LOWBOOT08 1
#endif
#define CONFIG_BOOTCOMMAND "run flash_vxworks0"
-#if defined(CONFIG_MPC5200)
/*
* IPB Bus clocking configuration.
*/
#undef CONFIG_SYS_IPBSPEED_133 /* define for 133MHz speed */
-#endif
/*
* I2C configuration
*/
/* Use SRAM until RAM will be available */
#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
-#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */
+#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
# define CONFIG_SYS_RAMBOOT 1
#endif
* Ethernet configuration
*/
#define CONFIG_MPC5xxx_FEC 1
+#define CONFIG_MPC5xxx_FEC_MII100
/*
- * Define CONFIG_FEC_10MBIT to force FEC at 10Mb
+ * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
*/
-/* #define CONFIG_FEC_10MBIT 1 */
+/* #define CONFIG_MPC5xxx_FEC_MII10 */
#define CONFIG_PHY_ADDR 0x00
#define CONFIG_UDP_CHECKSUM 1
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-
#define CONFIG_SYS_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */
#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
/*
* Various low-level settings
*/
-#if defined(CONFIG_MPC5200)
#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
#define CONFIG_SYS_HID0_FINAL HID0_ICE
-#else
-#define CONFIG_SYS_HID0_INIT 0
-#define CONFIG_SYS_HID0_FINAL 0
-#endif
#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE