/*
- * (C) Copyright 2006
+ * (C) Copyright 2006-2008
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
#define CONFIG_MISC_INIT_R
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/*
* Serial console configuration
* To select console on the one of 8 external UARTs,
* define CONFIG_QUART_CONSOLE as 1, 2, 3, or 4 for the first Quad UART,
* or as 5, 6, 7, or 8 for the second Quad UART.
+ * COM11, COM12, COM13, COM14 are located on the second Quad UART.
*
* CONFIG_PSC_CONSOLE must be undefined in this case.
*/
-/* #define CONFIG_QUART_CONSOLE 1 */ /* console is on UART1 of QUART1 */
+#if !defined(CONFIG_PRS200)
+/* MCC200 configuration: */
+#ifdef CONFIG_CONSOLE_COM12
+#define CONFIG_QUART_CONSOLE 6 /* console is on UARTF of QUART2 */
+#else
+#define CONFIG_QUART_CONSOLE 8 /* console is on UARTH of QUART2 */
+#endif
+#else
+/* PRS200 configuration: */
+#undef CONFIG_QUART_CONSOLE
+#endif /* CONFIG_PRS200 */
/*
* To select console on PSC1, define CONFIG_PSC_CONSOLE as 1
* and undefine CONFIG_QUART_CONSOLE.
*/
-#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
-#if defined(CONFIG_QUART_CONSOLE) && defined(CONFIG_PSC_CONSOLE)
+#if !defined(CONFIG_PRS200)
+/* MCC200 configuration: */
+#define CONFIG_SERIAL_MULTI 1
+#define CONFIG_PSC_CONSOLE 1 /* PSC1 may be COM */
+#define CONFIG_PSC_CONSOLE2 2 /* PSC2 is PSoC */
+#else
+/* PRS200 configuration: */
+#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
+#endif
+#if defined(CONFIG_QUART_CONSOLE) && defined(CONFIG_PSC_CONSOLE) && \
+ !defined(CONFIG_SERIAL_MULTI)
#error "Select only one console device!"
#endif
#define CONFIG_BAUDRATE 115200
/* USB */
#define CONFIG_USB_OHCI
-#define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT
#define CONFIG_USB_STORAGE
+/* automatic software updates (see board/mcc200/auto_update.c) */
+#define CONFIG_AUTO_UPDATE 1
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
/*
- * Supported commands
+ * Command line configuration.
*/
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- ADD_USB_CMD | \
- CFG_CMD_BEDBUG | \
- CFG_CMD_FAT | \
- CFG_CMD_I2C)
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BEDBUG
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_USB
+
+#undef CONFIG_CMD_NET
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
/*
* Autobooting
*/
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
-#define CONFIG_EXTRA_ENV_SETTINGS \
+#define XMK_STR(x) #x
+#define MK_STR(x) XMK_STR(x)
+
+#ifdef CONFIG_PRS200
+# define CFG__BOARDNAME "prs200"
+# define CFG__LINUX_CONSOLE "ttyS0"
+#else
+# define CFG__BOARDNAME "mcc200"
+# define CFG__LINUX_CONSOLE "ttyEU5"
+#endif
+
+/* Network */
+#define CONFIG_ETHADDR 00:17:17:ff:00:00
+#define CONFIG_IPADDR 10.76.9.29
+#define CONFIG_SERVERIP 10.76.9.1
+
+#include <version.h> /* For U-Boot version */
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "ubootver=" U_BOOT_VERSION "\0" \
"netdev=eth0\0" \
- "hostname=mcc200\0" \
+ "hostname=" CFG__BOARDNAME "\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "ramargs=setenv bootargs root=/dev/mtdblock2 " \
+ "rootfstype=cramfs\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
+ "addcons=setenv bootargs ${bootargs} " \
+ "console=${console},${baudrate} " \
+ "ubootver=${ubootver} board=${board}\0" \
+ "flash_nfs=run nfsargs addip addcons;" \
"bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip;" \
+ "flash_self=run ramargs addip addcons;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
+ "net_nfs=tftp 200000 ${bootfile};" \
+ "run nfsargs addip addcons;bootm\0" \
+ "console=" CFG__LINUX_CONSOLE "\0" \
"rootpath=/opt/eldk/ppc_6xx\0" \
- "bootfile=/tftpboot/mcc200/uImage\0" \
- "baudrate=115200\0" \
- "load=tftp 200000 /tftpboot/mcc200/u-boot.bin\0" \
- "update=protect off FFF00000 +${filesize};" \
- "era FFF00000 +${filesize};" \
- "cp.b 200000 FFF00000 ${filesize}\0" \
- "serverip=192.168.1.1\0" \
- "ipaddr=192.168.133.144\0" \
- "netmask=255.255.0.0\0" \
+ "bootfile=/tftpboot/" CFG__BOARDNAME "/uImage\0" \
+ "load=tftp 200000 /tftpboot/" CFG__BOARDNAME "/u-boot.bin\0" \
+ "text_base=" MK_STR(TEXT_BASE) "\0" \
+ "kernel_addr=0xFC0C0000\0" \
+ "update=protect off ${text_base} +${filesize};" \
+ "era ${text_base} +${filesize};" \
+ "cp.b 200000 ${text_base} ${filesize}\0" \
"unlock=yes\0" \
- "ethaddr=00:02:44:7D:73:3B\0" \
""
+#undef MK_STR
+#undef XMK_STR
#define CONFIG_BOOTCOMMAND "run flash_self"
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CFG_I2C_MODULE 1 /* Select I2C module #1 or #2 */
+#define CFG_I2C_MODULE 2 /* Select I2C module #1 or #2 */
#define CFG_I2C_SPEED 100000 /* 100 kHz */
#define CFG_I2C_SLAVE 0x7F
* TEXT base always at 0xFFF00000
* ENV_ADDR always at 0xFFF40000
* FLASH_BASE at 0xFC000000 for 64 MB (only 32MB are supported, not enough addr lines!!!)
- * 0xFE000000 for 32 MB
- * 0xFF000000 for 16 MB
- * 0xFF800000 for 8 MB
+ * 0xFE000000 for 32 MB
+ * 0xFF000000 for 16 MB
+ * 0xFF800000 for 8 MB
*/
#define CFG_FLASH_BASE 0xfc000000
#define CFG_FLASH_SIZE 0x04000000
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
-#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
-#define CFG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */
+#define CFG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_MONITOR_BASE TEXT_BASE
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
# define CFG_RAMBOOT 1
#endif
/*
* Ethernet configuration
*/
-#define CONFIG_MPC5xxx_FEC 1
+/*#define CONFIG_MPC5xxx_FEC 1*/
/*
* Define CONFIG_FEC_10MBIT to force FEC at 10Mb
*/
#define CONFIG_PHY_ADDR 1
/*
+ * LCD Splash Screen
+ */
+#if !defined(CONFIG_PRS200)
+#define CONFIG_LCD 1
+#define CONFIG_PROGRESSBAR 1
+#endif
+
+#if defined(CONFIG_LCD)
+#define CONFIG_SPLASH_SCREEN 1
+#define CFG_CONSOLE_IS_IN_ENV 1
+#define LCD_BPP LCD_MONOCHROME
+#endif
+
+/*
* GPIO configuration
*/
/* 0x10000004 = 32MB SDRAM */
/* 0x90000004 = 64MB SDRAM */
+#if defined(CONFIG_LCD)
+/* set PSC2 in UART mode */
+#define CFG_GPS_PORT_CONFIG 0x00000044
+#else
#define CFG_GPS_PORT_CONFIG 0x00000004
+#endif
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
+#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
/*
* Various low-level settings
*/
#define CFG_CS1_SIZE 0x00001000
#define CFG_CS1_CFG 0x1d300
+/* Leica - build revision resistors */
+/*
+#define CFG_CS3_START 0x80020000
+#define CFG_CS3_SIZE 0x00000004
+#define CFG_CS3_CFG 0x1d300
+*/
+
/*
* Select one of quarts as a default
* console. If undefined - PSC console
* One of four SC16C554 UARTs is selected with
* A3-A4 (DA5-DA6) lines.
*/
-#if (CONFIG_QUART_CONSOLE > 0) && (CONFIG_QUART_CONSOLE < 5)
+#if (CONFIG_QUART_CONSOLE > 0) && (CONFIG_QUART_CONSOLE < 5) && !defined(CONFIG_PRS200)
#define CFG_NS16550_COM1 (CFG_CS2_START | (CONFIG_QUART_CONSOLE - 1)<<5)
#elif (CONFIG_QUART_CONSOLE > 4) && (CONFIG_QUART_CONSOLE < 9)
#define CFG_NS16550_COM1 (CFG_CS1_START | (CONFIG_QUART_CONSOLE - 5)<<5)
#define CONFIG_USB_CLOCK 0x0001BBBB
#define CONFIG_USB_CONFIG 0x00005000
+#define CONFIG_AUTOBOOT_KEYED /* use key strings to stop autoboot */
+#define CONFIG_AUTOBOOT_STOP_STR "432"
+#define CONFIG_SILENT_CONSOLE 1
+
#endif /* __CONFIG_H */